套筒壓力 的英文怎麼說
中文拼音 [tàotǒngyālì]
套筒壓力
英文
sleeve force due to centrifugal action-
Promax tension ind corp has long sold and manufactured a variety of custo mized air shafts / air chucks / safety chucks, edge position control systems / epc, powder / air / disk brakes and clutches, ac / dc motor control systems, re - winding / un - winding systems, tension control systems, web inspection systems, automatic color register systems, servo - vector control systems, mmi interface and supervisory control and data acquisition ( scada ) systems and others such as slitting, winding, laminating, extruding, coating, and gravure printing machines, even other auxiliary devices etc. for webs such as paper, films, rubber, textiles and foils
本公司長久以來已經從事製造及銷售有關紙類,薄膜,膠片,紡織品,橡膠等薄片卷材的捲筒物控制糸統周邊設備,諸如氣漲軸,氣漲/安全夾頭,邊緣追蹤器裝置,磁粉/氣壓/碟式煞車器及離合器,交直流轉矩馬達控制系統,收放料車動系統,張力控制裝置,印刷機靜態觀測器,自動套色控制裝置,伺服向量控制系統,人機介面及監控系統及其他有關印刷,貼合,分條,復? ,塗布,上膠,押出,淋膜等產業機械Single spiral crowed syrup machine is applicable to the dehydration that warious low density syrup anticipate and dredge - solve, according to the pulp consistency pass pneumatic equipments to adjust the syrupcrowede pressure, the adaptability is strong ; the spiral stalk and tube of sieves are made of the stainless steel, corrosion - resistant and durable ; operate conveniently, break down the rate low, produce to have great capacity, maintain the expenses low, the best kit equipments that is high and thick to whet
描述:本機適用於各種低濃度漿料的脫水和疏解,可根據漿料濃度通過氣動裝置調整擠漿壓力,適應性強;螺旋軸及篩筒均用不銹鋼製成,耐蝕耐用;操作簡單,故障率低,生產量大,維修費用低,是高濃磨的最佳配套設備。In the end, two illustrated examples - one is two nesting thick cylinders subjected to internal pressure and the other is a shield - driven metro tunnel, were solved with this method successfully
最後,應用給出的方法計算了2個算例內壓作用下2個相套厚壁圓筒接觸和用盾構法修建的地鐵隧道的受力變形。Super percision fluid dispenser, parts ( syringe, nozzle, valve, tank and so on ) and fad system
液體精密定量吐出裝置系統及周邊各種配套精密配件,如針筒,針嘴,點膠閥,壓力罐等Specifications for turnbarrels, tension rods and swaged cable - end connections unified threads for aircraft
飛行器用旋轉套筒張力傳動桿和旋壓鋼索端部接頭On the other hand through the numerical simulation and the theoretical analysis, the characteristics of electro - magnetic implosion and detonation driven implosion have been compared, and it is concluded that the ability of driving liners with the electro - magnetic implosion is much stronger than that of detonation driven implosion
利用計算結果和炸藥驅動內爆進行了比較,並結合理論分析得出了磁壓驅動套筒內爆達到高速的能力要強于炸藥驅動的結論。同時以上述理想導體模型對磁驅動等熵壓縮進行了流體力學數值模擬,從數值模擬的角度論證了磁驅動加載可以進行等熵壓縮實驗。The reduced pressure detector assembly shall consist of two independent torsion spring check modules, a differential pressure relief valve located between and below the two modules, two drip tight shutoff valves, and required torsion spring check modules and relief valve shall be contained within a sleeve accessible single housing constructed from 304 ( sch 40 ) stainless steel pipe with groove end connections
這種減壓檢測器總成應該包括兩個獨立扭力彈簧止回閥模塊,一個位於兩個模塊之間的下方的差壓安全閥,兩個防滴漏關閉閥,並且要求扭力彈簧止回模塊和安全閥應該放置在一個套筒內,要易於接近帶溝槽連接的304 (目錄40 )不銹鋼管的單個外殼。Mpa 250bar 1 2 3. agricultural trailers. single - acting telescopic tipping cylinders. 25 mpa 250 bar series. typles 1, 2 and 3. interchangeability dimensions
農用拖車.套管筒式單動作抓鬥式起重拖車.系列25進氣壓力表This paper discussed the development general situation of the domestic and international super high pressure vessel first, and then the calculative method of stress and the homologous strength theories about the single - layer ordinary round super - high pressure vessel, single - layer autofrettage thick wall round super - high pressure vessel and shrunk - on double - layers round super - high pressure vessels were elaborated systematically
本文在論述了國內外超高壓容器的發展概況的基礎上,較為系統地闡述了單層普通圓筒形超高壓容器、單層自增強厚壁圓筒形超高壓容器、雙層縮套圓筒形超高壓容器的應力計算方法及相應的強度理論。In order to overcome the shortages resulted from hypothesis of small deformation in radial symmetry based on thick - wall cylinder, plane stress and uniform pressure about residual stress around cold - expanded hole, a new model was proposed which takes into consideration the effect of split - sleeve, the different states along thick direction of specimen
摘要針對目前在研究冷擠壓孔邊殘餘應力時,大都採用基於厚壁圓筒的軸對稱小變形、平面應力狀態、孔邊受力為均布載荷等假設所帶來的不足,提出了在三維真實模型狀態下,考慮襯套對孔邊受力的影響、試件在厚度方向上的應力差異等因素。分享友人