峰值光強度 的英文怎麼說

中文拼音 [fēngzhíguāngqiángdù]
峰值光強度 英文
peak light intensity
  • 峰 : Ⅰ名詞1. （山的突出的尖頂） peak; summit 2. （形狀像山峰的事物） peak-like thing Ⅱ量詞（用於駱駝）
  • 光 : Ⅰ名詞1 （照耀在物體上、使人能看見物體的一種物質） light; ray 2 （景物） scenery 3 （光彩; 榮譽） ...
  • 強 : 強形容詞（強硬不屈;固執） stubborn; unyielding
  • 度 : 度動詞[書面語] （推測; 估計） surmise; estimate
  1. The peak of temperature is more high with metal powder, as a result of absorptivity is more high

    添加金屬粉末時，材料表面對激光的吸收率增強，同一測量點的峰值溫度升高。
  2. E., the carrier frequency of a gaussian beam deviates from the resonant frequency of a fabry - perot etalon ), variations of the peak intensity, the position of the peak intensity and the dwdm systems, has received considerable attention. in this work, after taking into account the wavelength - depended reflectivity distribution profile of a fiber bragg grating, the oscillation wavelength # _ ( 1 ) of long external cavity fiber bragg grat

    與共振情況（即高斯光束的載波頻率與法布里一拍羅濾波器的諧振頻率一致）相比，非共振條件（即高斯光束的載波頻率與法布里一拍羅濾波器的諧振頻率存在偏差）一透射光束的峰值強度、峰值強度所對應的位置、以及光斑的大小隨入射角的變化都發生了顯著的改變。
  3. Peak of luminous intensity luminous flux

    發光強度光通量峰值
  4. The reason to cause this phenomenon is due to the change of electric field in the blue oled to induce the probality of the carrier shifted and the hole - electron recombination zone changed, which was a possible alternative to achieve color display. 3 ) device with the structure of ito / npb / adn : balq3 / alq3 / mg : ag was fabricated. when the balq3 dopant concentration was about 25 mol %, a high performance devcie with luminous efficiency of 1. 0 lm / w, the peak of emission spectrum at 440 nm, the cie coordinate at ( 0. 18, 0. 15 ), and half lifetime of unencapsulated device about 950 hrs was achieved

    導致本現象的原因是由於各有機層電場強度的變化影響了空穴和電子的隧穿幾率，從而導致載流子的復合區域發生改變而發出不同顏色的光; 3 ）制備了結構為ito / npb / adn : balq3 / alq3 / mg : ag的藍光oled ，空穴阻擋材料balq3的摻入顯著影響了oled的光電性能，當balq3的摻雜濃度為25mol %時， oled的發光效率為1 . 0lm / w ，發光光譜的峰值為440nm ，色純度為（ 0 . 18 ， 0 . 15 ） ，未封裝器件的半衰期達到了950小時; 4 ）在藍光材料adn中摻雜npb 、 balq3和tbp三種材料時，不僅改善了器件的發光亮度和色純度，而且提高了器件的發光效率和壽命。
  5. Was added, the absorption of morin at 350nm decreased and a new absorption peak at 419nm appeared. adding of nucleic acids to the morin - al binary system leads to decrease of the absorption at 350nm and great increase at 419nm. there is an isochromatic point at 370nm. the increase of absorbance at 419nm is proportional to the amount of nucleic acids added within certain concentration range. based on this, a new sensitive nucleic acids analysis method is established. the linear ranges of ct dna, fs dna and y rna are 0. 7135. 4 0. 6425. 6 and 0. 9428. 4g ml, respectively

    鋁離子的加入使桑色素350nm處的吸收峰下降，在419nm處出現桑色素-鋁絡合物的吸收峰。再往桑色素-鋁離子二元體系中加入核糖核酸或脫氧核糖核酸，則進一步引起桑色素350nm吸收峰的降低， 419nm處的吸收大大加強，同時在370nm處有一等色點。 419nm處吸光度的增加值與加入的核酸量在一定范圍內成正比，基於此建立了在較寬范圍內測定核酸的方法。
  6. Effect of spherical particles relative refractive index on the most peak value of scattered light field intensity

