套針套管 的英文怎麼說
中文拼音 [tàozhēntàoguǎn]
套針套管
英文
trocar and ca ula-
Brain casing pipe needle
腦套管針Brain exploring trocar and cannula
腦部探測套針和套管Sterile indwelling cannulas with needle and catheter for hemodialysis
血液透析用帶針頭和導管的無菌留置套管Cannula with stylet
帶有通管針的套管Trocar for animals
獸用套管針Trocar and cannula
套針套管Let the part ready for vein puncturing, then antisepsis it. remove the colorful acus s coverand expose the head of bi - direction acus, then puncture veins stanting on15unit of measure
準備靜脈穿刺部位,並予以消毒。拔除彩色針套,暴露雙向針前端,以15度角斜向上進行靜脈血管穿刺。Specification for antral trocars and cannulae
竇套針及套管規范Alarm handsetting wheel tube
鬧拔針輪套管With a field survey of aas, a car rental service business in the suzhou, those theories and methods of job satisfaction were put into practice. a system of measurement aiming at aas staff was designed from aspects of job itself, rewards, support, peer group, corporation management and operation. apart from the above mentioned, some variables, such as staff gender, age, education background and position were also taken into account in the analysis of job satisfaction
本文第二部分是員工滿意度實證分析,在實地走訪和調研蘇州aas汽車租賃企業的基礎上,將工作滿意度調研分析的有關理論與方法運用到實踐中,設計了一套針對aas員工的工作滿意度量表,從工作本身、工作回報、工作支持、工作群體、企業管理、企業經營等六個維度來調研分析aas員工工作滿意度狀況,並對員工性別、年齡、教育水平、職位職務等變量對工作滿意度的影響進行了分析。Accessory devices for sterile single - use intravascular catheters - part 2 : obturators for over - needle peripheral catheters
一次性使用無菌血管內導管輔件.第2部分:套針外周導管管塞The new unit adopts hollow sucker rod working with pump and as fluid passage instead of conventional sucker rod, and uses a new hanger to fix the one - piece barrel rod pump on the casing wall, improving the operation stability of the subsurface pump
針對這種情況,大港油田新世紀機械製造有限公司研製成功一種新型無油管採油裝置,這種裝置以空心抽油桿代替實心抽油桿帶泵工作併兼作出油流道,還通過一種新型懸掛器將整筒抽油泵固定在套管壁上,提高了抽油泵的工作穩定性。Yoke sleeve ? aluminum - bronze yokesleeve has needle type thrust bearings to minimize operating torque
軛架套管?鋁青銅軛架套管配置針形止推軸承,最大程度減少操作扭矩。Yoke sleeve ? aluminum - bronze yoke sleeve minimizes operating torque. larger sizes have needle bearing type thrust bearings
軛架套管?鋁青銅軛架套管最大程度減少操作扭矩。較大通徑的截止閥配置針形軸承類型的止推軸承。Based on the dynamics, a mechanical model calculating the drill string ' s eccentric wear is established, the approximation equation calculating the positive pressure on casing / drill string is derived out, and the major factors affecting the eccentric wear are analyzed
針對深井鉆井中的井口附件套管偏磨問題,以動力學為基礎,建立了鉆柱偏磨力學模型,推導出了套管鉆柱正壓力的近似計算公式,分析了影響偏磨的主要因素。Thoracic cavity drainage casingneedle
胸腔引流套管針In reference to simulation system of air gun firing - spinning tube receiving in 5124 factory bought from america and ad report that harry diamond laboratory has released about simulating setback and spin of fuze in fire, design a new simulation system to simulate setback and spin of fuze in fire, whose diameter are less than 76. 2 mm
在參考5124廠引進的美國空氣炮發射?旋轉管接收模擬系統以及美國哈里?戴蒙德研究所發表的關于引信發射后坐與旋轉環境模擬ad報告的基礎上,設計出一套針對最大外徑小於76 . 2mm引信及引信零部件進行發射后坐與旋轉環境模擬的模擬系統。Aim at the shortage in actual application that the frp pipe flange joint with the steel pipe and steel parts, in consideration of the special advantage of the adhesive boned joint, put forward the method that the steel flange adhesive boned steel pipe or steel part after the steel flange instead the frp pipe flange, or the frp pipe adhesive boned direct with the steel and steel part, it can reduce the stress concentration problem that cause from the different of the descend speed and the hot bulge or freeze coefficient in the applied process. thus reduce the damage number and the maintenance costs of the piping, so this method can have the greatly actual application value
針對玻璃鋼管道與鋼管及鋼管件之間法蘭連接方式在實際應用中的不足之處,考慮到膠接連接的獨特優勢,提出如用鋼法蘭代替玻璃鋼法蘭與玻璃鋼管道膠接后,再與配套的鋼管及鋼管件進行連接,或玻璃鋼管道直接與鋼管(件)進行膠接連接,則可減少玻璃鋼管道在應用過程中與鋼管(件)連接后因沉降速度及凍脹系數均不同而產生的應力集中問題,減少管道的損壞次數及維護成本,有很大的實際應用價值。Aiming at the application of shaft ultrasound imaging in cased well, the scheme improves imaging resolution power and gives the reasons why space resolution power is superior to conventional imaging
在此基礎上,針對井壁超聲成像在套管井檢測的應用實際,建立了提高成像解析度的合成孔徑聚焦成像模型,並對此進行了論證。A measuring system for fast neutron reactors sleeves and fuel pins is designed to regularly examine the main core fuel assembly sleeves and fuel pins in the reactors of a nuclear power station. it is aimed at the evaluation of the reactors performance of fuel pins and assembly and the provision of valuable information concerning the fuel integrity
快堆組件套管及燃料棒測量系統是針對核電站的反應堆中主要燃料部件組件套管和燃料棒的定期檢驗而設計的,其目的是評價燃料棒和組件套管的堆內性能,提供關于燃料完整性的有價值的信息。分享友人