圓柱狀體 的英文怎麼說

中文拼音 [yuánzhùzhuàngtǐ]
圓柱狀體 英文
cylinder
  • 狀 : Ⅰ名詞1 （形狀） form; shape 2 （情況） state; condition; situation; circumstances 3 （陳述事件或...
  • 體 : 體構詞成分。
  1. This gland is located on the distal end of spermatophore cyst, and shaped like a semicylinder which consists of many acini

    促雄性腺位於精莢囊末端，半圓柱狀，由許多腺泡組成，細胞內富含粗面內質網和高爾基氏體，推測其分泌蛋白質性質的激素。
  2. In the course of working, ， the plow will make use of the shuttling method so that it can dig alternately either on the left or on the right. compared to the unilateral plow, it can improve the productivity because it can help leave off the soil 、 take from the consumed energy and reduce the empty journey. to meet the requests above, we will use a remote cylinder with both a small cubage and double functions, approximately designing the plow to be columniform and symmetric. after the experiment for a period in the field, we found that the most frayed areas had happened at the places of both plow shank and share and at the same time the base of the remote cylinder had ruptured suddenly

    與單向犁相比，其優點在於：耕地無開、閉壟，地表平整，降低了耕后整地的能量消耗，減少了地頭的空行程，因而大大提高班次生產率。為了滿足犁體梭式作業的要求，我們採用了一隻小容積雙作用的液壓油缸；同時對犁壁曲面的形狀採用了近似圓柱形的對稱設計。但經過一段時間的田間試驗，我們發現：該犁犁胸部分的犁脛和犁鏵上的犁尖在工作中磨損較為嚴重；主犁梁和油缸缸體的連接部分（即油缸底座）突然發生了斷裂，造成整個犁體無法正常工作。
  3. Solid model of the involute worm gearing solid model with drive ratio 1 / 50 is built by using ideas - 5. 0, then the elastic contact analysis is proceeded on the basis of contact fem. the dynamic evolution image of the area of the contact zone, the load sharing among instantaneous meshing tooth pairs, the distribution of the contact force, and tooth stress are obtained. 3

    通過漸開線圓柱蝸桿、蝸輪的齒面方程式，利用ideas - 5 . 0軟體建立了傳動比為1 / 50的漸開線圓柱蝸桿傳動的實體幾何模型，在此基礎上應用接觸有限元方法對該傳動進行了彈性接觸分析，包括接觸區的形狀、位置、載荷在瞬時嚙合齒對的分配狀況； 3
  4. Fig. 1 - 1 a, straight ( rectangular ) tourniquets fit optimally on cylindrical limbs. b, curved tourniquets best fit conical limbs. ( from pedowitz ra, gershuni dh, botte mj, et al : clin orthop 287 : 237, 1993

    圖1 1a直（長方形）止血帶最適合用於柱狀的肢體。 b弧形止血帶適用於圓錐形的肢體。
  5. Firstly, the hertz contact theory is used to design the export moment of the prototype ; deformation status of the flexspine under the elliptical cam wave generator action is analyzed using the column shell theory, whose boundary condition is four force action. design proposal of the wave producer put forward considering the precision theory of rolling friction transmission

    首先用赫茲接觸理論對樣機的輸出力矩進行了設計;應用四力作用下的光滑圓柱殼體理論分析了在橢圓凸輪波發生器作用下柔輪的變形狀況，結合滾動摩擦副傳動精度理論提出了波發生器總體設計方案。
  6. Optimum shape of cylindrical solenoid magnet

    圓柱型螺線管磁體的最佳形狀
  7. Comparing with the traditional tensile test instrument of textile. the new testing instrument of longitudinal tensile simulates the conduit condition of the vascular prosthesis in vivo, so it is suitable for the test of longitudinal tensile mechanic properties of vascular prosthesis

    相對于傳統的紡織品的拉伸測試裝置來說，新設計的針對人造血管的軸向拉伸性能的測試裝置模擬人造血管在體內的圓柱體管道的狀態。
  8. This paper founds mathematical model of twin - floater ocean wave generate electricity device, and analyzes primary parameters on the base of mathematical model for searching the optimal solution during designing this electricity device. it presents the method calculating the ocean wave forces on the several ideal floaters such as cube, vertical cylinder, horizontal cylinder, sphere by the theory that froude - krylow presupposition calculates a big diving body

    在研究浮子幾何形狀與浮子所受波浪力的關系的過程中，本文利用弗汝德-克雷洛夫假定法計算大尺度潛體上的波浪力的思想理論來推導作用在幾種常見理想浮體：長方體、垂直圓柱體、水平圓柱體和球體上的垂直波浪力。
  9. The cylindrical structure can be used to accelerate volume rendering using space leaping, the algorithm can achieve a better navigation of real - time

    對于生成圓柱狀結構，採用空間跳躍的體繪制方法進行加速繪制，進一步提高了漫遊的實時性。
  10. A hollow cylinder or tube used to conduct a liquid, gas, or finely divided solid

    管子，導管，輸送管用來輸導液體、氣體或固體細末的管狀中空圓柱體
  11. To study the acoustic unsteady combustion of srm, built the acoustic model of chamber. deduced the little amplitude sound wave 3d equation, used the finite volume discrete method to simulate. got the vibration model of three kinds of chamber

