圓柱體軸線 的英文怎麼說

中文拼音 [yuánzhùtǐzhóuxiàn]
圓柱體軸線 英文
axis of a cylinder
  • 體 : 體構詞成分。
  • 軸 : 軸Ⅰ名詞1. （圓柱形的零件） axle; shaft 2. （對稱部分的直線） axis 3. （圓柱形的纏繞器物） roller; spool Ⅱ量詞（用於纏在軸上的線以及裝裱帶軸子的字畫）
  • 線 : 名詞1 （用絲、棉、金屬等製成的細長的東西） thread; string; wire 2 [數學] （一個點任意移動所構成的...
  • 軸線 : 1 [機械工程] axis; axle; [地質學] axial trace; axial cord; axis shaft line; shaft line 2 [紡織] s...
  1. Four kinds of situations between the smallest outer - contained hexahedron of the same point series and axis of cylinder are presented, and the reliability of the above stated model and analysis is verified by living example

    給出了同一點列的最小外包容六面體與圓柱軸線間的4種情況，並用實例驗證了所述模型和分析的可靠性。
  2. First, the dynamic stability of braid composite cylindrical shells with the influences of some main factors is introduced. the general governing equations for the nonlinear dynamic stability is obtained. by the hamilton principle. the creep buckling analysis of braid composite cylindrical shells under axial compression and the dynamic stability under nonconservation force are discussed as emphases. in creep buckling question, by means of theoretical analysis, the instaneous critical load and durable critical load of viscoelastic braid composite cylindrical shell under axial compression are obtained and the numerical example is given

    首先介紹了編織復合材料圓柱殼在幾種主要因素影響下的動力穩定性問題，用hamilton原理建立非線性動力穩定性問題的一般性基本方程。然後重點討論了編織復合材料圓柱殼軸壓下的蠕變屈曲問題及非保守力作用下的屈曲問題。對蠕變屈曲問題，通過理論分析來得到了編織復合材料圓柱殼的瞬時彈性臨界載荷和持久臨界載荷，給出了具體的算例。
  3. Abstract : by cooperating the two - model method with parallelogram frame in this paper, the curve of two crossed cylinders with their axises in a state of vertical can be easily and accurately realized, and the mechanism withdrawn from the method can be applied directly to the hole gas - cutting on high pressure capsules

    文摘:採用雙靠模法與平行四邊形機構的組合，可簡易、準確地實現軸線垂直的兩圓柱體相貫線軌跡的復現，其原理可直接用於壓力容器上圓孔的氣割。
  4. By solving an inverse heat conduction problem, one method is developed for the estimation of the temperature of a hot wire embedded at the center of a cylinder based on infrared temperature - measuring

    摘要利用紅外測溫技術，結合導熱反問題求解，給出了一種根據加熱圓柱體外壁溫度紅外監測反推圓柱體中心軸線上熱導線溫度的方法。
  5. In this paper, the pressure field and static characteristic of bearings are simulated by fluent. the pressure contours of restrictors and shaft are acquired as well as the load capacity and static stiffness curves versus eccentricity ratio

    本文首次應用它對軸承的壓力場和靜態特性進行了模擬分析，得出了氣體流經小孔、多孔柱塞和全多孔質的壓力變化曲線以及軸上壓力沿軸向和圓周方向上的變化趨勢，並給出了軸承的承載能力和靜態剛度曲線。
  6. In the calculating example of model inversion, the proper sampling interval and ' trend - band ' method were selected and inversion errors of the linear density and axes depth of cylinder were close to 0. 25 % and 3. 8 %, respectively

    在模型反演算例中，選擇了適當的采樣間隔和「趨勢鑲邊」法，反演的圓柱體線密度和軸心深度誤差分別為0 . 25 %和3 . 8 % 。
  7. The conclusion can be drawn that the method can be applied to the determination of the temperature of a hot wire embedded at the center of a cylinder

    經數值計算驗證，本方法可對薄壁高溫的加熱圓柱體軸線上的熱導線的溫度給出高精度的定量檢測結果。
分享友人
分享到 Line

分享到臉書