寬度優先過程 的英文怎麼說

中文拼音 [kuāndùyōuxiānguòchéng]
寬度優先過程 英文
breadth-first procedure
  • 度 : 度動詞[書面語] （推測; 估計） surmise; estimate
  • 先 : 名詞1 （時間或次序在前的） earlier; before; first; in advance 2 （祖先; 上代） elder generation; ...
  • 過 : 過Ⅰ動詞[口語] （超越） go beyond the limit; undue; excessiveⅡ名詞（姓氏） a surname
  • 程 : 名詞1 （規章; 法式） rule; regulation 2 （進度; 程序） order; procedure 3 （路途; 一段路） journe...
  • 過程 : process; procedure; transversion; plication; course
  1. This article puts forward a solution named divide - assemble by deducing the size of bp neural network to overcome entering the local best point, the dividing process is that a big bp neural network is divided into several small bp neural networks, every small bp neural network can study alone, after all small bp neural networks finish their study, we can assemble all these small bp neural networks into the quondam big bp neural networks ; on the basis of divide - assemble solution, this article discusses the preprocessing of input species and how to deduce the size of bp neural network further to make it easy to overcome entering the local best point ; for the study of every small bp neural network, this article adopts a solution named gdr - ga algorithm, which includes two algorithms. gdr ? a algorithm makes the merits of the two algorithms makeup each other to increase searching speed. finally, this article discusses the processing of atm band - width distribution dynamically

    本文從bp網的結構出發，以減小bp神經網路的規模為手段來克服陷入局部極小點，提出了bp神經網路的拆分組裝方法，即將一個大的bp網有機地拆分為幾個小的子bp網，每個子網的權值單獨訓練，訓練好以後，再將每個子網的單元和權值有機地組裝成原先的bp網，從理論和實驗上證明了該方法在解決局部極小值這一問題時是有效的；在拆分組裝方法基礎上，本文詳細闡述了輸入樣本的預處理過程，更進一步地減小了bp網路的規模，使子網的學習更加容易了；對于子網的學習，本文採用了最速梯度? ?遺傳混合演算法（即gdr ? ? ga演算法） ，使gdr演算法和ga演算法的優點互為補充，提高了收斂速度；最後本文闡述了用以上方法進行atm帶寬動態分配的過程。
  2. First, according to the demand of vimp for resin system, the reaction kinetics and rheological of up resin are investigated and the optimal content of low additive profile ( lpa ) is determined. then vimp based on a high - permeable medium and grooves are studied by visual experiments, through which the appropriate high - permeable mediums are selected and the parameters of width, depth and spacing for flow grooves and spacing for supply grooves are optimized. furthermore, various factors affecting the mold filling process are discussed and the whole vacuum infusion procedures are described taking examples of the manufacture of a model boat and a sandwich panel in one infusion

    文中首先根據vimp對樹脂體系的要求，對vimp用不飽和聚酯樹脂體系的動力學和流變學性能進行了研究，確定了最佳低收縮添加劑的含量；對高滲透介質型和溝槽型vimp開展了實驗研究，通過可視化實驗優選出較好的高滲透介質，確定了引流槽的寬度、深度和槽間距及主槽的槽間距等工藝參數並進行了優化；對影響充模過程的各種因素進行了詳細的討論，並以模型船和夾芯面板的製作為實例描述了兩種vimp的成型過程；在實驗的基礎上，建立了二維滲漏模型，採用控制體有限元法對高滲透介質型vimp進行了成型過程的計算機模擬計算，通過充模時間和流動前峰的計算值與實驗結果的比較，驗證本文所採用的數學模型和數值方法的正確性，其結果對實際生產具有一定的理論指導意義。
  3. Two 3 - frames - grained scheduling policies are suggested to make good trade - off between processing demands and on - chip buffer demands in software decoding implementation. a static time division multiplexed scheduling / dynamic fixed priority arbitration based 2 - level hybrid arbitration scheme, incorporated with synchronization control, is introduced in this paper to utilize the bus bandwidth effectively and lower on - chip buffer demands in media soc

    提出了一種基於靜態分時復用調度動態固定優先級仲裁的混合二級總線仲裁策略，通過分割總線時間片靜態調度媒體數據流dma傳輸，使之與解碼流程同步配合，有效地分配和使用總線帶寬，降低了片上數據緩存等硬體開銷。
  4. Then a new fixed cycle polling dynamic bandwidth allocation algorithm is proposed to support qos and improve bandwidth utilization in epon. the proposed algorithm consists of two parts : one is scheduling between olt and onus, and the other is scheduling between priority queues in onu

    此演算法將帶寬分配過程分為兩部分，首先是onu之間的調度，即olt給每個onu分配帶寬;其次是onu內部的調度，即onu將帶寬分配給各個優先級隊列。
  5. Then, only a given curve satisfied by the conditions of import and outlet of vane wheel as its modular curve will neglect the middle varying processes of in vane wheel, which reflect microscope properties in some degree - flow properties in boundary layer. leading into the velocity - coefficient unifies the boundary layer and eular theory in the design process of vane, which extends the area of selection of vane ' s curves and provides a valuable object function for the optimization design of vane

    那麼，僅憑一條預先給定的滿足葉輪出入口條件的曲線去來作為葉輪的型線，它必將忽略了這種除了葉輪出入口之外的中間變化過程，而這種中間變化在某種程度來說又反映出微觀特性? ?邊界層流動特性；速度系數的引入，它使邊界層理論和歐拉理論在泵的葉輪設計過程中得到統一；它使選擇葉片曲線的域圍拓寬；它也為葉輪的優化設計提供了一個很有參考價值的目標函數。
分享友人
分享到 Line

分享到臉書