塊形接觸 的英文怎麼說

中文拼音 [kuāixíngjiēchù]
塊形接觸 英文
bump contact
  • 塊 : 名詞（古時佩帶的玉器） penannular jade ring （worn as an ornament in ancient china）
  • 接 : Ⅰ動詞1 （靠近;接觸） come into contact with; come close to 2 （連接; 使連接） connect; join; put ...
  • 觸 : Ⅰ動詞1 （接觸） touch; contact 2 （碰; 撞） strike; hit 3 （觸動） touch 4 （感動） move sb ; sti...
  • 接觸 : 1. （交往） come into contact with; get in touch with 2. （沖突） engage 3. （挨上; 碰著） contact; touch
  1. The particles distributed hi the matrix of grey cast iron, but some contact each other. the composite layer extend gradually into the substrate. when volume fraction of wc is 36 wt % and 27 wt %, the matrix of the composite is high chromium cast iron, consist of white carbide bars and the austenite. wc particles distributed uniformly, retaining approximately quondam granular form in the composite layer which has an evident interface area with the substrate, with good bonding strength

    對不同碳化鎢體積分數的灰鐵和低鉻鑄鐵基復合材料的微觀組織結構分析表明：碳化鎢體積分數為52時，復合層內基體為灰口鑄鐵組織，顆粒直接分佈在灰鐵基體上，部分碳化鎢顆粒有相互接觸的現象，基材與復合層之間沒有明顯的過渡；碳化鎢體積分數為36 、 27時，復合層內基體為高鉻鑄鐵，由面塊狀的奧氏體和白條狀碳化物組成，碳化鎢顆粒表面固溶於基體組織中，粒形基本保持完整，分佈均勻，與基體構成冶金結合，基材與復合層之間存在一個明顯的平緩過渡區。
  2. The thesis developed the optimization design software of geometric parameter for the worm gear including strength check module, the drawing contact lines module, the change lines of tooth thickness of worm, and the parametric modelling software for the reducer which includes parametric modelling of parts and assembly. the cad prototype system is very convenient because of its accessible interfere, simple operation and written in chinese. by input design parameters ， the cad system can make optimization design and strength check for the worm gear ， draw contact lines of tooth flank of worm - gear and change line of tooth thickness of worm ， judge if the tooth flanks of worm undercut and if the sideward tooth of worm - gear hob come to a point ， make project design and structure design for the reducer and draw its 2d parts and assembly

    研究和開發了平面二次包絡環面蝸桿傳動的參數優化設計和校核軟體系統：包括幾何參數設計計算模塊，強度校核模塊，繪制齒面接觸線模塊，蝸桿齒厚變化曲線模塊和蝸桿根切判別模塊；開發了平面二次包絡環面蝸桿減速器外形與結構尺寸數據庫以及傳動效率數據庫，建立了平面二次包絡環面蝸桿傳動公差及極限偏差數據庫；開發了平面二次包絡環面蝸桿減速器參數化建模軟體：包括零部件的參數化建模模塊和裝配圖的參數化建模模塊，其中零部件的參數化建模包括蝸桿軸系的參數化建模、蝸輪軸系的參數化建模、箱體的參數化建模、端蓋的參數化建模、軸承的參數化建模和其它零部件的參數化建模軟體模塊。
  3. The 3d model of mold is analyzed in 3d fem by using ugh. base on the analyses result, some danger structure of the model have been found and some suggestions of the mold modification are given. since doing a lot of research about the 3d cadvcae technology, a 3dcad system of selecting mold for aluminum material have been developed and the method of analyzing the 3d model is provided in this paper

    然後，為了能真實地模擬實際生產過程，進行鋁與模具鋼在一定表面粗糙度、不同溫度條件、不同潤滑接觸狀態下的最大靜摩擦系數實驗，總結摩擦系數隨溫度變化的規律性和取值范圍；最後，應用ug 17 . 0三維有限元cae模塊進行模具三維力場分析，根據三維有限元的結果分析，對模具危險部分進行預變形的處理和優化，改善模具受力變形的狀況。
  4. After designing oil ditches on the surface of its arc - block, increase friction factor and make sure self - lock which solves above problem. do qualitative analysis to lower pair and one - way overrunning clutch and inner star - wheel - roller overrunning clutch by using self - made lever loader. the experiment shows : on the same condition, the deformation of new overrunning clutch ’ s surface contact with lower pair is smaller than the deformation of roller overrunning clutch ’ s line contact with higher pair and new overrunning clutch ’ s skid angle is smaller

    對低副單向超越離合器的部件進行了加工製造，在超越離合器弧塊表面創新設計加工排油溝，增大摩擦系數，保證實現自鎖，解決了很多離合器工作過程中容易出現無法自鎖的問題;對低副單向超越離合器和內星輪滾柱超越離合器用自製杠桿加載器做了定性分析，實驗表明:相同條件下，新型離合器低副面接觸比滾柱離合器高副線接觸變形小、溜滑角小。
  5. Detailed demonstrations and designs for each module ' s scheme are given, including diameter and length contacting module, mass contacting module, dishing depth contacting module, photoelectric microscope non - contacting module, verticality contacting module and data acquisition module. after design, strict accuracy analyses for each measuring module are given

    該文對各測量模塊的測量方案進行了詳細的論證和設計，包括直徑高度接觸式測量模塊、質量接觸式測量模塊、碟形深度接觸式測量模塊、倒角肩寬碟寬非接觸式測量模塊、垂直度接觸式測量模塊以及數據採集模塊的設計。
  6. It would lead to much more errors and complex scanning structure set. measuring wheel set flange by digital camera needed confirming rim inside plane by special object. it was difficult to measure running wheels because data transmission speed was slow

    數碼相機測量輪對踏面形狀的方法，需要用試塊接觸內側面進行定位，另外數碼相機的拍攝和傳輸速度一般均較慢，難以用於轉動中輪對踏面的測量。
  7. In this paper, the block element method is used to simulate the discontinuities. the structural planes in rock masses are simulated by the contacted elements between block elements while the rheological property of the structural planes are considered by the usage of a complex rheological model describing elastic - viscoelastic - viscoplasticity as the constitutive relation of contacted elements

    本文採用塊體單元法來模擬巖體變形的不連續性，以塊體單元之間的接觸縫面單元來模擬巖體中的結構面，在接觸縫面單元的本構關繫上引入西原模型來研究巖體的流變性質，並進行了工程應用。
  8. 2. click a portion of the split task bar, and drag it from right to left until it touches the nearest portion

    2 .單擊拆分任務條形圖的一個任務塊，然後將其從右向左拖動，直到接觸到距離最近的任務塊為止。
  9. Defer any tile or keystone extraction until we evaluate using these minimal - contact methods

    推遲任何整塊或楔形塊取出直到我們以這種最小接觸的方法評估完。
分享友人
分享到 Line

分享到臉書