塑性動力響應 的英文怎麼說
中文拼音 [sùxìngdònglìxiǎngyīng]
塑性動力響應
英文
dynamic plastic response-
The papers whose research object is the 7 - floor frame - structure with isolator - seismic layer, in which the isolator - seismic layer adopt some standard interlayer rubber isolator. by establish a 3 - dimension finite - element modal and use the a nalysis soft - ansys, we can make dynamic analysis on the structure. by analyses we can get some response characteristics of the structure sparked by the normal and rarely earthquake of 8 - degree fortify intensity, by the double - horizons seismic and by the vertical seismic
本論文設計了一7層的具有隔震層的框架結構並以此為研究對象，其中隔震層採用標準件的夾層橡膠隔震墊，通過建立三維有限元分析模型，運用大型有限元分析軟體? ansys對結構進行動力響應彈塑性時程分析，得出了結構在8度設防烈度下的常遇水平地震和罕遇水平地震激勵下的響應特性、在雙向水平地震波激勵下結構的響應特性和在豎向地震波激勵下結構的響應特性。The first stage is primary slip then followed by secondary slip ; the last stage is due to dislocation passing the slips. the cyclic stress strain ( css ) curve exhibits a stronger hardening occurred in cyclic plastic deformation than that in tensile test
建立了拉伸和應變疲勞的有限元模型，使用基於晶體滑移模型的數值方法，對晶體內部滑移系的啟動以及滑移繫上的分解切應變、切應力這些無法試驗觀測的變量進行計算，分析它們對晶體塑性變形的不同影響。Relating closely to the main problem of the high sidewall and wide span underground cavities excavation stability of xiluodu hydroelectric project, the evolution characters of geo - stress field in deep - cutting gorge and the whole features of the stress field, strain field and plastic failure zone around the underground chambers after excavation are studied systematically in the dissertation, based on a great deal of data gathered in field investigation and taking the flac3d v2. 0 software as basic computation tools. meanwhile, in the course of research, the new methods of dynamic numerical simulation are summarized and applied. furthermore, the effects of rock mass qualities, initial geo - stress field and excavation procedure on surrounding rock mass stability are discussed
本文緊密結合溪洛渡水電工程大跨度、高邊墻復雜地下廠房洞室群，施工開挖過程中和開挖后圍巖穩定性研究這一重大課題，在詳盡的野外地質調查工作和對大量基礎地質資料的整理與分析基礎上，以目前國際工程地質界公認的最新通用軟體flac ~ （ 3d ） 2 . 0版作為基本計算工具，從整個壩區地應力場的研究開始，通過動態數值模擬分析這一新的模擬思路，系統地研究了深切峽谷區地應力場多階段的特徵和演變規律，進而對左、右岸地下廠房洞室群開挖全過程中圍巖應力場、變形場和塑性破壞區的變化特徵，進行了全過程動態數值模擬研究，並詳細討論了圍巖質量、初始地應力場、施工開挖順序對大型地下洞室群圍巖穩定性的影響。Compared the results of fea and the data of experiment, we can analyse that the distributing of the seismic stress of polymer - geogrid reinforced material is similar to that of the static stress, but the stress values of them is different ; the seismic similar friction coefficient between the earth and reinforced material fall with the increasing of earthquake acceleration, model acceleration respond along the height of the model, etc. thirdly, according to the comparison and analysis of the model seismic fea results and model experiment data, we can find the polymer - geogrid reinforced earth seismic fea is reasonable, which is composed by earth element, contact element and reinforced material element
