噴嘴效率 的英文怎麼說

中文拼音 [pēnzuǐxiàolǜ]
噴嘴效率 英文
efficiency; nozzle
  • 噴 : 噴動詞1. （液體等受壓力而射出） spurt; spout; gush; jet 2. （噴灑） spray; sprinkle
  • 嘴 : 名詞1. （口的通稱） mouth 2. （形狀或作用像嘴的東西） anything shaped or functioning like a mouth 3. （指說話） talk; speak
  • 效 : Ⅰ名詞（效果; 功用） effect; efficiency; result Ⅱ動詞1 （仿效） imitate; follow the example of 2 ...
  • 率 : 率名詞（比值） rate; ratio; proportion
  • 效率 : productiveness; efficiency; productivity; workpiece ratio
  1. Moreover, the system of powdered coal conveying with primary air is the most important tache, whether the distribution of primary air is even or not directly relates to whether the distribution of powdered coal is even or not in all firing implement and nozzles, sequentially directly relates to whether it is hard to take fire, whether the fire is stable, whether there is coking and how about the heat efficiency of the boiler, hi addition, if there is jamming and deflagrate in the system of powdered coal conveying with primary air, severe safety accident can be resulted

    良好的煤粉配風是建立合理的爐內空氣動力工況和穩定燃燒的必要條件。而其中一次熱風送粉系統又是最重要的一個環節，一次風配風是否均勻直接關繫到煤粉在各燃燒器和各噴嘴中的分佈是否均勻，從而直接關繫到著火是否困難、火焰是否穩定、局部是否結焦以及鍋爐的熱效率高低。若一次風送粉系統發生堵塞和煤粉爆燃則可能引發嚴重的安全事故。
  2. Through the special studies on impacts to atomizing and humidifying effect from such factors as the firing pin type, centrifugal structure, higher spraying pressure, less aperture, initial water temperature and original state of the air, some conclusions are obtained, such as : the centrifugal nozzle with firing pin type, high pressure and little aperture has bigger air eddy and atomizing angle. the spaying liquid has high velocity. the droplet is small, and the heat and mass transfer velocity is high

    通過對撞針型結構、離心式結構、較高的噴水壓力、較小的噴嘴孔徑、噴水初溫及待加濕空氣初狀態對霧化加濕效果的作用原理的重點分析，得到：撞針型高壓小孔徑離心式噴嘴具有較大的空氣渦與霧化角，噴出的液體流速高、液滴小、水與空氣傳熱傳質速率高，撞針型結構提高了霧化加濕效率，高壓小孔徑的特點為霧化加濕提供了較大的能量，而噴水初溫的升高會減小水的粘性力和表面張力，從而優化加濕效果。
  3. According to the experimental data of droplet size 、 particle spectrum range 、 droplet cone shape 、 flow rate 、 cover area and cover area rate which obtained through changing the pressure of power sprayer and the nozzle diameter in greenhouse ， this paper made comparative analysis on atomizing performance in same pressure and different nozzle type between same nozzle type and different pressure. the conclusion is that : the ejection rate and the droplet cone shape change with the variation of pressure and nozzle diameter ， average particle diameter decreases obviously and particle quantity increases obviously with the increase of pressure and decrease of nozzle diameter. these results will lay experimental foundation for precise spraying 、 low pollution and highly effective operation

    本文根據溫室內動力噴霧機壓力與噴嘴孔徑的變化影響霧滴大小、粒譜范圍、霧錐形狀、流量、覆蓋面積及覆蓋面積率的試驗數據，對相同壓力下不同噴嘴型號和相同噴嘴型號時壓力不同時的微粒化性能進行對比分析和研究，得到如下結論噴出量與霧錐形狀隨著壓力和噴嘴孔徑大小變化而變化；平均粒徑隨著壓力的增加和噴嘴孔徑的減小而明顯減小；粒數隨著壓力的增加和噴嘴孔徑的減小而明顯增多，為精噴量、低污染、高防效的防除作業奠定了實驗基礎。
  4. Its atomized parcel is so small that no drip is separated out. this kind of centrifugal nozzle has high humidifying efficiency and low energy cost, which could be used in many situations in textile factories such as directly humidifying in workshop and humidifying in air pipeline

    撞針型高壓小孔徑離心式噴嘴的霧化粒子細小、無水滴析出、加濕效率高、耗能少，可直接向車間加濕，適用於紡織廠等多種應用場合。
  5. Later, the paper ascertains how the prominent factors influence the humidifying effect by single factor experiment and got such solutions : when other situations do n ' t change, the nozzle flux will enhance with the increase of the nozzle aperture and spraying pressure. air ' s changing quantity of enthalpy and absolute humid, valid humidified quantity, humidifying efficiency and saturation efficiency will enhance with the increase of the initial water temperature. with the enhance of the praying pressure, the valid humidified quantity and air ' s changing quantity of enthalpy will increase first and decrease later, while the humidifying efficiency will drop

    然後通過單因素試驗確定影響顯著的因素如何作用加濕效果，得到：在其他條件不變的情況下，噴嘴流量隨噴嘴孔徑和噴水壓力的升高而增大，空氣焓變量、絕對濕度差、有效加濕量、加濕效率及飽和效率隨噴水初溫的升高而提高，有效加濕量和空氣焓變量隨噴水壓力的升高先增加然後有所下降，而加濕效率隨噴水壓力的升高而下降，焓變量和絕對濕度差隨水氣比的增加而增大。
  6. This paper has analyzed and synthesized the problems of burning heavy viscosity petroleum about injecting steam boilers in liaohe oil field. the heat balance experiments on injecting steam boilers burning heavy viscosity petroleum is made first. the main causes of low thermal efficiency and heat lose of flue gas are the poor effect of atomization and burning with old - fashioned oil nozzles, worse ash gathered on. heat exchange surface and high temperature of flue gas

