位置線指示器 的英文怎麼說

中文拼音 [wèizhìxiànzhǐshìqì]
位置線指示器 英文
line-of-position indicator
  • 位 : Ⅰ名詞1 （所在或所佔的地方） place; location 2 （職位; 地位） position; post; status 3 （特指皇帝...
  • 置 : 動詞1. （擱; 放） place; put; lay 2. （設立; 布置） set up; establish; arrange; fix up 3. （購置） buy; purchase
  • 線 : 名詞1 （用絲、棉、金屬等製成的細長的東西） thread; string; wire 2 [數學] （一個點任意移動所構成的...
  • 指 : 指構詞成分。
  • 示 : Ⅰ動詞（擺出或指出使人知道; 表明） show; indicate; signify; instruct; notify Ⅱ名詞1 [書面語] （給...
  • 器 : 名詞1. （器具） implement; utensil; ware 2. （器官） organ 3. （度量; 才能） capacity; talent 4. （姓氏） a surname
  • 指示 : 1 （指給人看） indicate; point out2 （指示下級） instruct 3 （指示的話或文字） directive; instruc...
  1. On the basis of familiar with can bus and gsm communication, considering hev ( hybrid electric vehicle ) battery administrative system ' s demand for the host pc monitoring system, i have designed can - rs232 converter gateway to realize transmission the real - time data from can node to rs232 serial port, which is carried out by the project of at89c52 mcu + sja1000 can controller + 82c250 can controller interface. host monitoring software has accomplished real - time datas display, storage, historical datas graph analysis and storage fashion change from access to excel, at the same time, realized important datas transmission remotely with tc35 short message module. system software programs in assembly and vb

    Can - rs232轉換網關採用at89c52微處理器+ sja1000can控制器+ pca82c250can控制器介面實現對can總線節點通訊的監聽，並將其轉換成rs232串口電平發送到pc機串口，同時用siemens公司的tc35模塊和at指令實現現場採集系統重要數據和錯誤信息的短消息通訊。在上位pc機監控系統中，主要完成的是對串口設置的選擇控制、現場採集數據的實時刷新顯示、歷史數據的圖表分析及數據的access數據庫存儲和excel電子表格的轉換。系統軟體採用匯編語言和vb實現。
  2. When it arrives at the predetermined destination, the robot controls multi - putting - ball mechanisms and puts the game - ball into the drum simultaneously. on the other side, on the basis of the theory and experiment, we subjoin a line - tracking device in the robot system, ensuring the correct moving of the robot along the white index line on the venue, in order to increase the accuracy of orientation. during the automatic moving, the robot measures the position on the venue by itself, moreover, judging its direction and automatic cut - away with the single - chip microcomputer. this system has been finished the experiment, and find credibility, be in point

    同時，為了保證機器人正確地沿著比賽場地上的指示線行走，提高機器人定位的準確性，還從理論和實驗的角度，在機器人上增加了一套尋線系統，以便機器人在其自動行走的過程中，隨時檢測自身的位置狀態，判斷偏離方向，進行自動的糾正。這一套尋線系統已完成了實驗，且比較可靠、適用。
  3. Preliminary results indicate that the standard and low electromagnetic interaction packages in geant4 give almost identical simulation on emc, the detector performance, such as energy / position resolution, satisfies requirements of physics design. different behaviors of hadrons and electrons in emc will be helpful for particle discrimination, such as e / discrimination. the complete and perfect offline simulation software will play an important role in physics study at bes

    初步結果顯示:標準和低能兩種電磁相互作用模擬軟體包在bes能區給出了相同的模擬結果;探測器的運行指標，如能量解析度和位置解析度，滿足物理設計指標;強子和電子在emc中的不同行為將會給進一步的粒子鑒別（如e /鑒別）提供幫助;完整而完善的離線模擬軟體將在今後bes上的物理研究發揮重要作用。
  4. Ate plays a more and more important role in the test and repair of aircraft avionics, and can considerably improve servicing quality and efficiency. our task is to develop a new type of ate used to test six kinds of aircraft avionics instruments located in the cockpit. it should be able to fulfill the test of all functions and performances of each instruments according to it ’ s component maintenance manual

    本文研究一種新的航空儀表自動測試設備，能對六種分佈於駕艙內的指示型航空電子儀表?空速馬赫數指示器、電動氣壓高度表、無線電距離磁指示器、地平儀、姿態指示儀、水平位置指示儀進行檢測，完成維修手冊所規定的全部功能、性能方面的綜合測試。
  5. Note : the valve is shipped in the closed position. the indicator on the plastic sleeve is aligned with the vertical scribed line on the stem

    注意：閥門裝運時是處于關閉位置。塑料套筒上的指示器與閥桿上的垂直刻線對齊。
  6. The measurement system can automatically control the movement of servo motor and communicate with vna through gpib bus to setup the measurement variable automatically, measure the phase of s parameter. it also can progress the measurement data on the background, display the results by graph data, store them in the data files

    系統自動控制伺服電機的運行，對測試探頭完成指定的移動定位;通過gpib總線與矢量網路分析儀器通信，自動完成相關測量參數的設置以及s參數的相位測量;對測得的數據進行后臺處理，將結果以圖形、數據文件的方式顯示、保存。
  7. Air - position indicator

    空中線位置指示器
分享友人
分享到 Line

分享到臉書