寬度線性 的英文怎麼說
中文拼音 [kuāndùxiànxìng]
寬度線性
英文
width linearity-
Tide is the primary dynamic factor in building tidal flat ; it must be affect tidal creek system on mud flat. therefore, based on the raster image of the year of 2000, the thesis has built correlation equations between average tidal ranges and the density of tidal creeks, the ratio of the width of outlet to the length of low tidal shore, the ratio of the area of tidal creek to tidal basin respectively. the result shows that the former is high well - marked correlation ; the two latter are well - marked correlation
潮汐是塑造潮灘的主要動力因素,它必然與淤泥質潮灘上潮溝系統的發育有密切的關系,為此,本文以2000年的衛片作底圖,對潮溝系的密度、溝口寬度占低潮線長度的比值以及潮溝面積與潮盆面積的比值,分別與平均潮差建立了相關關系,結果發現,潮溝系的密度與平均潮差之間存在著高度顯著的相關性,溝口寬度占低潮線長度的比值和潮溝面積與潮盆面積的比值與平均潮差之間存在著顯著的相關性。The factors limiting the frequency band of the wide - band amplifier are introduced. through analyzing the effects of the intrinsic parameters and parasitical on the frequency characteristics, a method of improving fr of mosfet by using short channel device and making mosfet work at the saturation region through raising vgs is put forward ; the effects of different kinds of circuit configurations on the frequency characteristics and the junction voltage on the voltage pattern circuit, current pattern circuit and frequency characteristics are analyzed. according to the linear theory of transconductance which is applied in the bit circuit, the current pattern amplifier circuit, current transfer circuit and output circuit which consist of mosfet and the wide - band amplifier composed of them are put forward
介紹了限制寬帶放大器頻帶寬度的因素,通過分析mosfet的本徵參數、寄生參數對頻率特性的影響,提出了採用短溝器件、使mosfet工作在飽和區、抬高柵源電壓等提高mosfet特徵頻率的方法;分析了不同電路組態對放大器頻率特性的影響、節點電壓對電壓模電路、電流模電路頻率特性的不同影響,根據應用於雙極晶體管電路的跨導線性原理,提出了採用mosfet構成的電流模放大電路、電流傳輸電路、輸出電路以及由它們所組成的寬帶放大器,獲得了良好的頻率響應。First, it was taken that a discuss about the effects of geometry parameters of each piezocrystal on direction parameters ( main lobe width, side lobe amplitude, elimination of grating lobes ), amplitude of ultrasonic pressure, element viberation pattern, mutual radiation among elements, efficient test regions, ability to keep accurate and near - field distance and so on. based on the direction of ultrasonic field in ulpa deduced by ourselves. in addition, on the base of integrating all kinds of factors, it was put forward that the principle and method for optimized design of geometry parameters of piezocrystals in ulpa transducer, and its design programme and interface were compiled
首先在推導超聲相控線陣換能器聲場的指向性的基礎上,就各個晶片幾何參數對指向性指標(主瓣寬度、旁瓣幅度、消除柵瓣) 、聲壓幅值、陣元振動模式、陣元間互輻射、有效檢測區域、精確控制能力、近場長度等方面的影響進行了論述,並在綜合各方面影響的基礎上,提出了晶片幾何參數優化設計的原則和方法,編寫了設計程序和界面。Through the analysis we found that the effect will become more obviously with the increase of thickness or width of superstratum and the decrease of the coefficient of foundation bed ; ( 3 ) anisotropy and nonlinear elastic f. e. m. model has been established and the effect of stress dispersion in compound two - layer foundation was analyzed on the base of the model. from the analysis we can conclude that the coefficient of subsidiary stress dispersion will amplify with the increase of thickness or width or stiffness of back - up coat ; ( 4 ) the formula which can be used in conventional calculation has been deduced for calculating the coefficient of subsidiary stress dispersion and it also has been affirmed to be reasonable through the checking calculation ; the whole theory of compound two - layer foundation has been brought forward in this paper and it ' ll enrich the theory of composite foundation
針對以上問題本文做了以下一些工作並得到若干結論: ( 1 )提出了「復合雙層地基」的概念,並通過工程實例證明此概念的提出有其合理性和必要性; ( 2 )用彈性地基梁理論證實了復合雙層地基確有應力擴散效應,且擴散效應隨上覆硬層厚度、剛度的增加而增大,隨下臥層基床系數的增大而減小; ( 3 )建立了非線彈性、各向異性有限元模型,並以此為基礎分析了復合雙層地基的應力擴散效應,得到附加應力系數隨加固層厚度、寬度、剛度的增加而增大的結論; ( 4 )推導了可用於常規計算的復合雙層地基應力擴散系數公式,並代入工程實例進行了驗證。Breath or diversity of product lines
