劑量反應曲線 的英文怎麼說
中文拼音 [jìliángfǎnyīngqūxiàn]
劑量反應曲線
英文
dose response curve- 劑 : Ⅰ名詞1 （藥劑; 制劑） a pharmaceutical or other chemical preparation 2 （某些有化學作用的物品） a...
- 量 : 量動1. （度量） measure 2. （估量） estimate; size up
- 反 : Ⅰ名詞1 （方向相背） reverse side 2 （造反） rebellion 3 （指反革命、反動派） counterrevolutionari...
- 應 : 應動詞1 （回答） answer; respond to; echo 2 （滿足要求） comply with; grant 3 （順應; 適應） suit...
- 曲 : 曲名詞1 （一種韻文形式） qu a type of verse for singing which emerged in the southern song and ji...
- 線 : 名詞1 （用絲、棉、金屬等製成的細長的東西） thread; string; wire 2 [數學] （一個點任意移動所構成的...
- 劑量 : [物理學] [醫學] dosage; dose; dosis劑量槽 dosage bunker; 劑量測定（法） dosimetry; health work; ...
- 曲線 : [數學] curve; bight; bought; profile; net曲線板 french curve; irregular curve; curve board; splin...
-
The results indicated that the dimension, shape and purity of base material could meet the functional demand of solid lubricant ; the thermal decomposition temperature of ptfe resin exceeds 400 c, but organic and inorganic packing filler added in ptfe made the water absorption rate of composite material increased, melting temperature and decomposition temperature decreased, in the meanwhile oxidative decomposition reaction was accompanied ; polar groups such as c = o, c - o - c and so on in the carbon fiber surface is advantageous to increase compatibility with other components and interlayer shearing strength ; uniform design experimental method could help to find the relationship between formula and frictional property by relatively small tests. the developing trend of each formula ' s friction coefficient could be showed by fitting curve ; the friction coefficient with no copper powder or graphite in formula was relatively big. this fact showed that copper powder and graphite should be used cooperatively ; it was found that when the ratio of copper powder to graphite by weight is 15 : 60, 30 : 30 - 40 and 60 : 15 - 30 respectively, the friction coefficient was relatively small. the degree of crystallinity of pure ptfe reached maximum by air cooling and the abrasion loss also reached maximum among three ones ; at the same time, the abrasion loss of solid lubricant sample was also the biggest among three ones ; when solid lubricant matched with 45 # steel axle or gcrl5 steel axle, lubricant transfer film could be formed on metal surface, thus direct contact between the surface of metal friction pair rings was reduced. their working life was elongated extremely ; there was mainly much graphite, a little ptff, moo3, feso4, cus and so on in lubricant transfer film
試驗結果表明：所選原料的尺寸、形狀及純度可滿足固體潤滑劑的性能要求；聚四氟乙烯樹脂熱分解溫度超過400 ，但在ptfe中加入無機填料會使復合材料吸水率提高，熔融溫度及分解溫度降低，且伴有氧化分解反應；碳纖維表面含有c = o及c - o - c等極性基團，有利於提高其與其它組分的相容性，提高層間剪切強度；均勻設計試驗方法能夠用較少的試驗次數找出配方與摩擦性能間的關系，擬合曲線基本能表示各配方的摩擦系數發展趨勢；配方中不加銅粉或不加石墨，其摩擦系數均較高，說明銅粉和石墨應該配合使用；當銅粉15份、石墨60份時，銅粉30份、石墨30 - 40份時，銅粉60 、石墨15 - 30份時，摩擦系數均具有較低值；純聚四氟乙烯樹脂在空氣冷卻時結晶度最大，磨損量也是三者中最大的；同時，固體潤滑劑試樣在空氣冷卻時的磨損量也是三者中最大的：不論是固體潤滑劑與45 #鋼軸配副或是固體潤滑劑鑲嵌入銅套后與gcr15鋼軸配副，在金屬表面均可形成潤滑轉移膜，從而減少金屬摩擦副表面間的直接接觸，大大延長其使用壽命;轉移膜中主要含有較多的石墨、少量聚四氟乙烯、 moo 。The ignition process of emulsified fuel ' s catalytic reforming reaction in constant volume chamber was studied and the ignition curves of diesel oil, emulsified fuel ( containing 20wt % water ) with or without catalyst were compared
摘要為研究乳化油的點火延遲，從實驗和計算兩方面研究了催化重整反應對乳化油著火過程的影響，對比了柴油和摻水量為20 % （質量比）乳化油在有、無催化劑條件下的溫升曲線。The output signal of pda is affected by the suspended particle concentration, particle size, and the type and dosage of coagulant as well. by analysing the fi curve, it is found that the characteristic parameters of fi curve closely relate to aggregates size and turbidity removal the aggregates size and turbidity removal achieve the maximum when the amplitude of fluctuation is the maximum. the mean diameter and fractal dimension increase with agitation time, and finally reach a steady - state
通過對混凝過程的在線監測和對pda輸出信號fi曲線的數學解析表明： fi曲線綜合反映了懸濁液中膠體顆粒濃度和顆粒粒徑，混凝劑種類和投量很大程度上影響了fi曲線形狀， fi曲線的特徵值與絮凝體平均粒徑和濁度去除率之間具有良好的相關關系，在振幅最大處，濁度去除率達到最高，絮體平均粒徑最大，該條件下對應的投藥量為最佳投藥量。Dose response curve
劑量反應曲線分享友人