塑變值 的英文怎麼說

Fist of all, on the basis of the research of agone boffins, this author investigates the interaction mechanism of bolts and rock, and introduces the elastic ? lastic analytical resolution which is consist of the liner structure, the equivalent reinforced wall rock and the original wall rock in the simple loading from the equivalent well - proportioned view ; this solution is very important meaning for the engineering design. on the basis of coulomb friction model, the author introduces the finite element equation of the contact problem in order to provide the academic foundation for the application of msc. marc. finally, combining the engineering practice of the non - linear analysis of shield tunnel through yellow river of the south - north water transfer and using the model of friction, the author researched the evolution law of stress and displacement field in the structure of grouted rock bolts, and analyzed the effect to the stress and deformation of surrounding rock mass due to anchor supports

首先，在前人研究成果的基礎上，對錨桿與圍巖的相互作用機理進行研究，利用全長錨固錨桿的中性點理論，從等效均化的角度來考慮錨桿對圍巖的加固作用，並推導了在簡單荷載作用下，含有襯砌、等效加固后的圍巖、原始圍巖三者的彈塑性解析解，對工程設計有著重要的參考意義；在數值模擬方面，以考慮錨固圍巖滿足規則化庫侖摩擦模型為基礎，利用虛功原理推導了接觸問題的有限元方程的計算格式，為開發運用大型商用有限元軟體msc . marc提供了理論根據，也形成了本文的理論基礎：最後，論文以南水北調東線穿黃隧洞穩定性分析項目為工程實例，利用本文所述的接觸問題的摩擦模型理論，對錨桿支護結構的應力場、位移場的變化規律進行了研究，分析了加錨支護對隧洞圍巖應力、變形的影響。

In view of bearing capacity of the elastoplastic theory analysis, the author made a comparison between the achieved bearing capacity limit load pi / 4 of round base ( space problem ) and the limit load pi / 4 of bar groundwork foundation design ( plane problem ) from soil mechanics at home and abroad as well as foundation criterion, and explained why the value of formula in present design criterion from soil mechanics is inclined to be conservative. in the light of the author ' s many years experience of vibration test on the spot and the research work of relevant projects, the author worked over the dynamic pile testing of the bearing capacity of foundation and batholith, and gathered the parameter of dynamic analysis and testing. the author also talked over the difficult point of pile foundation design criteria in present batholith engineering world, i. e. the confirmation of batholith bearing capacity of pile end, from the following aspects : a ) confirmation of single axis counter - pressure strength of rock in house ; b ) f. e. m calculation of elastoplastic model ; c ) calculation of soil mechanics ; d ) deep well load test

然後，對巖土工程領域至今尚未解決，甚至不為人注意的考慮地基變形的地基承載力問題進行了實用化的探討，提出了考慮地基變形的地基承載力上程計算方法；對基於彈塑性理論分析的地基承載力國內尚未見報道的空間問題得到了圓形基礎（空間問題）的承載力界限荷載p _ （ 1 / 4 ） ，並與國內外土力學專著及地基基礎設計規范中的條形基礎（平面問題）的界限荷載p _ （ 1 / 4 ） ，進行了對比，從而定量上解釋了目前設計規范引用土力學承載力公式值偏於保守的這一情況；根據本文作者多年從事現場地基工程振動試驗及相關課題的研究工作，本文以截頭錐模型模擬地基，對地基（巖基）承載力的動測法進行了研究，為各類地基（包括巖基） ，匯總了動力分析和檢測川的參數：針對日前巖土工程界應用樁基設計規范中的難點? ?樁端巖基承載力的確定問題，從巖石室內單軸抗壓強度確定、基於彈塑性模型的有限單元法計算、土力學計算及深斤載荷試驗四方面進行了深入討論；本文作者根據多年現場載荷試驗的工程實踐，對深井荷試驗裝置的核心部分? ?反力裝置，設計了側壁支撐反力加載系統，該加載系統具有實用、簡便、穩定及安個等優點。

The current chinese foundation design code gbj7 - 89 use limit equilibrium theoiy with elastic soil stress distribution to give out bearing capacity design value calculating fonnula and use elastic soil model to evaluate foundation settlement. according to the above theories, code gbj7 - 89 gives the correlative terms. but these do not accord with the practical mechanism of loaded soil below the shallow foundation and the elastoplastic property of natural soil so defects exist

我國現行規范gbj7 - 89將這兩者分開考慮，其計算地基承載力設計值的公式是根據彈性地基中應力分佈及土的極限平衡狀態理論為依據而得出的，求地基的沉降變形時則視土體為彈性，這些理論對地基及土的假設與淺基礎地基的實際工作狀態及天然土體的非線性、彈塑性存在一定的偏差。

