嚙入 的英文怎麼說

中文拼音 [nièrù]
嚙入 英文
a roach action
  • 嚙 : 動詞[書面語]1. （鼠、兔等用牙啃或咬） gnaw （at） 2. （侵蝕） erode
  • 入 : Ⅰ動詞1 （進來或進去） enter 2 （參加） join; be admitted into; become a member of 3 （合乎） conf...
  1. The paper studies the surface geometry of globoidal indexing cam by applying the theory of conjugate surfaces and the method of coordinate transformation, presents the equations related to the main inducement curvature of the cam profiles, analysis and deduces the equations of two circumscription curves, which judge if the conjugate surface could mesh properly. some calculate examples and conclusion are given. the surface equation of the globoidal cam and conjugate equation are established

    論文首先在分析空間嚙合原理基礎上，採用坐標變換法推導出弧面分度凸輪的工作廓面方程、嚙合方程和壓力角計算公式，對弧面分度凸輪的嚙合特性進行了深入的分析和研究，對判斷曲面能否正確嚙合的依據如兩類界限線方程以及誘導主曲率等進行推導，並給出算例。
  2. By taking advantage of computer technology the main parts of the reducer - epicycloid groove, hypocycloid groove, steel ball and output mechanism are shown and emulated. the motion of the drive is also demonstrated. the paper mainly concludes the following works : at first, the meshing efficiency of the drive is studied and analyzed in theory according to the constituted construction and the drive principles

    在對其傳動原理及結構進行分析的基礎上，對該傳動的嚙合效率進行了深入研究，並針對該傳動的整體尺寸進行了參數模糊可靠性優化，進而利用計算機技術，對該傳動的主要零件? ?內、外擺線盤和等速輸出機構進行了三維建模模擬，演示了該傳動的運動情況。
  3. At the same time, the system vibration also made the paired gears enter into meshing in advance or and seceding of a couple of laggingly

    同時，系統振動還使嚙合齒對提前或遲后進入嚙合、提前或遲後退出嚙合。
  4. Handling dead or trapped rodents with bare hands ; cleaning or entering closed, rarely used rodent infested structures ; disturbing rodent excreta or nests ; keeping captive wild rodents as pets ; handling equipment or machinery that has been in storage, leaning animal shelter area, hand plowing or planting ; sleeping or camping on the ground, and living in a home with an increased density of mice in or around the home

    徒手處理受困嚙類動物或其屍體清理及進入嚙類動物寄居之地方擾亂嚙類動物的巢穴或接觸其排泄物飼養野生的嚙類動物作為寵物處理放置於嚙類動物出沒巢穴的器具徒手種植躺野地與及居住在嚙類動物頻密出沒的地方。
  5. These designing parameters include stiffness of epicyclical bearings, synthetic meshing stiffness of gears, stiffness of supporting bearing of out put shaft, mass of inner rack, meshing angle of gears, distance between inputting shaft and supporting shaft and input speed etc. according to these analyses, the possible way for improving the dynamic function of three - ring transmission may be put forward

    這些設計參數包括：行星軸承剛度、齒輪綜合嚙合剛度、輸出軸支承軸承剛度、內齒板質量、齒輪嚙合角、輸入軸和支承軸間距及輸入轉速等，根據這些分析，可以提出改善三環傳動動態性能的可能途徑。
  6. An automated de - noising algorithm based on the energy of wavelet packet not donoho ' s threshold algorithm is established. a gear feature vibration signal extraction method using the wavelet packet energy is proposed, which can separate gear meshing vibration, noise vibration and gear fault vibration signal from the original gearbox case vibration signal. basis pursuit ( bp ) algorithm is introduced into the filed of mechanical signal de - noising and feature extraction for the first time

