寸進尺退 的英文怎麼說
中文拼音 [cùnjìnchǐtuì]
寸進尺退
英文
advance by inch and retreat by foot-
From less to more, i worked him up to considerable irritation ; then, after he had retired, in dudgeon, quite to the other end of the room, i got up, and saying, i wish you good - night, sir, in my natural and wonted respectful manner, i slipped out by the side - door and got away
我得寸進尺，惹得他很惱火，隨后趁他怒悻悻地退到屋子另一頭的時候，站起來象往常那樣自自然然恭恭敬敬地說了聲「祝你晚安，先生， 」便溜出邊門走掉了。Evil comes to us by ells and goes away by inches
罪惡來時，尺進寸退The quality of machine with loading and unloading bushing has been improved and the structure of which has been turned rationalization ; fourthly, according to the relation of the tight fitting between resist grind bushing and suspension yoke, making use of the two simple thick circles theory in the elastic - plastic mechanics and the fourth strength theory, it integrated theory with it ' s formulation characteristic and developed the solver of the tight fitting force in the system of c + + builder. it could realize the solve of all tight fit force and save up the frame ' s size and the tight fitting ' s data in database in order to use in the future ? the assemble force of tight fitting can be used as the rule of estimating loose or tight bushing in theory
3 ） 、利用了ansys8 . 0自帶的opt （優化技術）對c型夾具進行了結構上的優化，實現了一定強度和剛度的條件下， c型夾具的質量最小，使裝、退套機的質量得到了改善，結構更趨于合理化； 4 ） 、根據合金套和吊耳的過盈配合關系，應用彈塑性力學中的兩個簡單厚臂圓筒理論及第四強度理論，結合軸套裝配方案特性，在c + + builder平臺上開發出了過盈配合裝配力的求解器，它能求解出所有過盈配合所需裝配力，並將各種配合尺寸和過盈量的數據庫存化，以便將來調用。Prepared technical parameters were optimized by l9 ( 34 ) experiment analysis. a unique method for cleaning and drying of substrate - cleaning used by scour, drying used by infrared light was fished out by large numbers of experiment. chemical mechnism of zno thin film prepared by sol - gel technique was discussed by dta for the first time. by the measurements of sem, xrd and uvs, the thin film was analysed. the result proved that the thin film with strongly preferred orientation of c - axis perpendicular to the substrate surface which surface was homogenous, dense and crackfree was the crystalline phase of hexagonal wurtzite. the thin film was composed of plentiful asteroidal crystal which crystal dimension approximately 10 30nm. the average transmittance of thin film in visible region was above 90 %. the results of measurements else also proved that the thickness of single dip - coating was 75 240nm, this films resistivity was found to be 3. 105 102 3. 96 105 ? cm. the thickness and resistivity of thin film influenced by dope - content, withdrawal speed, pre - heat - treatment, anealing were reseached respectively
利用xrd 、 sem以及uvs光譜儀等分析方法對薄膜進行了研究，結果顯示，所制備的薄膜為六方纖鋅礦型結構，具有高c軸擇優取向性；表面均勻、緻密，薄膜材料由許多星狀晶粒組成，晶粒尺寸大約為10 - 30nm左右；薄膜可見光透過率平均可達90 % ；對薄膜厚度以及電學性能進行了測定后發現：單次鍍膜厚度約為75 - 240nm ， al ~ （ 3 + ）離子摻雜型氧化鋅薄膜的電阻率在3 . 015 102 - 3 . 96 103 ? cm范圍內；分別研究了摻雜濃度、提拉速度、預燒溫度、退火溫度等工藝參數對薄膜厚度和電阻率的影響。We consider that the complexes of bmon ( m, n > 1 ) or the point defects induced by heavily boron doping may be involved in the nucleation of oxygen precipitates at high temperature range of crystal cooling. therefore it is reasonably deduced that the density of voids in hb cz silicon increases and the size of voids decreases due to the reduction of vacancy concentration as a result of heavy boron - doping enhanced oxygen precipitation prior to the void formation
在實驗事實的基礎上，我們認為在重摻硼硅單晶生長過程中， bmon （ m ， n 1 ）復合體或摻b引起的點缺陷能在晶體冷卻過程中的較高溫度階段形成，且在隨后的退火過程中能穩定存在，作為氧沉澱形核的核心，從而促進了氧沉澱，減小了大直徑硅單晶中void缺陷的尺寸，增加其密度。In the making process we use hot - forging warm - forging cold extrusion forming and magnetic annealing processes to completely solve the problem of complex form hign precision dimensions difficult manufacturing lower power and so on. what s more, part surface is very smooth with no trimmed margin, continuous flowing metal fiber, high strength, lower noise. forged claw poles obviously increase generator s power and life, and also improve finished product rate of roughness
在製造過程中採用了熱鍛溫鍛冷擠壓成型及磁性退火等先進生產工藝徹底解決了精鍛「爪極」形狀復雜尺寸精度高製造難度大功率低等問題，且產品表面光潔無飛邊金屬流動纖維連續毛坯強度大噪音低，明顯提高了發電機的功率和壽命，並且提高了毛坯成品率。分享友人