通過對比有限元計算結果和試驗數據，分析得出塑料土工格柵筋材的最大動拉應力的分佈與靜拉應力的分佈沿筋材的埋深大致相同，只是應力的值大小不同；地震作用下土筋間的動似摩擦系數是隨地震加速度的增加而減小；模型沿墻高方向的加速度響應等。接著，根據模型動力有限元時程分析結果和模型試驗數據的比較分析，得出由土體單元、接觸單元和筋材單元組合的塑料土工格柵加筋土非線性動力有限元分析模式的合理性。During the temperature fields, the results indicate that the processing parameters such as the extrusion velocity, casting temperature, perform preheating temperature, die preheating temperature and so on are important for the temperature fields besides the dwell time. they are must be in concordance each other to the deforming zone is in the quasi - solid state, and the stable semi - solid extrusion is implemented. during the deforming fields, the hyperbolic sine thermo - rigid - viscoplastic fem model is selected according to the forming feature of the process, and the variations of the stress - strain fields are studied
在溫度場的模擬中，模擬結果表明，保壓時間是影響製件成形質量的關鍵因素之一，擠壓速度、液態金屬澆注溫度、預制體預熱溫度和模具預熱溫度等工藝參數對溫度場的影響也很大，需進行參數之間的協調，只有當變形區內部始終維持準固態時，才能實現穩定的液-固擠壓成形過程；在變形場的模擬中，根據液態浸滲擠壓的成形特徵，選用了雙曲正弦剛-粘塑性有限元計算模型，研究了變形過程中應力應變場的變化規律，研究了模角對變形和金屬流動的影響及變形力的變化過程和其影響因素。Paper study the demolish process of high buildings with the nonlinear dynamic program of three - dimension. with the increase of earthquake motion, the f100r that takes the greatest distortion is changed
在開發運用三維非線性程序canny的基礎上，對高層結構進行彈塑性動力響應分析，研究了高層建築的破壞過程。Elastic - plastic dynamical response mechanism of a cantilever beam subjected to oblique impact at its tip
端部受斜撞擊作用懸臂梁的彈塑性動力響應模式Non linear static & dynamic finite element procedure is adopted for the true emulation of the four typical geologic profiles of the dam, and imitates to compute the each stage deformation and stress distribution from the dam fill to full water run and during the 7 degree seismic intensity, the article also imitates to compute the response to earthquake force, the excess vibration pore water pressure distribution and permanent deformation, predicting the occurrence possibility of the crac ^ plastic zone and earthquake liquefaction
採用非線性靜、動力有限元分析程序對圍壩的4個典型剖面進行了靜、動力模擬模擬，模擬計算了壩體自填築至蓄水運行和發生7地震各階段壩體及壩基的變形以及應力分佈，地震應力響應和地震引起的超靜振動孔隙水壓力分佈以及永久變形。判斷了壩體和壩基中出現裂縫、塑性區以及地震液化的可能性。At last, with the program, 18 one - storey and one - span prestressed frames are simulated. some conclusions are reached with the taking into account the, secondary moment and types of load applying : ( 1 ) the in the beam affects the ductility of the section and rotary property of the plastic hinge. so total coefficient of the modulation of moment becomes less with the becoming bigger
最後，本文利用編制的非線性程序，模擬了18榀單層單跨預應力框架，重點研究截面相對受壓區高度、次彎矩、加載方式對塑性內力重分佈和彎矩調幅的影響，從中得出了以下主要的結論和規律： （ 1 ）框架梁相對受壓區高度在很大程度上反映了截面的延性，體現了塑性鉸的轉動能力，框架的總彎矩調幅系數隨著相對受壓區高度的增大而減小。In fact, the constitutive models employed in both methods could not re - produce the dynamic behaviour of soil to non - proportional cyclic loading, such as waves loading. to simulate dynamic responses of elastic, visco - elastic and elasto - plastic sea beds, linear and / or non - linear numerical models based on generalized biot ' s theory are developed together with stable and effective algorithm. the difficulty in numerical computation made the generalized biot ' s theory be difficult to be put into practice in the field of geotechnical engineering
上述兩種方法採用的土體本構模型都不能再現砂土在暴風浪等非比例加載條件下的動力特性，本文基於廣義biot理論提出了波浪作用下海床線性或非線性動力響應的耦合計算模型與穩定、高效數值演算法，分別針對土的彈性、粘彈性與彈塑性本構關系，對海床的動力響應進行了有限元數值模擬與分析。Magneto - elastic - plastic dynamic responses and instability of beam - plate excited by magnetic pulse
