壓制機的模環 的英文怎麼說
中文拼音 [yāzhìjīdemóhuán]
壓制機的模環
英文
pressing ring-
Depend on the comprehensive analysis and study of the structure, principle, and exterior characteristic of the motor, through the methods of system modeling and digital simulation analysis, two kind of control device that work for the low voltage ( lvdc ) and the high voltage ( hvdc ) in avigation are researched respectively. point to the control technique of close - loop speed stabilization at a limited adjustment speed range, we bring out the close - loop speed control method that using the rotor position sensor indirectly measure the speed of the motor
在全面分析了稀土永磁無刷直流電動機的結構特點、工作原理、運行方式以及外部特性的基礎上，通過系統建模和數字模擬分析，分別針對航空低壓直流（ lvdc ）和高壓直流（ hvdc ）兩種電動機構用永磁無刷電動機，在小范圍轉速連續調節下的閉環穩速控制技術進行了詳細理論研究，提出了利用轉子位置傳感器信號間接測量電機轉速進行電機轉速閉環穩速控制的策略。The control system of furnace " s temperature has been widely used in every walk of life, as an important link of repair and manufacture of the electrical equipment such as electromotor transformer etc., soaking lacquer drying craft has some especial requests on drying crafto this article starts with the analysis of drying chamber " s configuration, analyzed its configuration limitation and control function limitation according to the factory " s situation and advances the conception of heated air drying circulation, in addition, this article adopts an intellectualize a / d module, a development sampling tuning - voltage circuit, and presents the method to measure online the insulation resistance of products in order to improve constantly products quality
而浸漆乾燥工藝作為電機、變壓器等電氣設備的修理、製造中的重要環節之一，對乾燥過程的質量要求有一定的特殊性。該文從乾燥爐的結構分析入手，聯繫到工廠的實際情況分析了結構功能缺陷和控制功能缺陷，提出了熱風循環乾燥的概念，同時，選擇了較為先進的a d板卡、熱電阻信號調理板等專業化智能卡，運用數字pid控制技術，構成了一個較有特色的計算機控制系統。此外，該文還從保證乾燥品質量的角度，採用智能化交流模塊和自製采樣調壓電路的方法，提出了在線檢測產修品的絕緣電阻的方法和手段，以確保企業產品質量不斷提高。Comparing and analyzing the synchronous control strategy, which brings up the new method to control the double un - symmetry jars proceed synchronously with the combination of proportional valve and servo valve, which forms closed loop control ; basing on the above methods, models are made to get mathematics models of position control system and to analyze system model theoretically by using pid controller, we can realize regulating parameters, minimizing synchronous errors and enhancing the dynamic performances ; the simulink tool box in matlab software is used to imitate the system according to the model, which not only makes the result visual and easy to adjust the parameters in interactive way but also lets us understand the effects of different parameters and optimizes the dynamic properties. the theory of plc control in dshp is discussed after advanced understanding of the system movements. hardware design and general regulation are given on the base of siemens company products s7 - 200 plc
