嚙合器 的英文怎麼說

中文拼音 [niègěqì]
嚙合器 英文
engage switch
  • 嚙 : 動詞[書面語]1. （鼠、兔等用牙啃或咬） gnaw （at） 2. （侵蝕） erode
  • 合 : 合量詞（容量單位） ge, a unit of dry measure for grain （=1 decilitre）
  • 器 : 名詞1. （器具） implement; utensil; ware 2. （器官） organ 3. （度量; 才能） capacity; talent 4. （姓氏） a surname
  1. The two cog - wheels engaged and the machine started

    那兩個齒輪一嚙合，機器就啟動了
  2. Based on the comprehensive estimating method of the final drive, the analysis method is proposed to focus on analyzing one of the important testing targets ? the meshing states of the spiral bevel gears and differential gears of the final drive when they are working under the imitating conditions

    本文主要對汽車后橋主減速器殼表面的振動信號進行分析。這是在主減速器綜合評價方法的基礎上，針對其中一項重要的試驗參數? ?主減速器齒輪的嚙合狀況，而提出的分析方法。
  3. Spur geared wheel reductor

    外嚙合圓柱齒輪式輪邊減速器
  4. Size and obliquity of tooth directly influence clutch whether normal operating. it is a key part for ensuring normal operating of aira too. this article fully deduces their compute formula

    該齒形的大小、傾角直接影響離合器是否能正確地嚙合和分離，也是保證機構進行正確工作的關鍵部分，本文詳盡推導了它們的計算公式。
  5. ( 3 ) in the condition of invariable instantaneous speed ratio, the equations of teeth surface of all key components, such as end face gear, oscillating teeth, wave producer, et al, are deduced

    （ 3 ）在保證瞬時傳動比恆定的條件下，由空間嚙合原理出發，重點推導了活齒端面諧波齒輪傳動裝置的主要傳動部件? ?端面齒輪、活齒以及波發生器端面凸輪的齒面方程。
  6. By analyzing phase angle of meshing geometric drawing position, the theoretical formula of cycloid gear actual operating space of cycloid planetary gear speed reducer is driven, at the same time, fitting a curve, and discussing engineering significance of function curve to combine reality

    摘要通過分析嚙合相位角幾何圖形的位置，推導出擺線針輪行星減速器中擺線輪實際工作范圍的理論公式，畫出了嚙合相位角函數的擬合曲線，並結合實際討論其函數曲線的工程意義。
  7. To sum up, the thesis mainly anaylses the performance of the aviation retarder spiral bevel gear in meshing, which results provide experiment for the design and improvement of the spiral bevel gear

    總之，本文主要對航空減速器螺旋錐齒輪嚙合過程中的齒輪的嚙合性能進行了分析研究，所得結論為螺旋錐齒輪副的設計和改進提供依據。
  8. Dqj point - line meshing gear reducers

    Dqj點線嚙合齒輪減速器
  9. The two cogwheels engaged and the machine started.

    那兩個齒輪一嚙合，機器就啟動了。
  10. Of a selector, a moving contact that engages with the contacts of a bank

    與存儲單元的觸點相嚙合的選擇器滑動觸點。
  11. The design methods, such as the theory of mechanism dynamic design, the finite element method and the theory of fuzzy reliability etc, are introduced to study the vibration and structural parameters optimization design of the swing movable teeth drive system. the dissertation includes the following six aspects : a ), the torsional vibration dynamic model of swing movable teeth transmission system ; b ). the torsional and flexural vibrations dynamic analyzing model of swing movable teeth drive ; c )

    研究的內容包括以下六個方面： a ）擺動活齒減速器傳動系統扭轉振動的動力學建模； b ）擺動活齒減速器傳動系統彎、扭耦合振動的動力學分析建模； c ）擺動活齒減速器箱體振動的有限元模態分析； d ）擺動活齒減速器高速軸的抗共振模糊可靠性設計； e ）結構參數對活齒傳動嚙合剛度的影響； f ）擺動活齒傳動的模糊可靠性優化設計。
  12. When you disengage the clutch, all gears are at rest and no power is transmitted to the drive wheels, however, when you move one of the sliding gears, such as c, into mesh with d, then by engaging the clutch, you complete the connection between the engine and the drive wheels

    當松開離合器時，所有的齒輪都不再運動，也沒有力傳給驅動輪，然而，當你移動一組變速齒輪時，如將c與d嚙合，然後踩離合器，這樣就使得發動機與驅動輪相接。
  13. Connectors for electronic equipment - tests and measurements - part 13 - 1 : mechanical operating tests - test 13a : engaging and separating forces

    電子設備連接器.試驗和測量.第13 - 1部分:機械操作試驗.試驗13a :嚙合力及離散力
  14. This paper put forward a new type backstop that transfer the backstop moment by the meshing components, and completed the design of the backstop

    本文提出了一種新型的由嚙合元件傳遞逆止力矩的嚙合式非接觸逆止器，並完成了逆止器的設計。
  15. From the analysis, the angle between the axes of the annular gear and outer profile of the coupling in its steady mesh was derived, and a general method for determining the angle was obtained by using an equilibrium of the forces and couples exerting on the annular gear, from which the vibrational features of the coupling could be revealed

    得出齒式聯軸器聯接不對中的穩定嚙合時內齒環軸線與外齒環軸線間的空間位置關系，以及用內齒環的力和力偶平衡的方法來求其軸線間夾角的一般方法，並得出了齒式聯軸器聯接不對中故障所具有的一些振動特徵。
  16. The paper presents and improved structure as well as a fuzzy reliable optimal design method mainly for gear parameters of planet reducer with fewer tooth difference in a certain blow molding system, according to the analysis on fault of the original type

    摘要通過對某一吹塑系統少齒差行星減速器的故障分析，提出了相應的改進措施外，更重要的是對少齒差行星減速器的嚙合參數進行了模糊可靠性優化設計。
  17. Finite element analysis of the multi - tooth meshing effect of three - ring gear reducer

    三環減速器多齒嚙合效應的有限元分析
  18. When bears enough loading, actual contact tooth number will exceed theoretic contact tooth number, which makes the loading capacity of the gears increased dramatically

    三環傳動在足夠大的載荷作用下，實際嚙合齒數會大於理論嚙合齒數，使得三環減速器中齒輪副的承載能力大大提高。
  19. Three - dimensional flow field analysis of paratactic element in non - intermeshing twin screw reactor

    雙螺桿反應器非嚙合併列型螺紋元件流場數值模擬
  20. On the base of achievements of predecessors, this thesis use a new research method - adams software. using the software, i built simulating model of 3s clutch, and study the engaging and disengaging of 3s clutch during codog translating process. combined with experimental results, i make deeper research, and make some achievements

    在以往研究成果的基礎上，本文採用了新的研究方法，用先進的動力學模擬軟體? ? adams軟體，建立了3s離合器的模擬模型，對codog切換過程中3s離合器的嚙合和脫開過程進行了模擬研究，與實驗結果結合起來后進行了深入的分析，取得了一些成果。
分享友人
分享到 Line

分享到臉書