10 zadeh l a. fuzzy sets and information granularity. in advances in fuzzy set theory and applications, gupta m m, ragade r k, yager r r eds., amsterdam : north holland, 1979, pp. 3 - 18

因此在實用上，不管是數據型態的知識，物理定律方程式，數值或語義輸入變量，都能整合進限制式的模糊塑模系統中，進行知識的表達與推演。

From the feature of the force and deformation of the tpih, 5 different elements are used to mesh the different zones of the tube, which are structural beam 3d elastic 4, structural pipe plastic straight 20, structural pipe elastic elbow 18, structural shell elastic 4 node 63 and contact 3d pt - to - surf 49 ; the contact problem is assumed to be flexible - to - flexible ; the temperature field is assumed to be body load. a mechanical model corresponding to reality has been established for numerical simulation. based on the above, the 3 - d fem numerical simulation of tpih has been carried out by using the ansys program

針對加熱彎管過程的受力和變形特點，採用三維梁單元、三維塑性直管單元、三維彈性曲管單元、三維殼單元與三維點對面接觸單元等5種不同的單元分別對管毛坯不同區域進行劃分，並對接觸單元採用柔體-柔體的處理方法，將溫度場作為體載荷處理，建立了符合實際的加熱彎管問題數值模擬力學模型：在此基礎上，應用商用軟體ansys對加熱彎管過程進行三維有限元模擬與研究，獲得了成形時推力、彎矩、支撐力大小及其變化趨勢。

The first stage is primary slip then followed by secondary slip ; the last stage is due to dislocation passing the slips. the cyclic stress strain ( css ) curve exhibits a stronger hardening occurred in cyclic plastic deformation than that in tensile test

建立了拉伸和應變疲勞的有限元模型，使用基於晶體滑移模型的數值方法，對晶體內部滑移系的啟動以及滑移繫上的分解切應變、切應力這些無法試驗觀測的變量進行計算，分析它們對晶體塑性變形的不同影響。

Relating closely to the main problem of the high sidewall and wide span underground cavities excavation stability of xiluodu hydroelectric project, the evolution characters of geo - stress field in deep - cutting gorge and the whole features of the stress field, strain field and plastic failure zone around the underground chambers after excavation are studied systematically in the dissertation, based on a great deal of data gathered in field investigation and taking the flac3d v2. 0 software as basic computation tools. meanwhile, in the course of research, the new methods of dynamic numerical simulation are summarized and applied. furthermore, the effects of rock mass qualities, initial geo - stress field and excavation procedure on surrounding rock mass stability are discussed

本文緊密結合溪洛渡水電工程大跨度、高邊墻復雜地下廠房洞室群，施工開挖過程中和開挖后圍巖穩定性研究這一重大課題，在詳盡的野外地質調查工作和對大量基礎地質資料的整理與分析基礎上，以目前國際工程地質界公認的最新通用軟體flac ~ （ 3d ） 2 . 0版作為基本計算工具，從整個壩區地應力場的研究開始，通過動態數值模擬分析這一新的模擬思路，系統地研究了深切峽谷區地應力場多階段的特徵和演變規律，進而對左、右岸地下廠房洞室群開挖全過程中圍巖應力場、變形場和塑性破壞區的變化特徵，進行了全過程動態數值模擬研究，並詳細討論了圍巖質量、初始地應力場、施工開挖順序對大型地下洞室群圍巖穩定性的影響。

This text is divided into totally three part, the first part clarities mainly the connotation of credit, the meaning transformation and present application. emphasizing on the importance of the corpus credit diathesis in modem society based on the foundation of existing theoretical outcome. furthermore. the text delimitates the connotation of the credit diathesis, induces the feature of using the credit, namely the three greatest features that are made up of objectivity and subjectivity, explicit ages and plasticity ; the author analyzes closely the credit diathesis of students that is very beneficial for further modem social safety, healthy development, building of the fashion of credit moral, purifying educational and academic circumstance and so on

本文共分三部分，第一部分主要在認真吸取現有理論成果的基礎之上，經過分析和調查研究闡明了信用的內涵及其含義的演變，以及在今天生活中的應用，突出主體信用素質在現代社會的重要性，在此基礎之上比較科學地界定了信用素質的內涵，歸納信用素質的特點，即客觀性和主觀性、鮮明的時代性和可塑性三大特點。第二部分比較深入的分析了培養大學生信用素質對于促進現代社會的健康發展、信用道德風尚的建設、凈化教育環境和學術環境等具有的巨大價值，以及對培養合格人才具有非常重要的意義。

