塗敷金屬 的英文怎麼說
中文拼音 [túfūjīnzhǔ]
塗敷金屬
英文
metallising- 塗 : Ⅰ動詞1 (抹) spread on; apply; smear 2 (亂寫或亂畫) scrawl; scribble 3 (抹去) cross [blot; s...
- 敷 : Ⅰ動詞1. (搽上; 塗上) apply 2. (鋪開; 擺開) spread; lay out 3. (夠; 足) be sufficient for Ⅱ名詞(姓氏) a surname
- 金 : Ⅰ名詞1 (金屬) metals 2 (錢) money 3 (古時金屬制的打擊樂器) ancient metal percussion instrum...
- 屬 : 屬名詞1 (類別) category 2 [生物學] (生物分類系統上所用的等級之一) genus 3 (家屬; 親屬) fami...
- 金屬 : metal
-
The direct chiral separation of ( ? 3 - s ) - bridged racemic metal clusters was performed on cellulose - tris ( 3, 5 - dimethylphenylcarbamate ) chiral stationary phase ( cdmpc - csp )
摘要在自製的塗敷型纖維素三( 3 , 5 -二甲基苯基氨基甲酸酯)手性固定相上直接拆分了? 3 - s蓋帽的外消旋四面體金屬簇合物。Septic tanks, bituminous - coated metal
瀝青塗敷的金屬化糞池Welding consumables - covered electrodes for manual metal arc welding of non - alloy and fine grain steels - classification
焊料.非合金鋼和細粒鋼的手工金屬電弧焊接的塗敷焊條.分類Welding consumables - covered electrodes for manual metal arc welding of non alloy and fine grain steels - classification
焊料.非合金鋼和細粒鋼用手工金屬電弧焊接的塗敷焊條.分類Welding consumables - covered electrodes for manual metal arc welding of non - alloy and fine grain steels - classification iso 2560 : 2002 ; german version en iso 2560 : 2005
焊料.非合金鋼和細粒鋼的手工金屬電弧焊接的塗敷焊條Covered electrodes - determination of the efficiency, metal recovery and deposition coefficient
塗料焊條效率金屬回收率和熔敷系數的測定Iso 2401 covered electrodes ; determination of the efficiency, metal recovery and deposition coefficient iso 2401 : 1972 ; german version en 22401 : 1994
塗敷焊條.效率金屬回收和熔敷系數的測定In order to overcome the influence of the technology factor in active molybdenum - manganese metallization, the formulation, raw material treatment, painting method and sintering process are improved in alumina ceramics metallization, which can raise the technique level, product quality and uniform
摘要針對影響氧化鋁陶瓷活化鉬錳法金屬化的工藝因素,在配方、原料處理、塗敷方式、燒結等方面進行改進,提高工藝水平,保證質量穩定性、一致性。Pressed metal plates, the water board and the whole board should be fixed angle reliable, strong, anti - corrosion coatings and sealing material coating installation intact, connector size, spacing and the state should comply with the design requirements of the standard
壓型金屬板、泛水板和包角板等應固定可靠、牢固,防腐塗料塗刷和密封材料敷設完好,連接件數量、間距應符合設計要求和國家現行有關標準規定。分享友人