本文根據大量的國內外文獻，對研配液壓機的工作原理及設計結構進行了簡介；對位置同步的控制方法進行了比較分析，提出比例閥和伺服閥復合控制的閉環結構來對非對稱雙缸進行同步控制電液比例同步控制方案；在此基礎上著重對比例閥控非對稱缸建模，最後得到位置控制系統的總體數學模型，從理論上對同步系統動態特性進行了分析，並用pid控制器進行參數整定，減小雙缸同步誤差、提高系統的動態響應性能；其中控制性能的分析藉助于matlab軟體中的simulink工具箱，由已建立的數學模型形成模擬模型，得到可視化的模擬結果，從而利於交互方式下調整參數，了解不同的參數對系統的影響，優化同步系統的動態性能；在深入了解系統的動作特性后，對plc控制研配液壓機的原理進行了探討，針對siemens公司s7 ? 200型plc給出了硬體設計的總體規劃，編制出研配液壓機動作控製程序，在編程中著重研究位移傳感器與plc的通訊、雙缸同步運行的pid控制在plc上的實現及bcd碼撥盤輸入程序的植入問題。Vvvf door controller frequency converter makes lift door installation easier and more convenient as its control center is the internationally advanced engineering 16 digital micro computer and it operates with the fully digital spwm modulation techniques, with igbt module as the output power drive and with voltage, current and speed under fully digital closed circuit control ( the door controller ' s operation parameters are inputted by means of the keyboard )
Vvvf控制門機變頻器採用當今國際上先進的工控16位微型計算機為控制核心，採用了全數字spwm調制技術， igbt模塊作輸出功率驅動，電壓、電流、速度全數字閉環控制（門機的運行參數均可通過鍵盤設置輸入） ，從而，使門機的安裝調試更加簡單，方便。According to the control rod hydraulic drive mechanism ( crhdm ) and the characteristics of its hydraulic cylinder seal structure, the leaking ways of the hydraulic cylinder piston ring seal were analysed, its theoretical calculation model was built and its flow resistance formula based on the calculation model of differential pressure at the hydraulic cylinder piston ring seal was deduced
摘要根據控制棒水壓驅動機構水壓缸活塞環密封結構的特點，分析了水壓缸活塞環的泄漏途徑，建立了活塞環密封泄漏流阻的理論計算模型，並結合水壓缸活塞環密封處的壓差計算模型，推導出水壓缸密封結構的流阻計算公式。The paper lays a strong emphasis on discussing the realization of the autocontrol of raster scanning of the scanner in x - y dimension, the " tapping " of the cantilever of the tappingmode afm by a direct digital synthesizer. then a method of parallel communication between dsp and pc in epp mode is given. finally, the author discussed the digital pid closed loop control of the scanner in z - direction, the automatic approaching of the tip using step - motor, and also some electro - magnetic interferences
論文首先簡單介紹了掃描探針顯微鏡的發展、分類、工作原理及應用；接著對ti公司的tms320vc5402dsp的特點及外圍擴展作了簡單介紹；然後分章節重點講述了利用vc5402dsp實現掃描探針顯微鏡的核心部件? ?壓電陶瓷管的x向和y向的光柵掃描控制；藉助直接數字集成器（ dds ）實現輕敲式原子力顯微鏡的微懸臂的「輕敲」 ； vc5402dsp的主機介面（ hpi ）與pc機在增強并行口（ epp ）模式下的通信；論文最後還介紹了掃描管z向的數字pid閉環控制，步進電機的自動進針，並對實際出現的一些電磁干擾問題作了討論。According to the request of this subject, we have developed the system hardware and software for the slave device and the inspection software running on the pc. in this paper all of the followings is illustrated detailedly, such as the research on the principles of measurement and its realization, three means of water - level measurement that are separately based on photo electricity coder, pressure sensor and potentiometer ; selection of the microchip, we choose an advanced integrated soc ( system on chip ) microchip c8051f021 as the main controller ; realization of signal sampling, processing and its conversion in the mcu ; application of high precision 16 bits adc cmos chip - - ad7705 in our system, designing its interface with the microchip and relevant program ; using a trickle charge timekeeping chip ds1302 in the system which can provide time norm and designing of its i / o interface and program ; additionally, a 4 ~ 20ma current output channel to provide system check - up using ad421. in the system, ad421, ad7705 and the microchip compose spi bus ; to communicate with the master pc, here we use two ways which are separately rs232 and rs485 ; moreover, there are alarm unit, keyboard unit, power supply inspection unit and voltage norm providing unit in the system
