圓柱中心線 的英文怎麼說

中文拼音 [yuánzhùzhōngxīnxiàn]
圓柱中心線 英文
cylindrical centerline
  • 線 : 名詞1 （用絲、棉、金屬等製成的細長的東西） thread; string; wire 2 [數學] （一個點任意移動所構成的...
  1. As both the meshing point and ball ' s center are on the given cylinder, a general method for developing the cam ' s profile is studied. it is proved that the profile of positive and negative transmission is unique if the face gear, the difference between face tooth number and ball number and the diameter of ball are the same. the concrete expression of meshing cam on given spatial cycloid profile, and the characteristics of the profiles are discussed

    論文的主要工作包括： 1 、根據嚙合點和鋼球中心軌跡均在同一圓柱面上的特點，研究了給定端齒齒廓條件下求解凸輪齒廓的一般方法；論證了在給定端齒、齒差數和鋼球直徑相同的條件下，正負齒差嚙合齒廓的唯一性；討論了端齒為球面擺線時，凸輪齒廓的具體表達式，並研究了該齒廓的性質。
  2. Using the vector potential, the expression for calculating inductance of air - cored solenoid coil is derived in the dissertation. and the calculating methods of function t in the calculating expression are given for the convenience of the calculation of inductance while the precision is not strictly requested

    利用矢量磁位a直接推導出了通電空心圓柱線圈電感的計算表達式，給出了求解計算式中函數t的計算方法，以方便精度要求不高時的電感計算。
  3. Connectors for electronic equipment - product requirements - part 1 : generic specification iec 61076 - 1 : 2006 ; german version en 61076 - 1 : 2006

    圓柱輪-檢驗實施規范-第3部分:輪坯軸中心距和軸線平行度
  4. The curvature interference of the gear and the influence of radius of the mill - cutter, axial misalignment, and center distance on meshing are analyzed. based on these analyses, propose two methods to achieve point - contact : to change the radius of the mill - cutter and increase the center distance

    在分析了弧齒線圓柱齒輪的嚙合傳動不產生曲率干涉的條件和刀盤展成半徑、軸線平行度誤差、中心距對嚙合影響的基礎上，提出了點接觸弧齒線圓柱齒輪實現的兩種方案:調整刀盤展成半徑和增大中心距。
  5. Air - cored solenoid coil is applied widely to the regions such as electron, electrical engineering and radio technique

    空心圓柱線圈在電子、電氣、無線電等領域中有著廣泛的應用。
  6. By solving an inverse heat conduction problem, one method is developed for the estimation of the temperature of a hot wire embedded at the center of a cylinder based on infrared temperature - measuring

    摘要利用紅外測溫技術，結合導熱反問題求解，給出了一種根據加熱圓柱體外壁溫度紅外監測反推圓柱體中心軸線上熱導線溫度的方法。
  7. The software can design many conventional type of cam, concluding cam - plate with middle follower, cam - plate with offset follower, cylindrical cam, dividing cylindrical cam, and cylindrical cam with space curve, etc. in forming working curves of cam - plate, used the approximation by arcs which can lessen the nodal points on curves of cam uttermostly in same error, so it reduce the computation time and relieve the chattering of principal axis. in former times, to cam mechanism, the follower only has one direction motion

    本軟體可以設計的凸輪類型較多，包括了對心移動從動件盤形凸輪、偏置移動從動件盤形凸輪、圓柱凸輪、圓柱分度凸輪和空間曲線柱形凸輪等，其中對盤形凸輪的工作曲線採用了難度較大的圓弧逼近演算法和等誤差演算法，這樣就可以在相同的允許誤差內最大限度的減少生成曲線的節點數，減少計算時間，同時可以大大減輕加工中的振動現象。
  8. In this case, the line - projecting cylinder is the fundamental nature of the character - the character ' s substance

    在這個設計中，那些可以射出直線的圓柱體就是最基本的角色? ?也就是角色在核心規則中的體現。
  9. Cylindrical gears - code of inspection practice - part 3 : recommendations relative to gear blanks, shaft centre distance and parallelism of axes

    圓柱齒輪檢驗實施規范第3部分:齒輪坯軸中心距和軸線平行度
  10. In the calculating example of model inversion, the proper sampling interval and ' trend - band ' method were selected and inversion errors of the linear density and axes depth of cylinder were close to 0. 25 % and 3. 8 %, respectively

    在模型反演算例中，選擇了適當的采樣間隔和「趨勢鑲邊」法，反演的圓柱體線密度和軸心深度誤差分別為0 . 25 %和3 . 8 % 。
  11. The central content of this thesis is theoretic and experimental analysis on involute cylinder worm gear under the coupling of the load and the mounting errors

    本文的中心內容是漸開線圓柱蝸桿承載嚙合理論與實驗分析。為此，論文在以下幾個方面開展研究。
分享友人
分享到 Line

分享到臉書