塑性疲勞 的英文怎麼說

中文拼音 [sùxìngpíláo]
塑性疲勞 英文
plastic fatigue
  • 塑 : 動詞（塑造） model; mould
  • 性 : Ⅰ名詞1 （性格） nature; character; disposition 2 （性能; 性質） property; quality 3 （性別） sex ...
  • 疲 : 形容詞（疲乏; 勞累） tired; weary; exhausted
  • 勞 : Ⅰ動詞1 （勞動） work; labour 2 （煩勞） put sb to the trouble of; trouble sb with sth : 勞您費心...
  • 疲勞 : 1. （疲乏勞累） tired; fatigued; weary; become fagged 2. （機能或反應能力減弱） fatigue; strain 3. [物理學] fatigue
  1. Rubber, vulcanized and thermoplastic - determination of temperature rise and resistance to fatigue in flexometer testing

    硫化和熱塑橡膠.撓度計試驗中溫度上升和抗疲勞性的測定
  2. The anti - wearing property of chme steel is 15 percent to 35percent higher than zgmnl3, which is a widely used anti - wearing steel. the reason of the excellent mechanical properties and anti - wearing property of chme steel is that the heat treatment sturcture of chme steel is composed of tempered martensite, bainite, temper troostite, remaining austenite and carbonide

    磨面分析表明， chme鋼基體高強度，高硬度、良好的強韌性配合和碳化物硬質點的彌散分佈，磨痕細短淺小，擠塑變形區細小均勻，抵抗沖擊滑動累積塑性疲勞能力強，是其耐磨性比zgmn13高的原因。
  3. 3. studying on prediction methods of the initiation life of aero - gear using shakedown analysis methods in order to directly consider in a quantitative way the details of stress - inelastic strain responses, residual stress and residual strain computations, fatigue crack initiation life was evaluated in aero - gear by using th

    利用chaboche的材料模型，研究了航空齒輪韌性材料在彈、塑性安定下的輪齒接觸疲勞裂紋萌生準則，該研究結果與相關的齒輪實驗結果比較分析表明：塑性安定下的疲勞裂紋萌生預測方法預測航空齒輪的萌生壽命是較安全的。
  4. The first stage is primary slip then followed by secondary slip ; the last stage is due to dislocation passing the slips. the cyclic stress strain ( css ) curve exhibits a stronger hardening occurred in cyclic plastic deformation than that in tensile test

    建立了拉伸和應變疲勞的有限元模型，使用基於晶體滑移模型的數值方法，對晶體內部滑移系的啟動以及滑移繫上的分解切應變、切應力這些無法試驗觀測的變量進行計算，分析它們對晶體塑性變形的不同影響。
  5. Fiber reinforced plastic rebar ( frp ) is a new composite, which is composed of fiber acting as reinforced material, synthetic resin acting as matrix, and some adequate auxiliaries, and is formed through a pultrusion process and necessary surface process. it has a high strength to weight ratio, excellent non - corrosive characteristic, fatigue - resistant characteristic, strong designability and magnetic neutrality, so it can be used in the applications with special performance requirements or where reinforcing bars are subjected to severe chemical attack

    纖維增強塑料筋是以纖維為增強材料，以合成樹脂為基體材料，並摻入適量輔助劑，經拉擠成型技術和必要的表面處理所形成的一種新型復合材料，具有比強度高、耐腐蝕性能好、可設計性強、抗疲勞性能好、耐電磁等獨特優點。
  6. Flame tube in aircraft engine undergoes high temperature and high speed airflow washing. a hypothesis was suggested, which takes the transient heat transferring as the main reason to the cracking and damage on flame tube. finite element method was adopted to simulate the thermal fatigue and the hypothesis was reproduced

    發動機火焰筒的熱疲勞損傷是導致火焰筒失效的主要原因，本文提出了一種火焰筒熱疲勞損傷假設，認為火焰筒熱疲勞損傷不是由於發動機的運行和停車時冷熱溫度循環造成的，而是發動機啟動時瞬態溫度傳導過程中材料循環塑性變形的結果，利用該假設結合有限元計算模擬了火焰筒產生疲勞損傷的原因。
  7. Thermoplastics valves - fatigue strength - test method

    熱塑性塑料閥門.疲勞強度.試驗方法
  8. Fatigue property and superplastic deformation of bulk amorphous alloys

