塑性力矩 的英文怎麼說

中文拼音 [sùxìnglìjǔ]
塑性力矩 英文
plastic moment
  • 塑 : 動詞（塑造） model; mould
  • 性 : Ⅰ名詞1 （性格） nature; character; disposition 2 （性能; 性質） property; quality 3 （性別） sex ...
  • 力 : Ⅰ名1 （力量; 能力） power; strength; ability; capacity 2 [物理學] （改變物體運動狀態的作用） forc...
  • 矩 : 名詞1. （畫直角或正方形、矩形用的曲尺） carpenter's square; square2. （法度; 規則） rules; regulations 3. [物理學] moment
  1. Moreover, popularizing such system is expected. the following works have been fulfilled within this thesis : first of all, based on the general principle of virtual displacement of nonlinear continuum mechanics, the geometric and material stiffness matrices is presented, several examples show that both of them can give out accurate result

    本論文主要完成了以下工作：首先，根據連續介質力學理論構造出的交錯桁架結構空間單元的幾何剛度矩陣和彈塑性剛度矩陣，算例分析表明這些矩陣能準確地計算出結構的空間二階效應和空間單元彈塑性桿端力增量，計算結果具有良好的精度。
  2. Based upon virtual displacement method and the updated - lagrangian approach, stiffness matrices for two - dimensional elastic - plastic beam model in large displacement were proposed, in the derivation of which transverse stress was included because it was believed that part of the 2nd order effects of various stresses, which are in equilibrium with each other and with the external loads, will counteract each other and neglecting either part would possibly lead to incorrect results

    利用虛位移原理和更新的拉格朗日方法，導出了大位移彈塑性梁單元剛度矩陣的顯式表達式，在剛度矩陣推導中引入了截面內非線性剪應力和橫向應力的影響，剛度矩陣通過了剛體檢驗。之所以要引入橫向應力的影響，是因為本文認為，保持平衡所需的所有應力，它們各自的二階效應會相互抵消，因此忽略其中的任何一項都可能導致不正確的結果。
  3. From the feature of the force and deformation of the tpih, 5 different elements are used to mesh the different zones of the tube, which are structural beam 3d elastic 4, structural pipe plastic straight 20, structural pipe elastic elbow 18, structural shell elastic 4 node 63 and contact 3d pt - to - surf 49 ; the contact problem is assumed to be flexible - to - flexible ; the temperature field is assumed to be body load. a mechanical model corresponding to reality has been established for numerical simulation. based on the above, the 3 - d fem numerical simulation of tpih has been carried out by using the ansys program

    針對加熱彎管過程的受力和變形特點，採用三維梁單元、三維塑性直管單元、三維彈性曲管單元、三維殼單元與三維點對面接觸單元等5種不同的單元分別對管毛坯不同區域進行劃分，並對接觸單元採用柔體-柔體的處理方法，將溫度場作為體載荷處理，建立了符合實際的加熱彎管問題數值模擬力學模型：在此基礎上，應用商用軟體ansys對加熱彎管過程進行三維有限元模擬與研究，獲得了成形時推力、彎矩、支撐力大小及其變化趨勢。
  4. Point to above problems, under the financial support of the national natural science foundation ( exploration of high tech and new concept and new conceive ), the excellent young teachers program of ministry of education and national excellent doctoral dissertation special foundation, the static and dynamic real - time computation of elasticity - plastic mechanics, solving method of fuzzy finite element and other problems were studied in this paper. and some achievement was gained as following : ( 1 ) based on the positive definiteness of system stiffness matrix of finite element that was modified and the form of potential energy function of elastic body, the linear system of saturation mode ( lssm ) was introduced into the neural computation of finite element, by which the no - error solving of finite element neural net computation was realized in theory

    針對上述問題，在國家自然科學基金（高技術新概念新構思探索） 、教育部優秀青年教師資助計劃、高等學校全國100篇優秀博士學位論文作者專項基金等的資助下，本文對彈塑性力學問題的動靜態的實時計算、模糊有限元的求解方法等問題進行了系統和深入的研究，取得了以下成果： （ 1 ）根據有限元總剛矩陣經修正後具有正定性的特點以及彈性體勢能函數的具體形式，將飽和模式的線性系統（簡稱為lssm系統）引入到有限元的神經網路計算中，在理論上實現了有限元神經網路計算的無誤差求解。
  5. It ' s an ideal structural system and has multi - earthquake resistance ability because of a great deal of slabs removed in floors above the transfer - story amended the lateral stiffness of the stories near the transfer - story. based on the available references, the five - spring line element, the three - spring line element and the multiple vertical - line - element model are introduced to model special column, beam and shear - wall, the relevant stiffness matrixes are deduced and the restoring - force models are gaven to deep into the elasto - plastic seismic characteristics of the structure. acording to the results of shaking table test and elastic finite element analysis, a new making model melhod is presented in which uses the linear and the nonlinear element and the assumption that the floor is infinitely rigid in different areas