產品線的寬度或多樣性For example, if this property equals 1, the custom cap width is 10, the custom cap height is 5, and a line is drawn with a pen with a width of 3, then the cap is drawn 30 units wide and 15 units high
例如,如果該屬性等於1 ,自定義線帽寬度為10 ,自定義線帽高度為5 ,並且用寬度為3的鋼筆繪制直線,則所繪制的線帽有30個單位寬、 15個單位高。Provided that the height of collar stand remains constant, the lapel ease and gradient data of lapel collar increase with the increase of the collar width, but in the case of increment, the former almost keeps linear increase tendency, whereas the latter exhibits a progressive decrease
假定領座高度不變,隨著領面寬度的增加,翻領松量的變化呈線性增加,且增量基本保持不變;而倒伏量也隨翻領寬度的增加而增加,但增幅呈遞減趨勢。On the base of above it, this paper discuss the synthesis of optimum distributed arrays by nonuniform spacing in the sense of dolph - chebyshev. having derived the equations of optimum element distribution, we analyze the exponentially spaced array, which are optimum when the elements are isotropic and equally weighted, and the array by general raised cosine function. the formulate for estimating the sidelobe envelope, beamwidth of the array pattern and clean region width are obtained
推導了最佳陣元分佈方程,分別對陣元無方向性和等加權時的最佳分散式陣列? ?指數間隔陣列和採用廣義升餘弦加權的最佳分散式陣列進行了分析,推導了天線方向圖旁瓣包絡、波束寬度,干凈掃描區寬度的估計公式,給出了近軸旁瓣電平與陣列參數的關系。This processing line is composed of two sszym 1500a straight line double pencil edgers, with 90transfer worktable. which adopts plc control system sets processing parameters via interface to control width and speed, double screw rod and double straight line glide transmission, guarantee the active briges parallel moving precision, can grind 3 8mm thickness flat edge and pencil edge. this machine structure was designed tightly, function stabilized with high efficiency. it is mainly suit for large batch industrial glass which does deep process and production, be matched with glue printing steel etc. production line. this product is a master work with firenew design by our company, it is another contributisn for chinese glass double edger series
採用plc控制系統通過界面設定參數,控制加工的寬度和速度,雙絲桿和雙直線導軌傳動,保證活動橋的平行移動精度,適用與加工3 8mm的小規格玻璃的平邊和圓邊。該機設計結構緊湊,性能穩定可靠,生產效率高。主要適應大批量工業玻璃深加工生產可以與夾膠印花鋼化等生產線配套使用。The advantages of simple structure, good linearity, no magnetic saturation, widely measure band make it fit sample in optical - electric current transformer nicely. while, there also have many new problems in applying rogowski coils
Rogowski線圈不僅具有結構簡單、線性度良好、無磁飽和、測量頻帶寬、動態范圍大等優點,而且體積小、重量輕,非常適合混合式光電電流互感器的取信號采樣繞組用。In this paper, some characteristics of flow movement and sediment transport are analyzed by using the flume experiment data. the cross section of compound channel can be divided into four regions : the undisturbed region in main channel, the interactive region between channel and plain, the undisturbed region in flood plain and the boundary region. in the undisturbed regions, the distribution of longitudinal velocity along the depth has the feature of lograithmic. whereas, in the interactive region, the longitudinal velocity does not obey the logarithmic distribution law, but it can expressed as a revised logarithmic function by using a wake function. on the basis of the kinematic equation the velocity distribution of transverse velocity is obtained. in the boundary region, the longitudinal velocity obeys the law of parabolic distribution. furthermore, according to the simplified diffusion equation, the transverse distribution of sediment concentration in the interactive region is deduced. the analysis is in good agreement with the measured data
本文根據漫灘水流的運動特點,將漫灘水流的復式斷面分為主槽平衡區、灘槽交互區、灘地平衡區及邊壁區等4個區,並給出了各區寬度的經驗公式.根據灘槽交互區垂線流速分佈的變化特點,提出了附加尾流函數的對數流速分佈公式.在簡化水流運動方程和泥沙擴散方程的基礎上,對灘槽交互區內垂線平均流速及含沙量沿橫向分佈進行了理論分析,提出了反映灘槽水流動量交換強度的橫向渦量粘性系數及橫向擴散系數的表達式,得到了漫灘水流垂線平均流速及含沙量沿橫向分佈的解析解,並與實測資料吻合較好Based on the research of several shiplocks, the temperature and stress field of the lock floor is simulated under temperature and gravity loads, where the shiplock floor is built on different foundations, the effect of setting up wide construction joints is analyzed by the nonlinear finite element method
