刀形開關 的英文怎麼說
中文拼音 [dāoxíngkāiguān]
刀形開關
英文
contact breaker-
Attachment plug blades for use in cord sets and power - supply cords
塞繩裝置和電源線用連接插頭刀形開關The exploitation and study of this system have got great success, compared with the ones of the same type, this system is more open and more easily used to merge with cad and cam, it runs stably, is convenient to be maintained and the interface is friendly and intuitional. its usage can be grasped quickly. according to the input information, it can automatically display different properties of nc codes in different colors, and zoom in or zoom out the figure of tool nose paths dynamically
本系統的開發研究已取得實質性成果，與國內同類的數控系統相比，具有真正的開放性，易於實現與cad cam軟體集成，運行穩定，維護方便，界面友好直觀，易學易用，能根據輸入自動顯示不同顏色以區廣西大學頎士學趕文募于； m咖ss平臺肘開俠尤三劫肛前喊在系統開發研窮分代碼的屬性，能動態縮放顯示刀具軌跡圖形，此外，它有較好的多任務性和獨立性，能在加工時執行其它windows應用程序而不影響加工，控制器甚至能在pc端操作系統關閉時繼續完成加工，可用軟體控制面板或硬體操作面板兩種方式操縱機床。Based on years of research and experience, we have extracted the best to organize a set of novel approach. this refined approach can be adopted according to various regions of deformation and various severities. this novel rectification, without operation, takes only 30 minutes ( for one joint ) and the deformed region can be straightened immediately
? ?因此本院經以多年來的鉆研及臨床經驗，去蕪存菁，研究組合一套突破傳統的技術，采精捷新法，可依患者不同畸型腳部位，按其輕重程度予以採用，這種新醫術矯正，膝部免開刀， （一個關節）約30分鐘矯正，腿部變形部位立即挺直。For cutting the composite lock gear with unequal tooth thickness, a study is made on the design method of gear sharper cutter with nonstandard parameter involute tooth profile and noninvolute tooth profile. the cutter tooth arrangement, the choice of teeth number of the cutter and the basic method of cutter design are discussed ; and a new method of choosing deflection factor by using limited area is presented. and the curve of relationship between rear angle on tooth crest and helical angle on tooth side of the cutter is given so as to give a basis for the gear sharper cutter to choose its parameters. to design nonstandard gear sharper cutter by adopting the method mentioned above will simplify the calculation and will increase the efficiency of design
研究加工不等齒厚的非標準參數漸開線齒形，與非漸開線齒形復合的鎖閉齒輪插齒刀刀齒的排列、刀具齒數的選擇以及刀具設計的基本方法，介紹用限制區域選擇插齒刀變位系數的新方法，並給出刀具齒頂后角與側螺旋角的關系曲線，為插齒刀參數的選擇提供依據.結果表明，採用上述方法設計非標準復合齒輪插齒刀，可簡化計算和提高設計效率This kind of switch use the unilateral fin - line as the basic transmission line, the beam lead pin diode of alpha co. ltd is the control element, there is two diodes in each channel and they are welded in circuit in parallel connection
本課題主要研究的是毫米波鰭線pin管單刀雙擲開關。該開關採用單側鰭線作為基本傳輸線，控制器件選用alpha公司的梁式引線pin二極體，每路使用兩只，採用並聯形式焊接在電路中。The difficulty in design microstrip pin sp3t switch is the via hole for grounding. we use both the radial parts and the via hole to get a good result. the fin - line pin switch is fully simulated using full - wave analysis, the parasitic parameter and the circuit assemble need to be considered
微帶結構上過孔微波接地效果的不理想，是微帶單刀三擲開關的難點，本文採用了扇形的微波接地和過孔直流接地結合起來，較好的解決了這一問題。分享友人