The explicit finite element method ( fem ) based on the varying time - step was selected to analyse the dynamic roll - pass process ; the nodes on the leading face of the steady - state elements set was extracted and projected onto a plane to give the required mesh, also called the origin mesh ; the implicit fem was selected to analyses the inter - pass transient thermal process ; a geometric part from the mesh was generated and meshed by using the quadrilateral elements, a heat transfer analysis was selected to transfer the node temperature data ; a new model was created by using hexahedral elements, mapping the node temperature and the equivalent plastic strain on the integration points

利用基於變步長中心差分格式的顯式積分方法分析瞬態軋制過程；提取穩態單元集節點形成截面網格；利用隱式積分方法分析軋制道次間隙瞬態溫度場；對型鋼斷面進行平面四邊形網格劃分並映射節點溫度數據；利用六面體單元構建有限元分析模型，映射單元節點的溫度、積分點的等效塑性應變，進行數值分析。

Abstract : thermally induced stress and the relevant warpage cause by inappropriate mold design and processing conditions are problems that confounded the overall success of injection molding. a thermorheologically simple thermoviscoelastic two - dimension material model is used to simulate the residual stress and warpage within injection molded parts generated during the cooling stage of the injection molding cycle. the initial temperature field corresponds to the end of the filling stage. the fully time - dependent algorithm is based on the calculation of the elastic response at every time step. numerical results are discussed with respect to temperature and pressure

文摘:不均勻的熱殘余應力及其變形是注塑成型加工中常見的工程問題之一.應用熱流變簡單材料的二維熱粘彈本構方程得到的遞推公式，數值模擬了成型中的熱殘余應力及其翹曲變形，並用數值實驗討論了溫度、壓力對注塑件殘余應力及變形的影響，發現溫度變化不均勻是注塑件翹曲變形的最主要原因，其影響遠大於壓力的作用，與工程實驗的結論一致

The principal stress value arised alteration, the magnitude of stress closed to 25 ~ 32mpa, its influence scope was within the scope outside of tunnel opening 10 ~ 15 meter, maximum tense focused at vault and middle of floor about half meter. shearing stress focused at corner of vault and wall, always been sheared

主應力量值也發生了較大改變，壓應力可達25 32mpa ，其影響范圍在隧道邊墻外10 15m ；拉應力集中在拱頂和底板中部約0 . 5m范圍內，最大可達10mpa ；在拱腰和墻腳常為剪應力集中區，易發生塑性剪切破壞。

Some people believe that bean curd tofu is just bland health food, but great cooks and gourmets can attest that the blandness is what makes bean curd a great cooking ingredient. the beauty of bean curd is that it absorbs the flavours of accompanying ingredients. but this creates the challenge of

豆腐細膩滑潤，入口即溶，而且營養豐富，是老少皆宜的美食它的煮法更是千變萬化，可塑性極高，紅燒煮炒炸煨燜蒸，樣樣皆能，無論作為主菜抑或配菜，都有它的欣賞價值，無怪乎香港人愛吃的食品中，豆腐總是榜上有名。

3. based on the interrelations of flow stress, strain rate and deformation temperature, the four constants of 7055 aluminum alloy can be calculated during the deformation process. 4

）和變形溫度t之間的相關性，求出了7055鋁合金高溫塑性變形的四個材料常數：結構因子a ，應力水平參數，應力指數n和變形激活能q值。

A developed measuring system and test method of green sand properties are introduced. by means of measuring the standard molding sand specimens, the dynamic curves of stress - strain can be quickly and accurately plotted out and several parameters, which represent the characteristics of molding sand, can be tested during the process of compressive deformation. in this brand new method of property measurement two new concepts of viscoelastic parameter and plastic deformation threshold are put forward

介紹了一種研製的型砂性能檢測系統與測試方法，通過對標準砂樣的測試，能迅速、準確地測得砂樣受載過程中的應力應變的動態關系曲線及反映型砂本質特徵的幾項性能參數，這是型砂性能檢測領域中的新探索，其中型砂粘彈性指標及塑性變形臨界值乃是型砂性能方面的新概念。

From experimental result, i preliminarily know that eps is good thermal insulation material because the absorption of water is low and heat insulation is good, it is practicable at preserving temperature field of frozen earth roadbed and bringing frozen disaster under control ; second, according to the analysis of the eps that is applied into practical project, i have studied the practical effect which eps preserve roadbed temperature field, and the influence that was made after building field. i have get that eps can influence moisture content and frozen upper limit, through practical measuring data, i have studied freezing and expanding quantity and melting and submerging quantity during a complete frozen and melting cycle as well as have expanded and proved the practical application effect of eps with some reference significance to deep research of some connected problems. finally, through computer data analysis, setting up the analytical model of finite unit, i have simulated the temperature field of roadbed heat preservation, then expounded and proved that the height of embankment influenced the effect of thermal insulation material