    為進一步研究這種復雜高層建築結構的彈塑性性能，本文在國內外現有研究的基礎上，提出利用五彈簧桿元、三彈簧桿元及多豎線單元模型分別模擬空間柱、梁和剪力墻，推導了相應的剛度矩陣並給出了恢復力模型；結合試驗研究和精細有限元分析的結論，提出線性和非線性單元相結合，剛性樓板假定和彈性樓板相結合的建模方法，較好地解決了空間結構彈塑性分析中佔用計算機資源較多的問題；接力大型有限元分析程序? ? ansys ，在上述建模思路的指導下建立了結構的空間非線性分析模型，進行了空間三維彈塑性時程分析。
  6. ( 3 ) by using an elastic - plastic material model, the nonlinear analysis is taken on the rectangular tube and simply supporte d plate, and the ultimate carrying load capacity pu is obtained. the results show that the buckling mode is in accordance with the assumption of elastic analysis, and so shows the ultimate mode

    （ 3 ）採用彈塑性模型，考慮幾何非線性理論，利用ansys軟體對矩形鋼管考慮板組相關屈曲影響和不考慮相關屈曲影響（將矩形管板件按四邊簡支板對待）兩種情況進行了屈曲後分析，分別得出其極限承載力p _ u ，並分析了矩形管的屈曲過程。
  7. On the basis, three elastic calculation coefficients of the two - way composite slab on three common boundary conditions are deduced and calculated by applying the classic elastic plane theory. in the thesis, the elastic design methods of pk prestressed composite two - way slab is explored and studied by the example. furthermore, it is also studied how to apply the yield - line design method to design the prestressed two - way composite floor slabs

    本文以此為依據，應用經典彎曲薄板理論，採用李維法推導和計算了這種雙向樓板三種常見邊界下的撓度和內彎矩彈性計算系數，並在此基礎上通過算例探討了pk預應力雙向疊合樓板的彈性設計方法，同時還對其塑性鉸線設計方法進行了研究。
  8. At last, with the program, 18 one - storey and one - span prestressed frames are simulated. some conclusions are reached with the taking into account the, secondary moment and types of load applying : ( 1 ) the in the beam affects the ductility of the section and rotary property of the plastic hinge. so total coefficient of the modulation of moment becomes less with the becoming bigger

    最後，本文利用編制的非線性程序，模擬了18榀單層單跨預應力框架，重點研究截面相對受壓區高度、次彎矩、加載方式對塑性內力重分佈和彎矩調幅的影響，從中得出了以下主要的結論和規律： （ 1 ）框架梁相對受壓區高度在很大程度上反映了截面的延性，體現了塑性鉸的轉動能力，框架的總彎矩調幅系數隨著相對受壓區高度的增大而減小。
  9. Based on the experimental study of two presstressed frames, it analyses the question of redistribution of internal force and analyses influence of moment modulation of prestressed frames. therefore, it draws some conclusion as follow : 1 ) post - tensioned prestressed frames can be practiced on moment modulation. but how to operate decides on practical situation in design

    本文通過對兩榀近於足尺的后張有粘結預應力框架在跨間豎向荷載作用下的試驗研究，探討了預應力框架內力重分佈問題，從塑性內力重分佈入手分析了次彎矩對框架彎矩調幅的影響以及影響內力重分佈的其他主要因素，得到一些概念性的認識和結論： （ 1 ）對后張有粘結預應力框架可進行適當調幅。
  10. Then, a step - by - step increase of vertical curvature is applied to the hull girder assuming that the plane cross section remains plane. at each incremental step, the stress of the cross section is evaluated using the average stress - strain curves of the elements as well as the incremental bending moment due to the curvature increment. performing sample calculations on existing girder models tests under pure bending, the rationality of the proposed method was examined

    假設船體橫向框架材足夠強，因而板架的整體破壞不會發生；基於梁?柱理論、理想彈塑性假設、平面假設，建立了拉伸和壓縮加筋板單元的平均應力?應變關系曲線，應用船體結構總縱極限強度的簡化逐步破壞分析方法計算船體總縱極限彎矩，並據此開發了計算程序sus 。
  11. The effect of different sizes of sections, modes and values of residual stresses are studied. through the analysis, the conclusion is arrived at that the universal slenderness ratio should be used to better correlate the stability of box section beams with the member length instead of the out - of - plane slenderness, and the stability coefficient is taken to be 1. 0 for practical used box girder. then, the elastic critical loads of box section beam - columns are obtained based on the gjelsvik theory, and the relationship between axis force p and moment m is given

    最後，運用ansys通用有限元程序的beam189單元，引入初彎曲和殘余應力的影響，用考慮幾何和材料雙重非線性的有限元求解格式求得箱形柱在不同軸力和彎矩比例作用下的彈塑性極限承載力，通過對十幾個不同截面尺寸構件在不同長細比下的承載力計算，發現在軸力p遠大於彎矩m時，構件將是平面外失穩控制，而當軸力p遠小於彎矩m時，構件則以平面內失穩為主。
  12. But this time, the authors considered more factors that can influence the precise, which include plastic resistant moment of special - shaped columns, bending stiffness of beams and cracking of walls. then, the equivalent width of diagonal strut is worked out. based on above results, the bar system model is used to calculating the internal force of the structure and the results were match the testing data basically

