內軸承泵 的英文怎麼說
中文拼音 [nèizhóuchéngbèng]
內軸承泵
英文
pumwith internal bearing（s）- 內 : 名詞1. （內部; 里頭; 里邊） inner; inside; within 2. （妻子或妻子的親屬） one's wife or her relatives 3. （姓氏） a surname
- 軸 : 軸Ⅰ名詞1. （圓柱形的零件） axle; shaft 2. （對稱部分的直線） axis 3. （圓柱形的纏繞器物） roller; spool Ⅱ量詞（用於纏在軸上的線以及裝裱帶軸子的字畫）
- 承 : Ⅰ動詞1 （托著; 接著） bear; hold; carry 2 （承擔） undertake; contract （to do a job） 3 （客套話...
- 泵 : 名詞（吸入和排出流體的機械） pump
- 軸承 : [機械工程] bearing; axle bearing; bearing of shafts; gudgeon block; mechanical bearing; pillow; s...
-
For the 30. 2mm shaft, there are still larger over measure to load. the strength is increased by optimization. for ? 17. 4mm shaft, the strength is increased by enlarge the inner dimension of the spline ; for 30. 2mm shaft, the strength is increased by adjust the structure at the boundary between the key groove and the ring groove, the highest stress of the shaft is at bottom and terminal of the spline after optimization
其中對17 . 4mm泵軸的優化，通過增大花鍵內徑，提高了花鍵齒底的強度，降低了應力集中點附近的應力；對30 . 2mm電機軸的優化，通過在軸承鍵的環槽端增加倒角，有效降低了該位置的應力集中，使軸的最大應力點從軸承鍵與環槽的交界處轉變到花鍵根部與收尾的交界處，提高了電機軸整體結構強度的合理性。To ensure the charging pump working reliably, the following measures should be adopted : ( 1 ) adopting modified circular casing to reduce the radial force of the impeller and decrease the seal clearance ; ( 2 ) using radical ribs on impeller and helical sealing on shaft to realize minor pressure differential ; ( 3 ) using back pressure stuffing box to ensure sealing under small packing force ; ( 4 ) adopting self - lubricant flexible graphite stuffing for absorption of solids entering in the graphite in case of leaking
為確保灌注泵可靠工作，提出改進措施： （ 1 ）採用改型環形泵體降低葉輪的徑向力，減小軸封間隙，抑制泄漏； （ 2 ）採用背葉片降低葉片根部壓頭，獲得微壓，使軸封兩端承受較小壓差； （ 3 ）採用螺旋密封降低軸封兩端壓差，在保持微壓的同時避免出現負壓，密封效果更好； （ 4 ）採用反壓式填料密封結構，在很小的壓緊力下，即可保證密封； （ 5 ）採用具有潤滑功效的柔性石墨填料，即使發生軸封泄漏，進入石墨內部的固相顆粒也將隨著石墨的消耗而被鉆井液吸收。3. sliding bearing and isolation cover are the key parts which influence magnetic force pumps " safely running, pump ' s interior pressure and cooling holes are induced through analyzing outer and inside alnicos, sliding bearings " cooling flux
滑動軸承和隔離套是影響磁力泵可靠性的關鍵部件，通過分析冷卻內外磁鋼和滑動軸承的冷卻流量，反推計算出泵內壓力場，給出冷卻孔設計的方法。
分享友人