塑性極限彎矩 的英文怎麼說

中文拼音 [sùxìngjíxiànwānjǔ]
塑性極限彎矩 英文
plastic limit bending moment
  • 塑 : 動詞（塑造） model; mould
  • 性 : Ⅰ名詞1 （性格） nature; character; disposition 2 （性能; 性質） property; quality 3 （性別） sex ...
  • 極 : i 名詞1 （頂點; 盡頭） the utmost point; extreme 2 （地球的南北兩端; 磁體的兩端; 電源或電器上電流...
  • 限 : Ⅰ名詞（指定的范圍; 限度） limit; bounds Ⅱ動詞（指定范圍, 不許超過） set a limit; limit; restrict
  • 彎 : Ⅰ形容詞（彎曲） curved; bent; crooked; flexuous; tortuous Ⅱ動詞1 （使彎曲） curved; bend; flex 2 ...
  • 矩 : 名詞1. （畫直角或正方形、矩形用的曲尺） carpenter's square; square2. （法度; 規則） rules; regulations 3. [物理學] moment
  • 極限 : 1 （最高的限度） the limit; the maximum; the ultimate limit; limitation; extremity; tipping point...
  1. Plastic theory suggests, the composite beam for the floorslab is suited lower flange, it s plastic limit moment cuts down by 52. 4 % than the composite beam for the floorslab is suited on the top flange. it s plastic limit moment lifts 8. 8 % than the steel beam, which is on the same condition

    塑性理論分析的結果表明，樓板位於鋼梁下翼緣形式的組合梁和樓板位於鋼樑上翼緣形式的組合梁截面相比較，其塑性極限彎矩降低52 . 4 ，和同等條件下純鋼梁截面相比較，樓板位於鋼梁下翼緣的組合梁塑性極限彎矩提高8 . 8 。
  2. Then, a step - by - step increase of vertical curvature is applied to the hull girder assuming that the plane cross section remains plane. at each incremental step, the stress of the cross section is evaluated using the average stress - strain curves of the elements as well as the incremental bending moment due to the curvature increment. performing sample calculations on existing girder models tests under pure bending, the rationality of the proposed method was examined

    假設船體橫向框架材足夠強，因而板架的整體破壞不會發生；基於梁?柱理論、理想彈塑性假設、平面假設，建立了拉伸和壓縮加筋板單元的平均應力?應變關系曲線，應用船體結構總縱極限強度的簡化逐步破壞分析方法計算船體總縱極限彎矩，並據此開發了計算程序sus 。
  3. The effect of different sizes of sections, modes and values of residual stresses are studied. through the analysis, the conclusion is arrived at that the universal slenderness ratio should be used to better correlate the stability of box section beams with the member length instead of the out - of - plane slenderness, and the stability coefficient is taken to be 1. 0 for practical used box girder. then, the elastic critical loads of box section beam - columns are obtained based on the gjelsvik theory, and the relationship between axis force p and moment m is given

    最後，運用ansys通用有限元程序的beam189單元，引入初彎曲和殘余應力的影響，用考慮幾何和材料雙重非線性的有限元求解格式求得箱形柱在不同軸力和彎矩比例作用下的彈塑性極限承載力，通過對十幾個不同截面尺寸構件在不同長細比下的承載力計算，發現在軸力p遠大於彎矩m時，構件將是平面外失穩控制，而當軸力p遠小於彎矩m時，構件則以平面內失穩為主。
  4. Moreover, six externally prestressed beams which were experimented overseas were analyzed with this method developed, by comparing the calculation result and the experiment data, it is found that the calculating method has a satisfactory precision and is worth being promoted

    利用這一概念，建立了直接通過塑性鉸區長度和曲率半徑求體外預應力筋應力和梁極限彎矩的簡化公式，用簡化公式對國外有關6片體外預應力梁進行了計算，並與試驗結果進行對比，證明本研究中的簡化公式具有較好的精度，值得推廣。
  5. Using the improved model, an ultimate bending moment formula is presented

    在梁的極限分析中採用新的剛塑性模型，推導出極限彎矩公式。
  6. Limit moment of nozzle in cylindrical vessels

    圓柱形容器接管塑性極限彎矩
  7. Plastic limit bending moment

    塑性極限彎矩
分享友人
分享到 Line

分享到臉書