噴嘴段 的英文怎麼說

中文拼音 [pēnzuǐduàn]
噴嘴段 英文
nozzle segment
  • 噴 : 噴動詞1. （液體等受壓力而射出） spurt; spout; gush; jet 2. （噴灑） spray; sprinkle
  • 嘴 : 名詞1. （口的通稱） mouth 2. （形狀或作用像嘴的東西） anything shaped or functioning like a mouth 3. （指說話） talk; speak
  • 段 : Ⅰ量詞（部分） section; segment; part; paragraph; passage Ⅱ名詞（姓氏） a surname
  1. As to the work about theory analysis, at first, the paper describes the atomizing and humidifying process of the centrifugal nozzle with firing pin type, high pressure and little aperture and liquid physical properties. later, combining with the structure characters of this kind of nozzle, the paper studies on the theory of the atomizing and humidifying process by three phases, which is water film forming phase, water film falling into pieces phase, and heat and mass transfer between water and air phase in turn

    理論工作方面，首先描述了撞針型高壓小孔徑離心式噴嘴的霧化加濕過程和液體的物理性質，然後結合撞針型高壓小孔徑離心式噴嘴的結構特點，將其霧化加濕過程分三個階段進行機理上的研究，這三個階段依次為液膜形成、液膜初次破碎及二次霧化、水與空氣的熱濕交換。
  2. Focusing on the performance evaluating and the design of tripropellant injector, adopting the cold test rig with background pressure supply, malvem particle analyzer, ccd photography system, tripropellant hot test - bed, numerical simulation software and auxiliary theoretical a nalysis, the d ischarge c haracteristic a s w ell a s a tomization p erformance o f the injector and the combustion performance as well as the mode - transition characteristic of thrust chamber are studied detailedly based on the 3 different structures of coaxial tripropellant injector, large numbers of important conclusions are gained

    本文圍繞三組元噴嘴的性能評定及設計方法。採用反壓冷試臺、馬爾文測粒儀、 ccd高速攝影系統、三組元發動機熱態試驗臺、數值模擬程序及輔助理論分析等多種技術手段和研究方法，對三種結構的同軸式三組元噴嘴深入進行了噴嘴流量特性和霧化特性、推力室燃燒性能和轉工況性能研究，得到了大量重要結果。
  3. The efficiency of nozzle rinsing can be improved as much as 19 % by switching the unequal flow rate of the two head - on rinsing streams after a suitably set first rinsing period has elapsed

    對于噴嘴式洗滌，經由在適當首段洗滌后對調兩不相同流量之入漕洗滌水流流量，可達成洗滌效率19 %之提升。
  4. The influences of the inlet tube angle, backpressure and driving jet velocity on static pressure distribution in the gas - solid injector are calculated, and the effects of the inlet tube angle on particle bulk phase concentration and axial mean speed of particles in the gas - solid injector are analyzed firstly. the predicament caused by lack of measuring means on the particle velocity in experiments is solved

    分析了收縮角、背壓和氣體噴嘴出口速度對氣固噴射器內靜壓分佈的影響，以及收縮角對氣固噴射器內固體顆粒體積濃度場和顆粒平均速度的影響，解決了噴射器內固體顆粒速度試驗測試手段缺乏的困境。
  5. The hot runner series makes the plastics in the hot runner from the nozzle of a plastics injector to the inlet of cavity must be always kept at such a molten state by means of heating that you just pick out the product, there is no need for you to take the condensing stuffs from the injection system as the mould cavity is operated

    說明:熱流道系列用加熱的方法使從注塑機噴嘴到型腔入口為止這一段流道中的塑料一直保持熔融狀態，在開模時只需取出產品，而不必取澆注系統凝料。
  6. Typically the rear zone / zones are set 10 - 20 degrees f ( 6 - 12 degrees c ) cooler than the front zone and nozzle

    通常後段及後面各區段的設定溫度比前段噴嘴的設定溫度低10 - 20 ? （ 6 - 12 ） 。
分享友人
分享到 Line

分享到臉書