其一是對聚苯乙烯泡沫塑料（ eps ）保溫板以及天然路基土層、路堤填料進行了室內試驗分析，結合國內外現在的有關科研成果，綜合確定其各項特徵參數；從試驗結果初步認識到聚苯乙烯泡沫塑料是一種吸水率低，隔熱性好的保溫材料，在凍土路基溫度場的保護和凍害治理方面是可行的；其二通過eps保溫板在現場工程實踐中的應用分析，研究了保溫板在保護路基土層溫度場的實際效果以及修築路堤后造成的影響，保溫板對土體含水量、凍結上限的影響，通過實測資料，研究了在一個完整的凍融周期內整個路基的凍脹量和融沉變形量，論證了保溫板的實際應用效果，對有關問題的進一步研究和相關工程設計具有參考意義；其三，通過計算機數值分析，建立有限元分析模型，對保溫路基的溫度場進行了模擬計算，論證了路堤高度對保溫材料效果的影響。

As a typical result of modernity, cultural fashion is unknowingly changing people ' s daily behaviors, audio and video experiences, attitudes of life and concepts of value and even reshaping people ' s forms of existence

摘要作為現代性的一種典型後果，文化時尚不知不覺地改變著人們的日常行為、視聽觀聞、生活態度和價值理念，甚至在更深度層面上重塑著人們的存在樣態。

According to elasto - plasticity theory, with the help of finite - method program ansys, the paper undertakes the computer analogue tests about the bearing capacity of pile tip arranged by orthogonal principle, and attains the relations of pile - tip bearing capacity to embedment depth, pile diameter, cohesion, internal friction angle and modulus of deformation. by the means of mathematical statistic, regression equation of the ultimate bearing capacity calculated by finite element method is gained through the regression analysis of 81 group data from the computer analogue tests. by comparison and analysis of the values calculated by finite - element regression equation and the values of in situ loading test, the regression equation is gained which calculates the size effect for base resistance of large diameter pile

根據彈塑性理論，運用大型有限元軟體ansys按正交設計理論對樁端承載力進行模擬計算，獲得樁端承載力與樁長（埋置深度） 、樁徑、粘聚力、內摩擦角及變形模量等主要影響因素的關系，並採用數理統計方法，對81組ansys模擬試驗結果數據進行回歸分析，得到有限元法確定樁端極限承載力的回歸公式，並將有限元法回歸公式計算值與現場小壓板載荷試驗值進行比較分析，得到大直徑樁端阻的尺寸效應系數計算公式。

After pretorsion the successor tensile yield limit and strength limit both improved very highly, but the trend of the increase of the strength limit was suspended till the pretorsional capacity reached 17, when the pretorsional capacity was greater than17 ( prestrain value was 81. 19 % of total strain ), the successor strength limit rapid failed and approached the yield limit. this illustrate the a3 steel specimen translate from plasticity into friability after pretorsion strengthen. when the specimen was operated by tension - torsion action, the yield limit had very large improved, but the strength limit changed very little. furthermore, the trend of the increase of the strength limit was suspended till the pretension capacity reached 0. 25 ( prestrain value was 66. 93 % of total strain )

A3鋼試件在預扭轉后，后繼拉伸屈服極限和強度極限均有很大提高，但強度極限的增大趨勢到預扭轉量為17為止，預扭轉量大於17 （預應變值為總應變的81 . 19 ）后強度極限迅速下降，與其屈服極限接近，這說明a3鋼試件經預扭轉強化后逐漸由塑性轉化為脆性。該預應變值為a3鋼試件的韌脆轉變點。 a3鋼試件在拉伸-扭轉作用下，屈服極限有很大提高，但強度極限沒有多大改變，而且，屈服極限的增大趨勢到預拉伸量為0 . 25應變（預應變量為總應變量的66 . 93 ）后就不再增加。

Under varied loads such as cyclic and / or transient loading, soil structures or foundation will induce permanent and / or fluctuating plastic deformations. such plastic deformations are cumulative and / or alternating in nature with increase of time of loading during a sequence of cyclic loading. if the resulting accumulated deformations is limited within a given bound or the alternating deformations will be adapted to a given plastic state after a certain cycle numbers or a certain period of loading, the soils will be in shakedown state

在復雜變值荷載作用下，結構有可能出現兩種狀態：一種是在若干次載荷循環之後，塑性變形趨于穩定，在此後繼的載荷循環中結構表現為純彈性響應，這種狀態稱為安定狀態（ shakedown ） ；另一種則是塑性流動一直持續地發展或不斷反復，直至結構破壞，結構的破壞有兩種型式：一種是由塑性應變的累積引起的增量塑性破壞；一種是塑性變形多次反復引起的疲勞破壞，也稱為交變塑性破壞。

Method for measurement of cavity volume fraction of superplastically deformed metallic materials

超塑變形金屬材料孔穴體積比值的測量方法