針對研製任務的要求，課題期間研製了下位機系統硬體和軟體，開發了上位機監控軟體，其中所作的具體工作包括：測量原理的研究和在系統中的實現，在本次設計中用三種方法來進行水位測量，分別是旋轉編碼器法、液位壓力傳感器法和可變電阻器法；主控晶元的選擇，我們選用了高集成度的混合信號系統級晶元c8051f021 ；實現了信號的採集和處理，包括信號的轉換和在單片機內的運算；高集成度16位模數轉換晶元ad7705在系統中的應用，我們完成了它與單片機的介面設計及程序編制任務；精確時鐘晶元ds1302在系統中的應用，在此，我們實現了用單片機的i o口與ds1302的連接和在軟體中對時序的模擬，該晶元的應用給整臺儀器提供了時間基準，方便了儀器的使用；另外，針對研製任務的要求，還給系統加上了一路4 20ma模擬信號電流環的輸出電路來提供系統監測，該部分的實現是通過採用ad421晶元來完成的，本設計中完成了ad421與單片機的spi介面任務，協調了它與ad7705晶元和單片機共同構成的spi總線系統的關系，並完成了程序設計；與上位機的通信介面設計，該部分通過兩種方法實現： rs232通信方式和rs485通信方式；系統設計方面還包括報警電路設計、操作鍵盤設計、電源監控電路設計、電壓基準電路的設計。Data inputting and graphinputting module respectively achieve data inputting of first system and electric firstwiring diagram inputting ; secondary scheme design module realizes scheme design ofsecondary loops including control, protection, signal, measure, automotive equipment, operation electrical source and electrical source for substation and power distributionstation, using rule - cased reasoning of expert system ; protective relaying settingcalculation module realizes setting calculation for first equipments which aretransformers, circuitries, capacitors, and electromotors ; secondary equipmentselection module realizes type selection of secondary microcomputer integratedequipments ; graph making out module realizes secondary drawings making outautomatically representing design production using case - cased reasoning of expertsystem and the drawings can be edited and modified under the secondary developedautocad environment
數據輸入和圖形輸入模塊分別完成一次系統資料錄入和電氣主接線圖的輸入;二次方案設計模塊利用專家系統基於規則的推理實現變配電所各二次迴路的方案設計，包括控制、保護、信號、測量、自動裝置、操作電源和所用電源;繼電保護整定計算模塊實現主設備的整定計算，包括變壓器、線路、電容器和電動機;二次設備選型模塊實現二次微機成套裝置的型號選擇;圖形生成模塊利用專家系統基於實例的推理實現代表設計成果的各類二次圖紙的自動生成，生成的圖紙可以在二次開發的autocad環境下進行編輯和修改。Prototype of the symmetrical typical voltage space - vector of open - loop variable frequency speed system is designed by using the tms320f240 digital controller and the ipm ( intelligent power model ), with which had a exam on the motor and the experimental results are also given. from the results we can conclude that the results are according with the theory analysis
利用ipm智能功率模塊，設計了採用基於tms320f240數字控制器的對稱空間電壓矢量的開環變頻調速系統的原理樣機，對電機進行了空載實驗，給出了它們的實驗結果，實驗結果和理論分析相一致。This paper expatiated that the mathematics models of ac motor is higher order, non - linear and closed coupling, multivariable input - output system. and introduces the principle and the algorithm of sine pulse width modulation ( spwm ), opened - loop space voltage pulse width modulation control ( svpwm ) and field oriented control ( foc ). finally, realized the control strategies of variable - frequency speed regulating using assembly and c language
文中闡述了交流異步電機的數學模型是高階、非線性、強耦合的多變量輸入輸出系統，介紹了交流電機的正弦脈寬調制、開環電壓空間矢量的u / f控制和磁場定向控制的原理及控制演算法，並利用dsp構成控制系統，通過匯編語言和16位定點c語言混合編程的方法實現了上述的變頻調速控制策略。This article describes the plc ’ s using enviroment and the users ’ needs in details, and then tells the differences between the dplc and the troditional plc. it also describes how to decimation and compress the tele - voice, how to deal with the data tunnels, and the multiplex data through the the line which ’ s bandwidth is changeable between 10. 8bps and 28. 8kbps this project uses the programmable vopp chips, the cpld for bus controlling, the fpga and the mcu with high processing ability. all of these ensure the high ability to process the signals and the operations