    第三章擺脫了donoho的閾值消噪思想，從能量的角度建立了基於小波包的自動消噪演算法；提出基於小波包能量分佈的齒輪故障特徵信號提取方法，可以將齒輪嚙合振動信號、干擾振動信號以及故障沖擊振動信號從原始齒輪振動信號中分離出來；首次將基追蹤消噪演算法引入到機械故障信號的消噪與特徵提取上，通過對齒輪故障信號的消噪，表明了它的有效性，並對影響該方法實際應用效果的因素進行了全面的分析，同時也指出了該方法存在的局限性。
  7. 2. the flux characteristics of ordinary helical gear pump are lucubrated by theory for the first time, on this condition the selective qualification of the helical gear pump is gained

    首次對普通斜齒齒輪泵流量特性進行了深入的理論研究，在此基礎上研究了全齒廓嚙合斜齒齒輪泵流量特性，首次得到了完全消除斜齒齒輪泵流量脈動的螺旋角的選擇條件。
  8. Creative points and all tasks having be finished are briefly shown below : according to the classical space meshing theory, we have strictly deduced a series of formulae such as the equation of contacting line of worm, the equation of the second limiting curve of worm gear, and the equation of working surface and non - working surface, etc. and we have deeply studied the algorism of the actual contacting lines of worm gear drive

    本文的主要創新點和成果如下：基於經典共軛嚙合理論，對平面二包蝸桿副的運動關系進行了嚴密分析，獲得了蝸桿副齒面方程、蝸桿齒面一界曲線方程、蝸輪齒面二界曲線方程等一系列齒面分析所必須的數學公式，並深入研究了蝸桿副齒面接觸線的演算法，為蝸桿副的三維數字化造型打下了堅實的數學基礎。
  9. Equations of mesh, shorting contact line, undercutting limit line, meshing limit lines and the existence conditions, angle between the direction of relative speed and the direction of contact line, induced normal curvature about every point on the contact line are established. moreover, the paper also theoretically analyzed the error of the grinded gear surface. on the basis of the theory, the computer program is worked out to automatically produce the contact line and the boundary curves of mesh. analysis of meshing circs under different parameters can be done so that we can gain the best process condition

    首先對漸開面二次包絡理論進行了深入的探討，推導出了兩次嚙合的嚙合方程式、瞬時接觸線方程式、根切界限線方程式、嚙合界限線的方程式及其存在條件，相對運動速度方向與接觸線方向的夾角及接觸線上各點的誘導法曲率；此外，還對磨齒后工件的齒面誤差進行了理論分析；並在理論基礎上編制了相應的計算機程序，自動生成接觸線族及嚙合界限線，對不同參數條件下的嚙合情況進行分析，可以使工藝條件達到最佳狀態；最後研究了磨齒裝置，設計了磨齒機的傳動系統。
  10. Detecting methods for leptospira in imported rodents

    輸入性嚙齒動物攜帶鉤端螺旋體的檢測方法
  11. We proposed four kind of it and analyzed their structure. this kind of new actuating mechanism can realize the going around a turn under the condition of steady and smoothing, so it can realize the transmission continuous and long distance round about movement with the whole equipment

    同時，為了使該機構能夠實現正常的曲線嚙合，在漸開線柱齒鼓形齒輪和空間齒條機構之中引入了一個導引機構，並對其進行了結構設計和樣機製造，從而使這種空間齒輪齒條機構實現了平穩的空間曲線嚙合傳動。
  12. Using method of modes accumulation and continuity of displacements and velocities of components in mesh stiffness change, system vibration was calculated

    採用模態疊加法和系統在輪齒嚙入及嚙出時位移和速度連續的條件，獲得系統動響應。
  13. The third, the vibration theory of chord is applied to establish the model of the ramming system. the chain organ ' s polygon effect and it s meshing impact are involved in the model. the transverse vibration of the ramming system is analysed for the solution

    運用弦振動理論建立了描述供彈機橫向振動的理論模型，計及了鏈傳動機構固有的多邊形效應和嚙入嚙出沖擊效應，計算獲得了方程的數值解，描述了該機構的橫向振動特性。
  14. The contact deformation at transient engaging point is derived from deeply analyzing geometric property and kinematics relationship between the two action flanks by use of engagement principle, differential geometry, elastic and plastic mechanics, etc