    塊體非晶態合金的疲勞性能與超塑性變形
  9. Topics include : elasticity, viscoelasticity, plasticity, creep, fracture, and fatigue

    主題包含：彈性、黏彈性、塑性、潛變、破斷及疲勞。
  10. In this dissertation, the effect of texture, heat - treatment, and hydrogen on the lcf behavior of zircaloy - 4 and the cyclic deformation behavior for zircaloy - 4, n18 alloy and n36 alloy have been investigated systematically using fully - reversed tension - compression loading under strain control ( r = min / max = - 1 ), while the evolvement of the friction and back stresses versus the number of repeated working cycles and the plastic strain amplitude has been studied, and the thorough discussion combined with the analysis result of fatigue sub - structure, friction and back stresses, and fatigue fracture has been given to the mechanism underlying the lcf behavior of alloys

    本文採用對稱拉壓循環變形方法（ r _ = _ （ min ） _ （ max ） = - 1 ） ，系統研究了織構、熱處理狀態、氫對zr - 4合金低周疲勞性能的影響， zr - 4合金、 n18合金和n36合金的循環變形行為，並研究了摩擦應力、背應力隨循環周次、塑性應變幅的變化規律。結合疲勞亞結構和疲勞斷口的分析結果，深入探討了影響合金低周疲勞行為的作用機制。
  11. The application of elastoplastic stochastic finite element method in low cycle fatigue analysis

    彈塑性隨機有限元在低周疲勞分析中的應用
  12. In this article, a new theoretical model on diametral growth ( or ballooning ) of coiled tubing ( ct ) under the action of an internal pressure is derived based on fatigue cyclic softening and elasticity and deformation plasticity theories

    根據疲勞循環屈服強度衰減模型和彈塑性變形理論，推導了連續油管在內壓作用下的直徑增長（鼓脹）的理論模型。
  13. Abstract : in this article, a new theoretical model on diametral growth ( or ballooning ) of coiled tubing ( ct ) under the action of an internal pressure is derived based on fatigue cyclic softening and elasticity and deformation plasticity theories

    文摘:根據疲勞循環屈服強度衰減模型和彈塑性變形理論，推導了連續油管在內壓作用下的直徑增長（鼓脹）的理論模型。
  14. Recommendations for the presentation of plastics design data - mechanical properties - static fatigue failure

    塑料設計數據表示方法推薦標準.第1部分:機械特性.第3 . 1節:靜態疲勞損壞
  15. Rubber, vulcanized or thermoplastics - determination of tension fatigue - constant strain method

    硫化橡膠或熱塑性塑料.張力疲勞測定.恆定應變法
  16. Multiaxial low cycle fatigue life prediction model based on plastic energy

    基於塑性應變能的多軸低周疲勞壽命預測模型
  17. Under varied loads such as cyclic and / or transient loading, soil structures or foundation will induce permanent and / or fluctuating plastic deformations. such plastic deformations are cumulative and / or alternating in nature with increase of time of loading during a sequence of cyclic loading. if the resulting accumulated deformations is limited within a given bound or the alternating deformations will be adapted to a given plastic state after a certain cycle numbers or a certain period of loading, the soils will be in shakedown state

    在復雜變值荷載作用下，結構有可能出現兩種狀態：一種是在若干次載荷循環之後，塑性變形趨于穩定，在此後繼的載荷循環中結構表現為純彈性響應，這種狀態稱為安定狀態（ shakedown ） ；另一種則是塑性流動一直持續地發展或不斷反復，直至結構破壞，結構的破壞有兩種型式：一種是由塑性應變的累積引起的增量塑性破壞；一種是塑性變形多次反復引起的疲勞破壞，也稱為交變塑性破壞。
  18. Lefm plastics - determination of tension - tension fatigue crack propagation - linear elastic fracture mechanics approach

    塑料.測定拉伸-拉伸疲勞斷裂延伸性.線性彈力斷裂機械
  19. General rules for testing fatigue of rigid plastics

    檢測硬質塑料疲勞性的一般規則
  20. Test method for flexural fatigue of plastics by constant - amplitude - of - force

    採用等幅強振動方法測定塑料撓性疲勞強度的方法
分享友人
分享到 Line

分享到臉書