噴嘴流通特性 的英文怎麼說

中文拼音 [pēnzuǐliútōngtèxìng]
噴嘴流通特性 英文
nozzle flow characteristic
  • 噴 : 噴動詞1. （液體等受壓力而射出） spurt; spout; gush; jet 2. （噴灑） spray; sprinkle
  • 嘴 : 名詞1. （口的通稱） mouth 2. （形狀或作用像嘴的東西） anything shaped or functioning like a mouth 3. （指說話） talk; speak
  • 流 : Ⅰ動1 （液體移動; 流動） flow 2 （移動不定） drift; move; wander 3 （流傳; 傳播） spread 4 （向壞...
  • 通 : 通量詞（用於動作）
  • 特 : Ⅰ形容詞（特殊; 超出一般） particular; special; exceptional; unusual Ⅱ副詞1 （特別） especially; v...
  • 性 : Ⅰ名詞1 （性格） nature; character; disposition 2 （性能; 性質） property; quality 3 （性別） sex ...
  • 流通 : circulate
  • 特性 : characteristic（s）; character; performance; features; properties; behaviour; response; character...
  1. Through the special studies on impacts to atomizing and humidifying effect from such factors as the firing pin type, centrifugal structure, higher spraying pressure, less aperture, initial water temperature and original state of the air, some conclusions are obtained, such as : the centrifugal nozzle with firing pin type, high pressure and little aperture has bigger air eddy and atomizing angle. the spaying liquid has high velocity. the droplet is small, and the heat and mass transfer velocity is high

    通過對撞針型結構、離心式結構、較高的噴水壓力、較小的噴嘴孔徑、噴水初溫及待加濕空氣初狀態對霧化加濕效果的作用原理的重點分析，得到：撞針型高壓小孔徑離心式噴嘴具有較大的空氣渦與霧化角，噴出的液體流速高、液滴小、水與空氣傳熱傳質速率高，撞針型結構提高了霧化加濕效率，高壓小孔徑的特點為霧化加濕提供了較大的能量，而噴水初溫的升高會減小水的粘性力和表面張力，從而優化加濕效果。
  2. Ultrasonic has being attracted much attention gradually in fuel atomization because of some specialities of cavitation and infection on liquid flow. in the course of atomization of pitchy oil, especially, does it show greatly its advantage, but its material atomizational mechanism need research ulteriorly. the primary content of this thesis is about adding cantilever reed to effervescent atomizer so as to combine ultrasonic and effervescent. this thesis has discussed ultrasonic some mechanism, ultrasonic dynamical procreator, effervescent and liquid mucosity infection on atomization, at the some time we make some experiments and discuss atomization rule following some machinery parameter and run parameter so as to find some rule about ultrasonic atomization and to rich the research of ultrasonic atomization mechanism. all that will be beneficial to the design about ultrasonic atomization atomizer

    超聲波由於其空化機理及對液體的流變性影響等特性，在燃油霧化燃燒中逐步引起人們的重視，尤其在重渣油等高粘度液體的霧化過程中逐步顯示出其優越性，但其具體的霧化機理還需要做進一步的研究在氣泡霧化噴嘴基礎加入懸臂式簧片哨，將超聲波與氣泡霧化相結合是本文討論的主要內容本文從研究超聲波的一些機理入手，討論了超聲動力發生器氣泡霧化以及液體粘度對霧化質量的影響，並通過具體的實驗，根據實驗數據來討論霧化質量隨各種結構參數運行參數的變化規律，以便找到超聲霧化的一些規律，豐富對超聲霧化機理的研究，對超聲霧化噴嘴的設計具有一定的指導意義。
  3. The spray processes of throttling and normal pintle nozzles are investigated in this paper. the test results show that the better spray characteristics and spray quality can be achieved when the throttling pintle nozzle is used in small diesel engines

    本文對節流軸針式和普通軸針式噴油嘴的噴油過程進行實驗研究，試驗結果表明，節流軸針式噴油嘴應用在小缸徑柴油機上能取得良好的噴油特性和噴霧質量。
  4. Using compressed air and transformer oil as working substance, this paper studied the pressure characteristic of internal - mixing nozzle and acquired the experimental relation on the pressure in the mixing chamber of internal - mixing nozzle against the operation parameters and structure parameters according to the method of step by step regression

    摘要以壓縮空氣和變壓器油為工質對內混式介質霧化油噴嘴的流量特性進行實驗研究，並通過逐步回歸分析的方法獲得了內混式介質霧化噴嘴油、氣流量系數與運行及結構參數的實驗關系式，可供設計使用部門參考。
  5. A very special rotating cavity with micro - turbine ( de - swirl nozzles ) was applied to investigate the flow characteristics inside the cavity under three mid rotating speeds

    摘要通過實驗對中等轉速下帶有微型渦輪（反預旋噴嘴）的旋轉渦輪盤腔內流動特性進行了系統研究。
  6. In this dissertation, the author summed up the muti - technique in fluid dynamics, heat and mass transferring, mechanical designing and computational technique and studied the conventional pressure spray dryers with different air disperse structure and outlet equipment, at last put forward the theme i. e. the study on combined spin - flow pressure spray drying technology, the main contents were as follows : ( 1 ) the combined spin - flow pressure nozzle was designed whose novel structure has no report at present, and the structural designing parameters were obtained through analyzing the physical characteristic of materials and distribution of particles

    本文總結了國內外在壓力噴霧乾燥裝置的研究應用狀況，並分析了現有噴霧乾燥裝置設計方面的優缺點，運用流體力學、空氣動力學、傳熱傳質學、機械設計和計算機技術等多學科知識，綜合研究了傳統壓力噴霧乾燥系統的單噴嘴霧化裝置在併流、逆流以及混流乾燥中的應用和噴霧乾燥塔的不同布風裝置以及出風裝置的設置情況等，提出了新型旋流式組合壓力噴霧乾燥技術並對此進行了研究，其主要內容包括： （ 1 ）本文創造性地設計出旋流式組合壓力噴嘴的基本結構，並通過對料液的物化特性研究分析以及顆粒度的分佈要求，給出了噴嘴的不同結構設計參數。
  7. Nozzle flow characteristic

    噴嘴流通特性
分享友人
分享到 Line

分享到臉書