本文詳細介紹了高壓電力線載波機的使用環境和用戶需求，全數字電力載波機和傳統模擬載波的的差異;按電力調度的需求設計完整的兩路語音、兩路數據的電力線載波通訊機。詳細描述電話語音的采樣，壓縮;數據通道的處理;及在10 . 8kbps 28 . 8kbps可變線路速率通道上的數據復接處理。從實現方法上看，該項目採用專用可編程vopp語音處理晶元， cpld晶元做為總線控制，大規模fpga集成電路，高處理能力的mcu 。4. the hardware of electronic control system is developed. it includes display module whose tasks are man - machine interaction, displaying humidity and temperature, setting humidity, time, date and week, communicating with computer ; power device module which provides power of all modules and drives control equipments to accomplish intention of main control module and can provide zero crossing protection circuit, excess voltage and under voltage protection circuit and excess current protection circuit ; water sensor group, the responsibilities of which are testing the states of water and send the states to scm, then the scm control the water level after judging the states
開發並實現了電控系統的硬體部分，包括顯示模塊：主要負責人機交互，顯示濕度、溫度，修改濕度、時間、日期、星期，和主控模塊通訊；電源驅動模塊：主要提供各個模塊的電源，驅動被控設備，實現主控模塊的意圖，並能實現繼電器的過零保護，過流、過壓、欠壓保護；水位傳感器組：負責測知水位的狀態，並把此狀態送入單片機，單片機經過判斷、處理反過來控制水位，實現水位的閉環控制。Some research about sensorless control of induction motors in recent years has been introduced in chapter one. in chapter two, a field - oriented control system with current regulator and voltage source inverter ( vsi ) is presented firstly, which is proved in theory that the voltage feed - forward decoupler can be omitted, the good decoupled control properties of flux current and torque current is also validated by experiments with speed - sensor based on f240dsp real system
論文第二章從異步電機的基本數學模型入手，介紹了一種基於轉子磁場定向的帶電流內環控制的電壓型逆變器輸出閉環矢量控制結構，在理論上證明了該模型可省略電壓前饋解耦環節，採用f240dsp晶元構建的帶速度傳感器實驗系統驗證了其定子電流勵磁分量和轉矩分量有良好的解耦控制特性。Regard how to structure the control system of sensorless bldcm with dsp - tms320f240 as the centre in this paper, the detailed argumentation course of the motor startup, bemf terminal voltage measurement and control strategy is given out, give and pay concrete details for the software and hardware realization and experimental result. in order to treat the bldcm control system with dsp clearly, the full paper divides into six chapters altogether : chapter one, introduceing the development course, the structure characteristic and operation principle, etc. of bldcm in the introduction ; chapter two, directed against the startup issue of bldcm, the chapter give and publish the rotor measure pulse orients technology for motor startup in detail ; chapter three, proceed with mathematics model of the bldcm, expounding the control schemes ; chapter four, two important devices introducing : dsp ( 240 tms320f ) and power invertor control chip ( ir2131s ) ; chapter five, give and publish the detail of hardwares of control system ; chapter six, by ccs ide of ti, realize the control schemes in the front chapters with software, offere the procedure flow chart of main subroutine and some key place of programming, the experiment result in addition
