噴嘴分離 的英文怎麼說

中文拼音 [pēnzuǐfēnlí]
噴嘴分離 英文
jet separation
  • 噴 : 噴動詞1. （液體等受壓力而射出） spurt; spout; gush; jet 2. （噴灑） spray; sprinkle
  • 嘴 : 名詞1. （口的通稱） mouth 2. （形狀或作用像嘴的東西） anything shaped or functioning like a mouth 3. （指說話） talk; speak
  • 分 : 分Ⅰ名詞1. （成分） component 2. （職責和權利的限度） what is within one's duty or rights Ⅱ同 「份」Ⅲ動詞[書面語] （料想） judge
  • 離 : Ⅰ動詞1 （離開） leave; part from; be away from; separate 2 （背離） go against 3 （缺少） dispens...
  1. As to the work about theory analysis, at first, the paper describes the atomizing and humidifying process of the centrifugal nozzle with firing pin type, high pressure and little aperture and liquid physical properties. later, combining with the structure characters of this kind of nozzle, the paper studies on the theory of the atomizing and humidifying process by three phases, which is water film forming phase, water film falling into pieces phase, and heat and mass transfer between water and air phase in turn

    理論工作方面，首先描述了撞針型高壓小孔徑離心式噴嘴的霧化加濕過程和液體的物理性質，然後結合撞針型高壓小孔徑離心式噴嘴的結構特點，將其霧化加濕過程分三個階段進行機理上的研究，這三個階段依次為液膜形成、液膜初次破碎及二次霧化、水與空氣的熱濕交換。
  2. Based on the theory analysis and experiment work, the paper studies the humidifying property of the centrifugal nozzle with firing pin type, high pressure and little aperture. compared with the traditional air washer, the high efficiency and energy saving character of this kind of nozzle is stood out

    課題從理論和試驗兩方面分析研究了撞針型高壓小孔徑離心式噴嘴的霧化加濕性能，並將其與傳統噴水室加濕系統進行能耗比較，突出了撞針型高壓小孔徑離心式噴嘴高效節能的特點。
  3. Through the special studies on impacts to atomizing and humidifying effect from such factors as the firing pin type, centrifugal structure, higher spraying pressure, less aperture, initial water temperature and original state of the air, some conclusions are obtained, such as : the centrifugal nozzle with firing pin type, high pressure and little aperture has bigger air eddy and atomizing angle. the spaying liquid has high velocity. the droplet is small, and the heat and mass transfer velocity is high

    通過對撞針型結構、離心式結構、較高的噴水壓力、較小的噴嘴孔徑、噴水初溫及待加濕空氣初狀態對霧化加濕效果的作用原理的重點分析，得到：撞針型高壓小孔徑離心式噴嘴具有較大的空氣渦與霧化角，噴出的液體流速高、液滴小、水與空氣傳熱傳質速率高，撞針型結構提高了霧化加濕效率，高壓小孔徑的特點為霧化加濕提供了較大的能量，而噴水初溫的升高會減小水的粘性力和表面張力，從而優化加濕效果。
  4. When the water - air ratio increases, air ' s changing quantity of enthalpy and absolute humid will be enhanced. at last, the paper analyses the data from single factor experiment by mathematics method and gets relationship formulas about the nozzle flux, valid humidifying quantity and air ' s enthalpy changing quantity

    最後，對上述單因素試驗得到的數據進行數學分析，運用線性回歸分析、多項式回歸分析和非線性回歸分析的數學方法，得到影響撞針型高壓小孔徑離心式噴嘴的噴嘴流量、有效加濕量和空氣焙變量的數學關系式。
  5. As to the work about experiment study, at first, the paper makes certain the prominent affecting factors to the automating and humidifying property of this kind of nozzle by orthogonal experiment. by jicha analysis method and fangcha analysis method, the paper got that the nozzle aperture, the initial water temperature and the spraying pressure have prominent effect to the humidifying property while the effect of the original air state is small

    試驗工作方面，首先通過正交試驗確定對撞針型高壓小孔徑離心式噴嘴霧化加濕性能影響顯著的因素，運用極差分析法和方差分析法，得到噴嘴孔徑、噴水初溫和噴水壓力對噴嘴的加濕性能影響顯著，而待加濕空氣初狀態的影響相對較小。
  6. The shearing layer is carried by the jet and the eddy is formed because of the instability and selective amplification of shearing layer which will propagate to the downstream. as the eddy impacts the impinging wall, a wave of pressure disturbance with certain frequency is induced. this wave then propagates to the upstream with high speed, and results in the overlap and amplification of the waves when the frequencies of them are close with each other

    當前噴嘴流束中的不穩定擾動波在穿過腔內的剪切層時，剪切層對其有選擇放大作用，形成渦環結構，剪切流動中渦環與碰撞壁撞擊，在碰撞區域產生壓力擾動波並向上游反射，在上游剪切層分離處誘發新的擾動的產生，當新擾動與原擾動匹配時，射流上游就被不斷地受到周期性激勵，腔內就產生流體自激振蕩並在後噴嘴出口形成脈沖射流。
  7. As a simple device without moving parts, vortex tube is composed of nozzle, vortex chamber, separating plate, control valve, hot - end and cold - end

    渦流管是一種結構極為簡單的製冷裝置，它由噴嘴、渦流室、分離孔板、熱閥以及冷熱兩端管組成。
分享友人
分享到 Line

分享到臉書