    為研究固體火箭發動機聲不穩定燃燒特性，建立了燃燒室內聲學特性分析的物理數學模型，推導了小振幅聲波三維波動方程，採用有限體積離散方法進行模擬，得到圓柱型、四片翼柱彤和五片翼柱型藥柱三種燃燒室形狀聲學振動基本模態
  12. With the different loading ratio of parallel to axis and normal to axis direction, damage defects will occur bulking problem. by varying the degree of material anisotropy relative to the loading axis such as poisson ' s ratio and shear modulus, crack growth bulking strain value parallel to or normal to the loading axis is different. the parameters controlling the growth or arrest of the delamination damage are identified as the geometry and the depth of defects and radius of cylindrical etc. at last, it was investigated that the delamination damage is often induced by the tip of matrix damage under higher stress

    研究結果表明:殼體筒段受軸向拉伸和內壓載荷作用時，軸向和環向載荷的比率不同，母層和子層可能發生拉伸屈曲，也可能發生收縮屈曲，或者同時發生拉伸和壓縮屈曲;母層與子層各向異性存在差異，即泊松比與剪切模量不匹配時，將使子層板的邊界上承受壓縮和剪切作用，當分層達到臨界狀態則發生屈曲，當母層與子層的各向異性差異越大，則發生分層屈曲的可能性越大;分層損傷的屈曲應變值與子層自身的彈性模量、分層子層的形狀、厚度以及圓柱半徑等因素有關。
  13. Firstly, an estimation algorithm for spectrum of the ct system is presented in the paper by using a standard cylinder or wedge phantom, where the mass attenuation coefficient of the contained material of the phantom is not necessarily to be known

    本文首先給出了由標準均勻圓柱狀模體或楔狀模體估計ct系統的x射線能譜的演算法，該演算法不必已知構成模體的物質關于不同能量的光子的質量衰減系數。
  14. According to the virtual endoscopy automatic navigation, using the two - distance field - based 3d center path finding algorithm to find the path, adopting the cylindrical approximation of tubular organs to replace the center path by several approximate cylinders, while using distance transformation that is substituted by euclidean distance to calculate the approximate cylinder ' s axis and radius, the algorithm can save much time

    摘要針對虛擬內窺鏡自動漫遊技術，利用基於雙距離場的三維中心路徑提取演算法進行路徑提取，採用管狀器官的圓柱狀近似，將中心路徑用多個近似的圓柱體代替，用距離變換代替歐式距離公式計算近似圓柱體的軸和半徑，節省了大量的計算時間。
  15. Stress distribution at cross section of transverse uniformly distributed load and non - uniformly distributed load applied to concrete cylinder by finite element method is analyzed

    摘要採用有限元的方法計算分析了混凝土圓柱體在受橫向均勻線荷載和非均勻線荷載時其橫截面上的應力狀況。
  16. Ansys finite element analysis software is applied for simulating the temperature field of the paraffin and the copper. the time needed of the cylindrical paraffin and the cylindrical copper reaching the thermal equilibrium is calculated respectively, and compared with the experimental data

    使用ansys有限元分析軟體，分別對石蠟和銅受熱時內部溫度場分佈進行了模擬，理論計算出圓柱狀石蠟和圓柱狀銅整體達到熱平衡狀態所需的時間，並且和實驗中所測納米銅粒石蠟溫敏復合材料達到熱平衡狀態所需的加熱時間進行了對比分析。
  17. A bow type head on this probe for measurement of rollers, pipes, cylinders and most curved surface

    一種端子上帶有弓狀的探頭，專供測量滾軸、管道、圓柱體和極彎曲的表面。
  18. The ratma can calculate the electromagnetic scattering of multiple cylinders, and can be used in remote sensing. in chapter 2 simply derivation of the ratma is given by the addition theorem, and the general t matrix of single cylinder is deduced. the worked out examples show th e effectiveness of the ratma in the analysis of the scattering field of single cylinder or multiple cylinders

    由於遞推t矩陣法不僅可以計算多個柱體或不同形狀柱體的散射，而且可計算遙感上三維物體的散射，在第二章中，利用加法定理，簡要地推導了遞推t矩陣法，並用解析法推出了單個圓柱體在各種情況下的t矩陣（此t矩陣對導體和介質圓柱體的散射場計算都適用） ，最後計算了單個導體圓柱和兩個不同大小介質圓柱體的散射場。
  19. Object shapes are represented by primitive shapes ( box, cone, cylinder, sphere ), and complexes of polytopes ( line segments, convex polygons, convex polyhedra )

    對象形狀用基本形狀（方框，圓錐形，圓柱，球）和復雜的多面體（線段，凸多邊形，凸多面體）來表達。
  20. The vertical and lateral forces were loaded on the column shape implants. results the stress on implant - bone interface was about equally distributing compressive stress

    採用二維光彈應力分析法，分析圓柱形種植體在垂直向和側向加載條件下種植體?骨界面的應力狀況。
分享友人
分享到 Line

分享到臉書