噴嘴內徑 的英文怎麼說

中文拼音 [pēnzuǐnèijìng]
噴嘴內徑 英文
nozzle bore
  • 噴 : 噴動詞1. （液體等受壓力而射出） spurt; spout; gush; jet 2. （噴灑） spray; sprinkle
  • 嘴 : 名詞1. （口的通稱） mouth 2. （形狀或作用像嘴的東西） anything shaped or functioning like a mouth 3. （指說話） talk; speak
  • 內 : 名詞1. （內部; 里頭; 里邊） inner; inside; within 2. （妻子或妻子的親屬） one's wife or her relatives 3. （姓氏） a surname
  • 徑 : Ⅰ名詞1 （狹窄的道路; 小路） footpath; path; track 2 （達到目的的方法） way; means 3 （直徑的簡稱...
  1. Strong and high effective mixing of swzzero gravity particle mixer can meet your demand. two mixing axles make a equal speed and reverse rotation in horizontal tube. oars on mixing axle make the materials do radial motion, circular motion and axial motion. in a short time, the particle can be stirred homoginously. nozzel on cover of tube can be used when the solid is mixed with liquid

    無重力粒子混合機（以下簡稱無重力）以強烈、高效混合而來滿足用戶需求，臥式筒體內兩根攪拌軸等速反向旋轉，攪拌軸等速反旋轉，攪攔軸上特殊布置的漿葉確保物料徑向、環向、軸向三向運動，形成復合循環，在極短的時間內達到均勻混合，筒蓋上布置霧化噴嘴供你固液混合時使用。
  2. According to the experimental data of droplet size 、 particle spectrum range 、 droplet cone shape 、 flow rate 、 cover area and cover area rate which obtained through changing the pressure of power sprayer and the nozzle diameter in greenhouse ， this paper made comparative analysis on atomizing performance in same pressure and different nozzle type between same nozzle type and different pressure. the conclusion is that : the ejection rate and the droplet cone shape change with the variation of pressure and nozzle diameter ， average particle diameter decreases obviously and particle quantity increases obviously with the increase of pressure and decrease of nozzle diameter. these results will lay experimental foundation for precise spraying 、 low pollution and highly effective operation

    本文根據溫室內動力噴霧機壓力與噴嘴孔徑的變化影響霧滴大小、粒譜范圍、霧錐形狀、流量、覆蓋面積及覆蓋面積率的試驗數據，對相同壓力下不同噴嘴型號和相同噴嘴型號時壓力不同時的微粒化性能進行對比分析和研究，得到如下結論噴出量與霧錐形狀隨著壓力和噴嘴孔徑大小變化而變化；平均粒徑隨著壓力的增加和噴嘴孔徑的減小而明顯減小；粒數隨著壓力的增加和噴嘴孔徑的減小而明顯增多，為精噴量、低污染、高防效的防除作業奠定了實驗基礎。
  3. Analyzing the finished sprinkler products in our country and overseas, testing all sorts of sprinkler parameters ( elevation of sprinkler, diameter of the nozzle, working pressure, the range of water, uniformity of spray irrigation, intensity of spray irriga tion, the degree of atomization ) so as to compare with the new style sprinkler install with pressure adjuster

    對國內和國外的一些中壓噴頭成品進行分析、研究、測試取得實際的各項參數（噴射仰角、噴嘴直徑，工作壓力、射程、噴灌均勻度、噴灌強度、霧化程度）以便和安裝「壓力調節器」后的噴頭進行比較2
  4. ( 4 ) the droplets diameter of the combined spin - flow pressure spray drying are between 30um and 150um and the ranges of the droplets are narrow. the average diameter of the droplets is between 50 um and 100 um and the spraying angle can be adjusted from 30 to 180

    （ 4 ）採用旋流式組合壓力噴嘴霧化后的液滴直徑大都分佈在30 150um之間，霧滴分佈范圍較窄，其霧化的平均液滴直徑在50 100um左右，壓力噴嘴的霧化角度可在150 180范圍內。
  5. According to the rheological properties of melted abs filament during extrusion from fdm ' s nozzle, on the basis of research on extruded filament section shape, the compensation model of ideal contour line is established, and a new technique for compensating inner or outer contour line of workpiece is put forward, which should depend on the real width of extruded filament ( instead of nozzle radius ) and the real dimensional shrinkage of workpiece

    根據abs絲從噴頭擠出過程中的流變性能，在研究fdm工藝噴頭擠出絲截面形狀的基礎上，建立了理想輪廓線的補償模型，並提出了根據擠出絲實際寬度（而非噴嘴孔直徑）和零件尺寸實際收縮量補償零件內、外輪廓的新方法，驗證試驗結果表明該補償模型和補償方法正確可行。
分享友人
分享到 Line

分享到臉書