作者通過對多個船閘工程的研究,結合非線性有限元模擬分析方法,考慮重力、溫度等荷載,計算分析土基和巖基上船閘結構底板預留寬縫施工方法的效果。The result of our experiment indicated the novel biosensors exhibite excellent electrochemical characteristics to glucose with substantial improvement in sensitivity, low detection limit, stability and anti - interferer
實驗證明,引入了新的電子媒介體后,該傳感器的靈敏度顯著提高,線性范圍顯著加寬,能有效的消除抗壞血酸和尿酸等的干擾。In order to make the sensitivity of 2 - demension accelerometer along the two main arbors almost identical, symmetric four - beam structure that embeds a double - sides interdigitated differential capacitive with puckered beam in two directions was used as sensitive component. in addition, the differential capacitive accelerometer fabricated by bulky silicon micromechanical technique has high sensitivity, wide measurement scope, less nonlinear error, and simple converting circuit. then, the structure parameters of the sensitive component were calculated and stimulated, which results in a set of the optimized structure design parameters, main fabrication procedure and several key fabrication technology
為使二維振動傳感器在兩主軸方向的靈敏度大致相同,敏感元件採用高度對稱的四梁結構,其中每個軸向上均採用帶折疊梁的雙側叉指電容結構,採用體硅微機械工藝製作的高深寬比叉指電容式敏感元件,具有高靈敏度、寬量程、非線性誤差小、外圍電路簡單等優點;對設計的敏感元件結構參數進行了計算,並利用有限元法進行了模擬分析,根據模擬結果得出了優化參數;在確定敏感結構的基礎上,研究了敏感元件採用體硅微機械加工工藝製作的工藝流程和關鍵工藝技術;對敏感晶元內部的c - v介面電路進行了原理設計與分析,利用差動測量技術得到由振動引起的微小電容變化量,經c - v介面電路進行相位調制處理,然後通過解調輸出與加速度成正比的電壓信號。Considering the fact that the analog system is not so good as the digital system on the respect of variation of bandwidths and on the respect of switch between different bandwidths. this paper proposes to adopt the dds ( direct digital synthesis ) technique that produces chirp signals of different bandwidths to improve the situation of losing tracks for the ocean satellite altitude indicator in measuring coarse surfaces
現在的雷達基本上採用模擬系統產生線性調頻信號,由於模擬系統在帶寬變化方面和不同帶寬間切換方面不如數字系統,本文採用dds ( directdigitalsynthesis )技術產生不同帶寬的線性調頻信號以改善海洋衛星高度計在測量粗糙表面時存在的失鎖現象。Generally speaking, the regularity of orthonormal wavelet bases with compact support increases linearly with the support width. but if we relax the orthogonality, much more freedom on the choice of wavelet function is gained
一般來說,對于規范正交小波基,它的正則性階數是隨其支集寬度線性增長的,而如果放鬆了正交性要求后,母小波可以同時具備局部支撐性和無限光滑性。The form of variable cross - section, used mostly in the practical projects, just has the change of the linear variation on the height of the web plate while keep the width of the flange c hangeless
實際工程中使用最多的變截面構件形式是僅構件腹板高度線性變化,翼緣寬度保持不變的形式。This article, aiming at the specialties of rmb currency image, puts forward a new method using linear transform of image gray to diminish the influence of the background image noises in order to give prominence to edge information of the image. then the edge characteristic information image is obtained by edge detecting using simple statistics. by dividing the edge characteristic information image in the width direction into different areas, getting the number of the edge characteristic points of different areas as input vectors to random masks and optimized by ga
文中提出了利用圖像灰度線性變換來抑制背景圖案噪聲的影響,突出圖像邊緣信息;然後採用簡單統計法進行邊緣檢測,得到邊緣特徵信息圖;最後通過對邊緣特徵信息圖在寬度方向上進行均勻劃分成不同的區域,統計不同區域的邊緣特徵點的數目作為神經網路的初始輸入向量,對初始輸入向量用隨機掩碼處理和遺傳演算法進行優化得到最終輸入向量,通過三層bp神經網路分類器進行分類,達到了人民幣識別的目的。Properties. to set color, style, and width properties of the line, you must use the properties window in visual studio
若要設置線條的顏色、樣式和寬度屬性,則必須使用visual studio中的「屬性」窗口。One new method that the uwb signal can be received ambiguously has been presented in this dissertation. furthermore, the sampling lfm signal becomes two sine signals with different frequencies based on two different delay processes. based on fft and remainder algorithm, the modulation rate and initial frequency of sub - sampling lfm signal are estimated precisely and unambiguously in negative snr
該方法通過在數字域對信號進行兩路不同的延時和余數定理實現欠采樣條件下超寬帶線性調頻信號的調制斜率和初始頻率的無模糊估計,在不降低參數估計精度的前提下,解決了欠采樣方法引起硬體復雜度增加的問題。分享友人