仿形軸 的英文怎麼說

中文拼音 [fǎngxíngzhóu]
仿形軸 英文
profiled shaft
  • 軸 : 軸Ⅰ名詞1. （圓柱形的零件） axle; shaft 2. （對稱部分的直線） axis 3. （圓柱形的纏繞器物） roller; spool Ⅱ量詞（用於纏在軸上的線以及裝裱帶軸子的字畫）
  1. Based on the " fangsheng - i " robot fish of harbin engineering university auv lab, at first the analysis of the relations of pectoral fin ' s attack angle and lift in vertical plane is done in this paper, using the robot fish ' s hydrodynamic results by the panel method ' s, then setting up the motion model in vertical plane is done. finally animation the robot fish ' s motion in horizontal plane is finished

    論文以哈爾濱工程大學軍用智能水下機器人國防重點實驗室的「仿生? 」號仿魚機器人為對象，利用面元法計算的仿魚機器人水動力結果，並分析了垂直面內胸鰭的攻角與升力的關系，建立了垂直面內的模型，根據軸變形模擬了仿魚機器人水平面內的直航和偏航。
  2. Abstract : guiding accuracy of casting mould depends on structure and oscillation parameters, such as elastic deformation of guiding leaf - springs, play of bearings between linkages, stroke and frequency of mould oscillation, etc. in this paper, these factors are studied by means of kinetic and dynamic analysis of oscillating mechanism

    文摘:通過對連鑄機結晶器振動機構的運動學和動力學分析，研究了導向板彈簧的彈性變形、連桿軸承間隙等結構參數及振幅、振動頻率等運動參數對結晶器仿弧誤差的影響。
  3. A rotary cell culture system was designed, which was composed of micromotor, rotate part, gear part and et al. in this system, tubular scaffold can rotate slowly around own major axis. by means of this, three - dimension tissues or organs can be cultured in vitro

    我們還特別設計了旋轉培養裝置，通過微型馬達驅動，減速裝置作用使旋轉部分繞自身中心水平軸做緩慢轉動，從而使置於旋轉部件上的管形支架繞其正中長軸作緩慢旋轉，其原理與美國genzrpe公司的rccs （ rotarycellculturesystemrccs ）系統相仿。
  4. In this thesis, six topological characteristics and geometry characteristics are proposed that are invariant under affine transformations and axonometric projection. the definition of homograph is given based on these characteristics, and then the recognizing method of the homograph is proposed according to the definition of homograph at the same time

    其次，根據仿射不變性提出了6個用來描述多邊形形狀的拓撲特徵和幾何特徵，這些特徵在軸測投影下是不變的，以這些特徵為約束條件給出了在軸測投影下類似形的定義。
  5. The meassure to reduce the static error when manufacturing axial parts on a hydralic profiling tool slide is deduced in theory with positive feedback adjusting method

    本文應用順饋校正的方法，從理論上導出了在車床上用液壓仿形刀架加工軸類零件減小穩態誤差的措施。
  6. Abstract : the meassure to reduce the static error when manufacturing axial parts on a hydralic profiling tool slide is deduced in theory with positive feedback adjusting method

    文摘:本文應用順饋校正的方法，從理論上導出了在車床上用液壓仿形刀架加工軸類零件減小穩態誤差的措施。
  7. Camsahft coping lathe

    凸輪軸仿形車床
分享友人
分享到 Line

分享到臉書