匯編器電路 的英文怎麼說

中文拼音 [huìbiānqìdiànlù]
匯編器電路 英文
combiner circuit
  • 匯 : Ⅰ動詞1 （匯合） converge 2 （聚集; 聚合） gather together 3 （通過郵電局、 銀行把款項劃撥到別處）...
  • 編 : Ⅰ動詞1 （編織） weave; plait; braid 2 （組織; 排列） make a list; arrange in a list; organize; gr...
  • 器 : 名詞1. （器具） implement; utensil; ware 2. （器官） organ 3. （度量; 才能） capacity; talent 4. （姓氏） a surname
  • 電 : Ⅰ名詞1 （有電荷存在和電荷變化的現象） electricity 2 （電報） telegram; cable Ⅱ動詞1 （觸電） give...
  • 路 : 1 （道路） road; way; path 2 （路程） journey; distance 3 （途徑; 門路） way; means 4 （條理） se...
  • 匯編 : 1 （把文章、文件編在一起） collect and edit; compile; assemble 2 （編在一起的文章、文件等） assem...
  • 電路 : [訊] circuit （ckt）; electric circuit; electrocircuit電路板 circuit board; 電路保持 guard of a c...
  1. Part two : design the schematic of the intelligent communication card ; to apply protel99 software to design sch and pcb charts, then send them to the factory ; to debug on the hardware and test on can bus chip ; to program assemble language control and can bus communication software of the intelligent communication card and debug on the super ice16 simulator ; to utilize the super ice 16 simulator to debug the control programs of the communication card online ; link to control card and debug the can bus communication program online ; to debug the system on eprom

    第二部分：設計can總線智能通信卡的硬體電路，應用protel99設計軟體繪制原理圖及印刷電路板圖，並送廠製作板卡電路板:智能通信卡硬體製作和can總線晶元調試;編寫通信卡控制及can總線通信匯編語言程序並編譯;在superice16模擬器上在線模擬調試控製程序;連接系統控制卡，模擬調試can總線通信程序;程序燒入eprom晶元，進行系統eprom模擬調試;介面系統驅動程序及測試軟體調試。
  2. The program is written by assemble language to control the movement of the vacuum circuit breaker with pma. the program also can monitor the environmental temperature, control voltage, closing displacement, zero point of contactor voltage

    用匯編語言編製程序對配永磁機構的真空斷路器的分、合閘進行控制，同時對其運行的環境溫度、控制電壓、合閘位移和觸頭間隙電壓過零點等狀態進行實時監測。
  3. In this course, we study low - power computer design techniques involving mos circuits, logics, computer organization, function units, pipeline, bus protocols, memory subsystems, compiler, os, and virtual machines

    本課程中，我們將研讀計算機低功耗設計技術，內容涵蓋mos電路，邏輯，計算機組織，功能單元，管線處理，匯流排規約，記憶體子系統，編譯器，作業系統，及虛擬機等的相關設計。
  4. The main two process of the development on system is as follows : part one : using prote199 software to design the sch chart of the analog signal input card and complete pcb charts, then have them made in factory ; to debug on the hardware ; to program assemble language control software of the analog signal input card and debug on the super ice 16 simulator ; to utilize the super ice 16 simulator to link card to debug the control programs online ; to embed the control program debugged successfully into eprom and debug the system on eprom

    系統研製開發過程主要分兩大部分：第一部分：應用protel99設計軟體設計模擬量輸入卡的硬體原理，規劃設計印刷電路板圖並送廠製作板卡電路板；模擬量輸入卡硬體製作和調試；編寫模擬量輸入卡匯編語言控製程序，在superice16模擬器上編譯調試；編譯后的控製程序在superice16模擬器上以在線方式模擬調試；模擬調試成功的控製程序燒入eprom晶元，進行系統eprom模擬調試。
  5. Combined with the researching and developing process of " the cbm system in fujian province ", the feasible scheme of the inter - faculty courses synthetic analysis ( namely intelligent management system of electric power equipment ' s condition ) are proposed to work out the module of intellectual ized diagnose and synthetic analysis to electric power equipment, which use the modern theory such as rough set theory, artificial neural net and genetic algorithm etc. emphasizing on the inter - faculty courses analysis, we analyzed the effect of this scheme based on " the instance collection of the limitation, and fault of main transformer in the fujian power system during recent years ", and then got a satisfying result. as the core of the cbm center of electric power equipment, the intelligent management system is the necessary measure to the cbm of equipment power system

    本文介紹了狀態檢修的國內外發展趨勢和現狀，結合「福建省電力設備狀態檢修系統」項目研發過程，利用粗糙集理論、人工神經網路和遺傳演算法等現代理論，提出了跨專業綜合分析（即「電力設備狀態智能管理系統」 ）可行方案，編制電力設備智能綜合診斷分析模塊，並以「福建省電網近年來主變壓器缺陷或故障情況匯總表」為例，以跨專業分析為側重點，對本方案的效果進行計算和分析，結果令人滿意， 「電力設備狀態智能管理系統」作為「福建省電力設備狀態檢修中心」的核心，是電力設備狀態診斷不可缺少的手段。
分享友人
分享到 Line

分享到臉書