    本論文在分析綜述了遼河油田注汽鍋爐燃用高粘度稠油時存在的問題的基礎上，首先對燃用稠油的注汽鍋爐進行了正、反熱平衡試驗，分析了注汽爐熱效率偏低、排煙熱損失偏高的主要原因是原噴油嘴改燒高粘度稠油時霧化和燃燒效果差、換熱面積灰嚴重、排煙溫度太高。
  7. Great difference in pressure for two flow made pressure wave system and it help to extend the delay time for gas in chamber, which increases combustion effusion. second, to increase combustion effusion, the inlet temperature of air and gas should be enhanced in the range of heat releasing in chemical reaction. third, the first work condition is unburned absolutely and the second work condition is burnt in shear layer of inlet and the end of down wall zone in straight segment

    對于壓力差很大的兩股氣流，所形成的壓縮波系的結構可以增加燃氣駐留時間，提高燃燒穩定性;為了提高擴散燃燒的效率，在保證能放熱的化學反應溫度范圍之內，應適當提高燃氣及空氣的來流入口溫度;燃氣噴嘴應居於燃燒室軸線上，是改進超音速燃燒室結構的一種思路。
  8. The results showed that the processing parameters ( such as laser power, the diameter of laser, scanning speed of laser beam, ratio of overlapping ) are important to acquire a perfect component. furthermore, in order to assure geometric properties ( accuracy, surface finish ), the structure of the off - axial powder nozzle was improved to avoid the oxidation of the molten pool. the density metal test sample of rene95 high - temperature alloy was made by lsf through optimizing the processing parameters

    本文對激光立體成形的工藝特性進行了深入系統的研究，發現如果要獲得理想的成形效果，就必須對成形過程中的工藝參數進行精密控制，例如激光功率、激光光斑大小、光束掃描速度、搭接率等；同時為了保證成形件有較高的尺寸精度和表面質量，必須對成形零件的氧化問題進行控制，通過改進側向送粉噴嘴的結構設計，成形件的表面氧化問題得到適度控制。
  9. The dehydration time is square of the droplets diameter so the small diameters of the droplets can cut down the drying time then reduce the height of the drying chamber. to the combined spin - flow pressure spray drying, the diameters of droplets are small and the dehydration rate is higher so keeping the qualities of the dried products we can increase the speed of the inlet wind and reduce the temperature of the outlet wind thus can improve the evaporation intensity of the drying chamber and the average energy utilization of the drying equipment

    因霧滴的脫水時間與其直徑的平方成正比，減小液滴直徑有利於縮短乾燥脫水時間，可有效降低乾燥塔的高度；由於旋流式組合壓力噴嘴霧化滴徑的減小，脫水速度明顯加快，在不影響乾燥物料性質的前提下，適當提高進風溫度，同時有效地降低排氣溫度，有利於提高幹燥塔的蒸發強度，也有利於提高幹燥設備的平均能源利用率。
  10. It was found that the ultra - fine powder can flow smoothly in a spouted bed with a draft tube under some sorts of design parameter and operating condition, thus a new effective method to improve fluidization quality of the ultra - fine powders is obtained ; at higher supplied gas velocity, an increase in the solid circulation rate is observed ; the extent of the distance between the nozzle and the draft tube inlet result in the promotion of the solid circulation rate ; the solid circulation rate increase with increasing the draft tube diameter or the bed mass ; the gas bypassing is nearly zero in the present work ; and the solid flow in the annulus is observed as a moving bed

    結果表明：在一定的床層結構和操作條件下，超細粉可以在導向管噴動床中實現平穩流化，從而為改善超細粉的流化質量提供了一種有效的新方法；固體循環速率與噴動氣流量、導向管直徑、導向管底部與噴嘴出口間距以及床層裝填量成正比；氣體則基本上不存在「旁路」現象；環隙區中的顆粒流動表現為一移動床特徵。
  11. Sprays valve and nozzles must be kept in proper alignment and working order to maximize shape efficiency

    必須保持噴油閥和噴油嘴對中和工作順序正確以最大限度地提高板型效率。
  12. The efficiency of nozzle rinsing can be improved as much as 19 % by switching the unequal flow rate of the two head - on rinsing streams after a suitably set first rinsing period has elapsed

    對于噴嘴式洗滌，經由在適當首段洗滌后對調兩不相同流量之入漕洗滌水流流量，可達成洗滌效率19 %之提升。
  13. It will exert resistance and damping force to the torque motor armature, so that the dynamic performance, especially the stability, of flapper - nozzle servo - valve can be improved. the self - excited oscillations and noise can be removed. at the same time, as magnetic fluid has a higher magnetic permeability, the efficiency of torque motor magnetic circuit can be improved

    由於磁流體具有的較大磁導率和較大的磁化強度，把磁流體添加到伺服閥力矩馬達的工作氣隙中，可提高伺服閥力矩馬達的磁迴路效率，增加伺服閥的阻尼，從而改善噴嘴擋板伺服閥的動態特性，抑制及消除其自激振蕩和噪聲。
分享友人
分享到 Line

分享到臉書