塗料缺陷 的英文怎麼說

中文拼音 [túliàoquēxiàn]
塗料缺陷 英文
coating defect
  • 塗 : Ⅰ動詞1 （抹） spread on; apply; smear 2 （亂寫或亂畫） scrawl; scribble 3 （抹去） cross [blot; s...
  • 料 : 名詞1 （材料; 原料） material; stuff 2 （喂牲口用的穀物） feed; fodder 3 （料器） glassware 4 （...
  • 缺 : Ⅰ動詞1 （缺乏; 短少） be short of; lack 2 （殘缺） be missing; be incomplete 3 （該到而未到） be ...
  • 陷 : Ⅰ名詞1 （陷阱） pitfall; trap2 （缺點） defect; deficiency Ⅱ動詞1 （掉進） get stuck or bogged do...
  • 塗料 : coating material; paint; coating; daubing; dope; moldwash
  • 缺陷 : defect; fault; faultiness; vitium; lesion; flaw; disorder; imperfection; drawback; blemish
  1. This article analyzes the reason why there are defects on the film surface of powder coatings, and introduced the specific application of ebs in powder coatings

    摘要分析了粉末塗料塗膜表商產生缺陷的原因，介紹了乙撐雙硬脂酰胺（ ebs ）在粉末塗料中的應用。
  2. By improving foundry method, controlling composition, choosing appropriate inoculant and using te - coating, the shrinkage defect could be reduce effectively

    通過改進鑄造工藝、控制鐵液成分、選擇合適的孕育劑、使用碲塗料等綜合控制手段，能有效降低縮松缺陷率，防止缸蓋的滲漏現象。
  3. ( 5 ) glassy oxide film of samples processed by mevva al / piid si covered the surface of sic coating thickly and uniformly, and left few holes as a result of a good ability of sealing, which made weight loss of sic - c / sic smaller in air at1300

    （ 5 ） mevva源注入al再piid （等離子源全方位沉積） si塗層，玻璃氧化層厚而均勻，愈合性能好，孔洞少，對塗層缺陷有最佳的改性效果。復合材料在1300空氣中的氧化失重顯著降低，甚至出現增重。
  4. The results show that the heat preservation coating and its proper thickness are favorable to the enhancement of filling mold speed of aluminium alloy ; the higher the pouring temperature is and the larger the ratio of hollow areas of vertical pouring is, the faster the speed of filling mold of aluminium alloy is ; if the mold is too thick or too thin, it may decrease the speed of filling mold ; the proper length and the area of vertical pouring are favorable to the enhancement of the speed of filling mold ; although negatire - pressure may improve filling the speed, too high negatire - pressure may enlarge the flaw in casting

    結果表明：保溫塗料及一定的塗層厚度有利於提高鋁液的充型速度；澆注溫度越高、直澆道空心面積率越大，鋁液充型速度越快；模樣厚度太厚或太薄，均會使鋁液充型速度降低；一定的直澆道長度及直澆道面積有利於提高鋁液的充型速度；施加負壓會使鋁液的充型速度大大提高，但負壓過大會增大鑄造缺陷。
  5. Methods of test for paints - evaluation of paint and varnish defects - rating of degree of chalking by tape method

    塗料試驗方法.第h6部分:塗料和清漆缺陷評定.沙帶試驗法測定粉化度額定值
  6. Continuous carbon fiber reinforced silicon carbide ceramic matrix composites ( cysic ) are considered as the most promising thermal structural candidate materials for aerospace, energy and nuclear technologies etc. as a key technology for improving high - temperature structural applications of the materials, oxidation protection with anti - oxidation coating system had being paid more and more attentions

    連續碳纖維增強碳化硅陶瓷基復合材料（ c sic ）是一種極具潛力的高溫結構復合材料，在航空航天、能源及核技術等領域有著廣闊的應用前景。為了推進材料的高溫應用，對防氧化塗層已開展了廣泛的研究，但是對目前廣泛採用的cvdsic塗層的缺陷控制鮮有研究。
  7. Iso 4618 - 1, 2 ： 1984, “ paint and varnish ? vocabulary, ” part 1 : general terms ; part 2 : terminology relating to initial defects and to undesirable changes in films during ageing

    1984 「塗料、清漆?詞匯」部分1 ：總則；部分2 ：最初缺陷和在老化條件下，漆膜不合適變化的術語「 。
  8. Paints and varnishes. evaluation of degradation of paintcoatings. designation of intensity, quantity and size of common types of defect. part 4 : designation of degree of cracking