    球形粒子相對折射率對散射光場強度最大峰值分佈的影響
  7. P - n, n - dimethlaminobenzates ( ( ch3 ) 2nc6h4coor ) have typical ict characteristics. the ct emission and the fluorescence intensity ratio of ct band to normal band ( ict / ile ) were different in organic solvent and in the aqueous solvent with ctab micelle when the length of r group was increasing

    N ， n -二氨基苯甲酸酯系列具有典型的雙熒光，從甲酯到辛酯隨著酯烷基鏈的增長，它們在有機溶劑和膠束水溶液中的熒光峰位置以及雙重熒光強度之間的比值不同。
  8. Based on the theoretical analysis and experimental researches, it is presented that the wider spectra are resulted from the many fluorophores with large numbers of vibrational energy levels on the ground level in the blood cells, and the reduction of the spectral intensity is due to the reabsorption of the blood cells and the energy transfer of the collisions between the fluorophore and another one or other macromolecule. on the other hand, when the concentration of the blood cells is increased, the reabsorption of the blood cells, the secondary fluorescence due to the reabsorption and the influence of the concentration on the energy levels of fluorophores are all the factors of the red - shifted spectral peaks

    在進行理論分析和研究的基礎上，提出了因血細胞中存在多種熒光團，且這些熒光團的電子能級上又存在大量的不同的振動能級，從而導致被激發的熒光團發出較寬的熒光光譜；血細胞濃度的增大，熒光團以及其他大分子之間的距離變小，造成它們之間因碰撞的能量轉移概率加大，因而易產生熒光猝滅，結果導致熒光強度的變小；血細胞溶液中重吸收所導致的熒光猝滅和二次熒光發射，以及血細胞濃度的變化對其中熒光團能級系統的影響都是導致熒光峰值波長「紅移」的原因；進而研究了led光誘導血細胞產生熒光光譜的機理。
  9. In general, the lens chromatic aberration and the group velocity dispersion lead to a broadening in the temporal and spatial intensity distributions at the focal plane and a decrease o

    一般說來，透鏡色差和群速度色散會使焦平面上脈沖光束的時間、空間光強分佈展寬，峰值光強降低。
  10. The method permits the calculation of the three stages of shock wave evolution, and gives the temporal and spatial relationship of peak pressure, velocity, and profile of shock wave

    文中採用流體動力學模型，解析地描述了脈沖強激光輻照靶材時，激波的產生及增強、維持和衰減規律，給出了激波峰值壓力、激波速度、激波波形的時空關系。
  11. Peg and superfluous aa reaction by complete concatenation method, the esterify production " esterify water " and acid number were mensurated, it shows that the esterify reaction would be processed under 100 esterify temperature and with amine accelerantthe tide of esterify reaction was substantiated by ir. in the ir spectrum, the characteristic peak of hydroxy of peg and carboxyl of aa were weakened. and the ester link of peg was reinforce. the " esterify water " was increased gradually and the acid number of esterify production was debased gradually along with the extent of esterify time and the augmentation of molecular weight of peg

    通過聚乙二醇與過量的丙烯酸採用全連續法進行反應，測定酯化產物「酯化水」和酸值等宏觀手段反映出在胺類促進劑、 100的酯化溫度等條件下的酯化進程，而利用紅外光譜（ ir ）分析所反映的聚乙二醇的羥基和丙烯酸的羧基特徵峰減弱，而pea的酯基特徵峰加強等特徵進一步證實了宏觀手段所表現出來的酯化趨勢：隨著酯化時間的延長和聚乙二醇分子量的增大，產生的「酯化水」逐漸增加，酯化產物的酸值逐漸降低；從酯化時間看，當反應時間達到300min時，酯化物的酸值達到最小，而從ir分析來看，酯化物pea4的羥基峰在300min時減弱到最小， pea23在120min時羥基峰的表現出酯化基本完全。
  12. It preliminarily establishes a set of test theory and technical approach to wind tunnel test. specifically speaking, it includes following work : ( 1 ) theoretical analyses on key parameters of ao effect were made. from maxwell equation, the computation formula for focusing intensity of ordered disturbance and the computation formula for pulse peak intensity were derived