    給出結構的簡化計算方法，本文利用砌塊墻體的斜壓桿等效原理，並考慮了異形柱的塑性抵抗矩、 0梁的抗彎能力以及馬牙搓連接等多種因素，解出了斜壓桿的等效寬度，在此基礎上按桿系模型對結構進行了簡化靜力驗算，結果與試驗基本相符。
  13. 5 ) the secondary moment postpones coming of plastic hinge on frames. in other words, it reduces requisition of rotation ability of section. therefore, it maybe improve modulation ability of frame

    （ 5 ）初始次彎矩的存在，推遲了梁端塑性鉸的出現，也就是說降低了彎矩重分佈對梁端轉動能力的要求，從而有可能提高總調幅能力。
  14. For example still the arguments exist about the cracking controlling, the behavior of secondary moment and the re - distribution of internal forces, especially for the moment, of the prestressed concrete continues beam or frame

    例如在對預應力混凝土連續梁和框架的裂縫控制、次彎矩以及結構的塑性內力重分佈尤其是彎矩重分佈這些問題上還存在著廣泛的爭論。
  15. New model for plastic design of continuous prestressed concrete beams - calculation of plastic moment in continuous prestressed concrete beams

    預應力混凝土連續梁結構塑性彎矩計算方法
  16. The contents include as follows : the influencing factors of the displacement ductility factor of the unbonded partially prestressed concrete frame structures, such as stirrup reinforcement characteristic value, nominal shear span ratio, axial compression ratio, the appearing order of plastic hinges and partial prestressing ralio ( ppr ) are discussed. the formula of displacement ductility factor of the unbonded partially prestressed concrete frame structures is suggested by regression analysis. with regard to the aseismic design and the request of ductility and energy dissipation, the restriction of the flat - beam / column sectional size and aseismic reinforced design are discussed

    本文主要包括以下內容：討論了配箍特徵值、名義剪跨比、軸壓比、塑性鉸出現順序、預應力度等因素對無粘結部分預應力混凝土框架位移延性系數的影響，回歸了考慮影響因素的位移延性系數計算公式；對無粘結部分預應力混凝土扁梁框架結構，闡述了抗震設計對扁梁、柱截面尺寸的要求與限制；對滿足延性和耗能要求的無粘結部分預應力混凝土扁梁控制截面抗震配筋進行了探討；通過對無粘結部分預應力混凝土扁梁梁端的受力分析，改進了以往扁梁梁端扭矩設計值計算公式。
  17. Then a semi - rigid joint behavior can be modeled as a finite stiffness rotation spring. basing on rotation and displacement equation, we obtain the element stiffness matrixes with semi - rigid connections where the effects of material nonlinear, hysteresis behavior and shear forces in the connection deformations have been considered in and at the same time we modify the fixed - end forces. finally, a program for calculating the elastic - plastic earthquake seismic of semi - rigid connected steel frame structure by step and step integration of wilson -

    本文在介紹和分析半剛性連接彎矩與轉角連接關系模型的基礎上，用帶有轉動剛度的彈簧表徵半剛性連接，推導出半剛性連接的剛度矩陣，並對桿件固端力進行修正，同時在考慮剪切變形、材料彈塑性、及構件的動力滯回性能的基礎上，編制了結構彈塑性地震動力時程分析有限元計算程序。
  18. Moreover, six externally prestressed beams which were experimented overseas were analyzed with this method developed, by comparing the calculation result and the experiment data, it is found that the calculating method has a satisfactory precision and is worth being promoted

    利用這一概念，建立了直接通過塑性鉸區長度和曲率半徑求體外預應力筋應力和梁極限彎矩的簡化公式，用簡化公式對國外有關6片體外預應力梁進行了計算，並與試驗結果進行對比，證明本研究中的簡化公式具有較好的精度，值得推廣。
  19. The load distributed by central piles under vertical load are higher than by others of the pile group ; 2. under higher vertical load, the foundation soil shows an obvious characteristic of plastic strengthening ; 3. the bearing capacity of pile group under vertical load is larger than the whole sum of bearing capacity of single piles in pile group ; 4. the position of the maximum or zero value of bending moment inpiles, the line shape of bending moment diagram and the value of bending moment of the same cross section of a pile under same load is different according to the lateral loading and the longitudinal loading ; 5

    在較大的豎向荷載作用下，土體出現明顯的塑性強化特徵； 3在豎向荷載作用下，群樁的承載力大於各基樁承載力之和； 4沿線路水平縱、橫向加載時，最大彎矩和零彎矩的位置、彎矩變化曲線的形狀以及在相同荷載作用下各樁同一截面的彎矩值都有一定差異； 5
  20. In this article the development of the cracks and the moment redistribution are discussed based on the two frames which are loaded vertically and horizontally at the same time

    本文針對兩榀同時施加有水平荷載和豎向荷載的預應力框架，對其加載過程中的裂縫發展、結構的塑性彎矩重分佈進行了探討和研究。
分享友人
分享到 Line

分享到臉書