    塗料和清漆.塗料表層剝蝕評定.常見缺陷的尺寸數量和程度的名稱.第4部分：裂度名稱
  9. To counter shortcomings such as oxidation, deform and getting an electric shock of resistance wire of traditional electric stove, this thesis developed a sealing coating for the traditional stove, including selecting material, burden and design of working technology, sample and spread sample have been prepared

    本文針對傳統電爐電阻絲容易氧化、變形、易發生觸電危險等缺陷，並從生產成本要求入手，研製了電爐用封裝塗層材料，包括塗層材料的選材、配料及加工工藝的設計，並據此制備試樣及塗覆樣品。
  10. Preparation of steel substrates before application of paints and related products - test methods for metallic blast - cleaning abrasives - part 5 : determination of percentage defective particles and of microstructure

    塗覆塗料前鋼材表面處理噴射清理用金屬磨料的試驗方法第5部分：缺陷顆粒百分比和微結構的測定
  11. Attentions have to be paid to coating ingredient, smearing, sand filling and compaction for metal seeping defect prevention

    闡明了為防止滲金屬缺陷，在塗料配製、塗掛、加砂緊實中應注意的問題和具體工藝。
  12. Paints and varnishes - evaluation of degradation of paint coatings - designation of intensity, quantity and size of common types of defect - rating of degree of chalking by tape method

    塗料和清漆.漆膜降解的評定.一般性缺陷程度量值和大小的規定.粉化等級評定用膠帶法
  13. Paints and varnishes - evaluation of degradation of paints coatings - designation of intensity, quantity and size of common types of defects - part 6 : rating of degree of chalking by tape method

    塗料和清漆.塗料塗層降解的評價.常見缺陷類型的程度量值和規模評價的標識.第6部分:用膠帶法測定粉化等級
  14. Paints and varnishes. evaluation of degradation of paint coatings. designation of intensity, quantity and size of common types of defect. part 5 : designation od degree of flaking

    塗料和清漆.塗料表層剝蝕評定.常見缺陷類型的尺寸數量和程度的名稱.第5部分：剝落度名稱
  15. The main properties of new alcohol based spraying coatings for green sand mold are superior to the abilities of internal and outside coatings of the same kind, the surfaces of castings that are produced used new alcohol based spraying coatings are smooth without adhering sand and gas - hore

    粘土濕型砂鑄造新型醇基噴塗塗料的主要性能達到了國內外同類產品領先水平；生產的高錳鋼、可鍛鑄鐵和灰口鑄鐵產品表面光潔，無粘砂、氣孔等缺陷。
  16. Preparation of steel substrates before application of paints and related products - test methods for metallic blast - cleaning abrasives - determination of percentage defective particles and of microstructure

    塗料和相關產品使用前鋼基體的預處理.噴射金屬清理磨料的試驗方法.缺陷顆粒的百分比和微結構的測定
  17. Popping a paint defect resembling fine blistering. popping is usually caused by organic solvents trapped during the film cure

    水泡塗料缺陷，類似小水泡。水泡通常在塗膜固化過程中由於有機溶劑集結面形成的。
  18. Coating cracks and defects are main reasons for the limited oxidation resistance of sic - c / sic. in this thesis, surface modification of sic coating was carried out with physical vapor deposition ( pvd ) and ion implantation & deposition, using al, b and si. effects of the modified coatings on the oxidation resistance of sic - c / sic were studied with sem, xrd and aes and so on

    本文採用了物理氣相沉積方法和離子注入沉積方法，以al 、 b 、 si為改性元素，對sic塗層表面進行改性，封填裂紋和缺陷；結合掃描電鏡（ sem ） 、 x射線衍射（ xrd ）和俄歇能譜（ aes ）分析，研究了改性層對sic - c sic復合材料抗氧化性能的影響。
  19. Ground on the knowledge of the form mechanisms of the coating defects, the research work proposed some thoughts related to preparation / deposition process to control the coating defects. based on observation of micro - morphologies of the coatings, combined with relative weight change in oxidation, the effects of these modifications on coating defects control and the behaviors of 2d c / sic at constant temperatures in air condition were investigated. the main contents and conclusions are as follows : 1

    本文從多層cvdsic塗層缺陷形成的根源出發，通過塗層制備工藝進行塗層缺陷控制；以對塗層顯微形貌的觀察為基礎，結合氧化重量變化率，研究了不同塗層改性工藝對多層cvdsic塗層面缺陷的影響以及對2dc sic復合材料恆溫氧化行為的影響，主要研究內容與研究結果如下： （ 1 ）研究了多層cvdsic塗層的2d和3dc sic復合材料在空氣中的恆溫氧化行為，表明2d和3dsic ? c sic在空氣中表現出類似的氧化動力學行為。
分享友人
分享到 Line

分享到臉書