    初步建立起了一套氣動光學風洞測試試驗的理論和技術，完成的主要研究工作有: （ 1 ）從理論上進行了氣動光學主要參數的分析，從麥克斯韋方程出發，推導了有序擾動的聚焦強度的計算公式及脈沖峰值強度計算公式。
  13. Presently, the laser pulse from the high power ultrashort laser system is several femtoseconds in duration, tw ( or pw ) level in peak power, 1020 w / cm2 ( or 1021 w / cm2 ) in focusing power density, according electric field is much stronger than coulomb field in atoms

    目前，高功率超短脈沖激光放大系統輸出的激光，脈寬達到幾個飛秒，峰值功率達到太瓦甚至拍瓦量級，聚焦功率密度達10 ~ 20w cm ~ 2 ，甚至1021w cm2 ，相應的電場比原子內庫侖場強得多。
  14. The photoluminescence of the thin films without post heating is weak. only one luminescence band is found nearby 473nm. two luminescence bands are found after post heating, nearby 493nm and 368nm respectively. the intensity of the luminescence bands increase little by little when the temperature and the time of post heating continues to increase

    而退火處理過后，薄膜出現兩種光致發光現象，即藍色發光和紫外發光，其峰值分別在493nm和368nm附近，而且隨著退火溫度的升高和退火時間的延長，發光譜帶的強度逐漸增大，峰形的位置也有不明顯的藍移。
  15. Theoretical analysis shows : compared with oled, moled with alq3 as light - emitting layer can emit different wavelength light by modulating length of cavity, spectral full width at half - maximum of moled changes from 100nm to 10nm ~ 20nm and the light intensity at peak is increased by about 20 times, and luminous efficiency can be enhanced

    理論分析表明：通過調節腔長，用alq3作發光層的moled可以發出不同中心波長的光，譜線寬度由oled的約100nm變為10 ~ 20nm ，峰值光強提高20倍左右，總發光效率也有所提高。
  16. In this work, incident super - gaussian pulse propagation in conventional single - mode fibers has been investigated in detail after taking into account the fiber chromatic dispersion. the results show that for an incident super - gaussian pulse with steep leading and trailing edges, its shape undergoes a variation from near - rectangular, two - peak, and finally to single - peak. in the meantime, its peak intensity increases at first, after passing a maximum, and finally decreases monotonously

    數值模擬的結果表明:超高斯入射光脈沖在光纖中傳輸時脈沖波形、瞬時惆啾、以及峰值強度的演變規律與高斯入射脈沖不同，脈沖波形不再總保持單峰結構，通常將經歷一個從近平頂、多峰、最後到單峰的演變過程;從脈沖的前沿到后沿，瞬時明啾也不再為線性，而是具有多個極值;峰值強度隨傳輸距離的變化趨勢也不再為一單調遞減，而是先增加后減小。
  17. The results show that the peak intensity of the transmitted beam decreases with the increase of the input angle, the position of the peak intensity of the transmitted beam is shifted, and the spot size of the transmitted beam is changed. under the nonresonant case ( i

    結果表明，當以較大角度入射時，輸出為一系列空間分離的光斑:當以較小角度入射時，輸出盡管為單一光斑，但是與輸入相比，其峰值強度位置發生了偏移， _且光斑變大。
  18. Led light - induced fluorescence spectra of whole blood, erythrocyte and hemoglobin are obtained in the case of different concentration of blood cells solution with various excitation wavelengths. the intensity and peaks of the spectra from 430nm to 700nm depend strongly on the concentration of blood cells

    通過改變激發光波長和血細胞濃度，獲得了led光誘導全血、紅細胞和血紅蛋白產生的熒光光譜，其光譜覆蓋了430 700nm波段，且光譜強度和峰值位置均與溶液濃度有較強的依賴關系。
  19. The angle ( in the plane through the beam axis ) over which the luminous intensity drops to a stated percentage of its peak intensity

    在光束的軸面上，光強值降至其峰值某一比例時所對應的角度。
  20. The oxidizing parameters of the anodization in the following experiments were preferred on the basis of measuring the dependence of pl properties ( peak position, and max intensity, etc. ) on anodization conditions, such as the anodizing current density, the time of the anodization, the concentration of the solution ( mainly of hf ), and on the doping level of the substrate

    刻蝕時間、刻蝕液配比及襯底電阻率對pl發光強度、峰值波長等性質的影響。在此基礎上優化出制備多孔硅的具體參數。對不摻sb與摻sb的snci 。
分享友人
分享到 Line

分享到臉書