全文共分六章：第一章、緒論中介紹了bldcm的發展歷程、電機本身的結構特點和工作原理等；第二章、針對五位置傳感器bldcm的起動問題，文中詳細給出了檢測脈沖轉子定位起動技術；第三章、從電機的數學模型入手，詳細論述了反電動勢端電壓法和系統的控制策略；第四章、介紹了硬體實現中的兩個重要器件： dsp （ tms320f240 ）和功率管逆變器控制晶元（ ir2131s ） ；第五章、詳細給出了控制系統的硬體實現細節；第六章、利用ti提供的ccs集成開發環境，將前面章節的控制方案用軟體加以實現，給出了主要部分的程序流程圖和一些編程要點以及實驗結果。On the basis of analyzing the rock mechanics, the bit working circumstance and property in the bottom hole of 6000m deep well, and making use of the former equipment such as a derrick, platforms etc, the paper demonstrates that the research and design of the mechanical device have been established including the high pressure simulating well bore, the high pressure connector between the static well bore and the rotating drill pipe, the high pressure simulating system of circulating fluid and the high pressure desander etc. the produce, control and dynamic analysis of the bottom hole four - dimensional pressure ( over burden, confined, pore and column pressure ) have been studied
本文在對井底巖石的受力狀態以及鉆頭的工作環境和特性加以分析的基礎上，藉助原有的井架、平臺等設備，研究設計了模擬6000米井底壓力壞境的高壓模擬井筒、鉆柱高壓轉聯器、鉆井液高壓模擬系統以及高壓除砂器等機械裝置，並研究了井底四維模擬壓力（上覆壓、圍壓、孔隙壓和液柱壓）的產生、控制及其控制的建模與模擬，從而實現井深至6000米的四維井底壓力環境的模擬。And the converter will work on the strategy of vector control with the definitive direction of the stators magnetic field. also, the thesis develops the algorithm to corroborate the magnetic field ' s direction by the state ' s current and voltage. to validate the theory analysis of bdfg
根據理論分析和模擬的結果，本文提出級聯式無刷雙饋發電機的控制策略是基於定子磁鏈定向的矢量控制方法，並推導了用定子側電壓電流量來確定定子磁鏈方向的演算法，繪制了相應的閉環控制框圖。On the basis of the analysis on spwm modulation mode and transient current control theory, a new method of voltage balance on the capacitors in dc side is proposed, and computer simulation is carried out in matlab
在分析了spwm調制方式和瞬態電流控制原理的基礎上，提出了一種直流側兩電容上電壓平衡的方法，並在matlab環境下進行了計算機模擬。With the aid of these blocks, it is convenient and flexible to make up different kind of automatic - controlled simulating system and so to accomplish different kind of automatic adjusting task. this paper is focused on the construction of the simulation model of ccs by using the contrived control section model. the ccs employs advanced direct energy balance control strategy and can simulate different running patterns such as turbine following boiler pattern, boiler following boiler pattern, etc. two independent control loops : power control and frequency control, are used in the contrivance of deh and they are separately corresponding to the normal condition and the abnormal condition
本文利用開發的控制環節模塊，著重建立了協調控制系統的模擬模型，該協調控制系統採用了先進的直接能量平衡控制策略，並能模擬機跟爐、爐跟機、機爐協調、手動以及定壓和滑壓等運行方式；開發的功頻電液系統模型採用了功率控制和頻率控制兩個獨立的控制迴路，能夠在機組正常運行和啟停時對汽輪機進行控制。There are two functions in the fault injector, one is the realization of digital controller ’ s work environment by simulating the electrical characteristics of sensors and actuators, another function is the control of the fault injection which is realized by the voltage - controlled constant voltages source and relay switch circuit etc. the manage compuer is in charge of the fault mode setting, fault injection process controlling and result data retrieving
在故障注入器上，通過對傳感器和執行機構電氣特性的模擬提供控制器的運行環境，利用壓控恆壓源和繼電器開關等電路實現多種故障注入方法;作為故障注入器上位機的管理計算機，負責故障模式設置、故障注入過程式控制制和結果回收處理。The simulation model of pmsm close - loop control system is presented based on pwm inverter model and switching vector table model set up by the author and pmsm model in matlab. the model is proved correct from the simulation result
然後在自行構造逆變器，開關電壓矢量表等模塊的基礎上，利用matlab中的永磁同步電機模型，實現了永磁同步電機閉環控制系統的模擬模型，模擬結果驗證了方案的正確性。分享友人