磁脈沖作用下鐵磁梁式板的磁彈塑性動力響應與失穩In the area of elasto - plastic dynamic analysis of frame with friction energy dissipation, the design - oriented nonlinear seismic response time history analysis method for frame with friction energy dissipation has been set up. and the corresponding program idaff is developed using visual c + + language ; the analytic solution of a single - damped - story braced frame with friction energy dissipation under the sine wave excitation has been give ; besides these, a vibration reduction analysis of multi - story frame with friction energy dissipation has been given in the paper and some useful conclusions have been drawn
在摩擦耗能框架結構彈塑性動力分析方面，本文建立了面向設計的摩擦耗能框架結構非線性地震反應時程分析方法，並利用vc + +編制了相應的程序idaff ；給出了帶有摩擦耗能器的有阻尼單層框架在正弦波激勵下反應的解析解；同時本文從多自山度的角度出發對摩擦耗能框架的影響因素進行分析，得出相關的結論。First, one type of sma - based passive energy dissipation device was developed to utilize pseudo - elastic property. then, according to the characteristic of response of the passive energy dissipation systems, adapting the bilinear restored force model, the mof shear type elastic - plastic time history analysis program is compiled. the vibration - suppressed is verified and vibration control mechanism of sma dampers is studied by time - history analysis
首先利用sma的超彈性性能，設計了一種新型的耗能減震裝置；其次，結合耗能減震結構的動力反應特點，採用雙線性模型，編制了耗能減震結構串聯多質點體系彈塑性時程分析程序，通過對有控結構和無控結構的地震響應分析比較，檢驗了sma耗能器的被動控制效果，探討了其控制機理。The direct solution for u ~ u and u ~ p form, the stagger solution for u ~ p form are compared in the convergency, stability and efficiency, from which it is concluded that the first solution used not widely before is characterized with weakly ill - conditioned stiffness and comparatively high efficiency. the finite element methods based on these three solving procedures are numerically implemented. the seabed soil under wave pressure with small amplitude can be viewed as elastic material
詳細比較廣義biot理論u u形式直接解法、 u p形式直接解法與交叉迭代法求解彈性、彈塑性問題的收斂性、穩定性與計算效率，認為以往較少應用的u u形式直接解法剛度陣病態性弱，求解效率高，更適合土工問題的數值模擬，小風浪作用下海床的動力響應特性可視為彈性的。The article has applied the weighted residual method and laplace changing to analyze the plastic dynamic response of a simple circular plate, the influence of elastic foundation on it and drives its residual deflection and the terminal time
摘要應用加權殘值法和拉普拉斯變換，分析彈性基礎上簡支圓板的塑性動力響應問題，彈性基礎對薄板塑性動力響應的影響，並且給出板的殘余撓度和終止運動時間。Finally, the analysis of elastic - plastic time - history on r. c. frame structure with special - shaped column is conducted by plane structure elastic - plastic time - history analysis the procedure ndas2d ( nonlinear dynamic analysis of structures in two dimensions ) programmed in structural system composed of bar, 24 earthquake waves is adopted according to site classification
第四，採用桿系模型編制的平面結構彈塑性地震響應分析程序ndas2d ，對鋼筋混凝土異形柱框架結構進行了彈塑性動力時程分析。Dynamic plastic response
塑性動力響應Applying weighted residual methord to analyze the plastic dynamic response of a simple circular plate on elastic foundation
用加權殘值法分析彈性基礎上簡支圓板的塑性動力響應The plastic kinetic response of rivet is analyzed by sequentially coupling which take the first step ' s result as initial conditions
將模擬出的電流和電磁場結果作為初始條件，採用間接順序耦合方法分析鉚釘結構單元的塑性動力響應。The dynamic plastic response for a pinned rigid plastic beam subjected to an arbitrary impulsive distributed load was investigated. the effect of strain hardening and strain rate sensitivity was ignored. the yielding curve was assumed to be rectangular
採用剛塑性假定，忽略應變強化效應和應變率的效應並考慮由於有限變形而導致的軸力的影響，研究任意時間歷程沖擊載荷作用下簡支梁的塑性動力響應問題。分享友人