    運用嚙合原理、微分幾何和彈塑性力學等基礎知識，對齒面間的幾何性質和運動關系進行深入細致的分析研究，計算各瞬態嚙合點的接觸變形。
  15. Firstly, the paper introduces the development and application of computer graphics & image technique, discusses the principle and method of cg and digital image processing, such as matrix of the graphic transformation, homogeneous reference frame, sampling and quantization of the image, file format of the image, template operation, etc. secondly the paper introduces the purpose and method of image enhancement processing, explains the each occasion of those methods such as threshold transformation, smoothing processing, sharpening processing, analyzes and contrasts the processing results of object image. thirdly, the paper introduces the method of mathematics morphologic, edge detection and thinning processing, attains character description of image and character dots of the contour. fourthly, the paper processes the coordinate transformation to character dots and basic splines fitting, imports correlative condition to devise meshing line and meshing track

    本文首先介紹了計算機圖形圖像技術的發展與應用情況，對計算機圖形學和數字圖像處理的一些基本理論和方法如圖形變換矩陣、齊次坐標系、圖像采樣和量化、圖像文件格式、模板操作等內容進行了討論：然後對圖像增強處理的目的和方法進行了介紹，對諸如閥值變換、平滑處理、銳化處理等方法的應用場合進行了說明，並對實物圖像的處理結果進行了分析與比較；接下來介紹了數學形態學方法、對增強后的圖像進行邊緣檢測的方法和圖像的特徵描述方法，並獲取輪廓的特徵點：隨后對獲取的特徵點進行坐標變換，並進行b樣條曲線擬合，引入相關條件生成齒輪副的嚙合線及嚙合軌跡：最後引入等值線和區域填充表示方法，並以等值線和區域填充的形式對弧齒錐齒輪嚙合模擬的載荷分佈情況進行了直觀的表示。
  16. By means of researching the meshing impact in the engagement of standard chain respectively with the spur toothed sprocket and the involute toothed sprocket, it has been discovered through analysis that by adopting the involute tooth for the sprocket could reduce the normal impact velocity in the engaging instant of chain and sprocket, thus lowered the meshing impact among chain and sprocket

    通過研究標準鏈條分別與直齒鏈輪和漸開線齒鏈輪嚙合的嚙合沖擊，分析發現在鏈輪上採用漸開線齒能減小鏈條與鏈輪嚙合瞬間的法向沖擊速度，進而降低鏈條與鏈輪的嚙入沖擊。
  17. Several factors affecting the crushing cavity design were analysed and modification was made on the design theory for the biggest tooth angle of crushing cavity. problems in the design of domestic crusher cavity were pointed out and a rational cavity shape was given. its application in several mines has achieved satisfactory results

    分析了影響破碎腔設計的幾個因素，對破碎腔最大嚙角的設計理論提出了修正，指出國內破碎機破碎腔的問題所在，給出了合理的腔形，並在幾個礦山投入使用，取得了滿意的效果。
  18. It means that the maximum friction force is at the positions of neither the approach nor the recess point, which is an original conclusion of this paper

    這就意味著最大摩擦力並非出現在嚙入點和嚙出點，這是本文具有創新意義的一個結論。
  19. In odontoid chain drive, the chain bears a periodical alternating load, in which the impact load produced while the link meshes into the tooth of sprocket makes comparatively big effect

    摘要在齒形鏈傳動中，鏈條承受周期性的交變載荷，其中鏈節嚙入輪齒時產生的沖擊載荷影響較大。
  20. Translation modes are similarly independent of the rotational support stiffnesses. large contact ratio do not mean lower mesh force. if either the number of sun or ring gear is not multiple of planet gear, system will run effectively, with lower impaction of tooth mesh in and out

    研究表明：扭轉支撐剛度的變化影響系統的轉動模態，徑向支撐剛度（行星架的除外）的變化影響系統的位移模態；齒輪間重合度大並不等於輪齒間的受力情況好；行星輪與內齒圈齒數不為行星輪個數的整數被時，輪齒的嚙入、嚙出對系統的沖擊小，系統的效率高。
分享友人
分享到 Line

分享到臉書