工作油缸 的英文怎麼說
中文拼音 [gōngzuòyóugāng]
工作油缸
英文
operating cylinder-
In the course of working, ， the plow will make use of the shuttling method so that it can dig alternately either on the left or on the right. compared to the unilateral plow, it can improve the productivity because it can help leave off the soil 、 take from the consumed energy and reduce the empty journey. to meet the requests above, we will use a remote cylinder with both a small cubage and double functions, approximately designing the plow to be columniform and symmetric. after the experiment for a period in the field, we found that the most frayed areas had happened at the places of both plow shank and share and at the same time the base of the remote cylinder had ruptured suddenly
與單向犁相比，其優點在於：耕地無開、閉壟，地表平整，降低了耕后整地的能量消耗，減少了地頭的空行程，因而大大提高班次生產率。為了滿足犁體梭式作業的要求，我們採用了一隻小容積雙作用的液壓油缸；同時對犁壁曲面的形狀採用了近似圓柱形的對稱設計。但經過一段時間的田間試驗，我們發現：該犁犁胸部分的犁脛和犁鏵上的犁尖在工作中磨損較為嚴重；主犁梁和油缸缸體的連接部分（即油缸底座）突然發生了斷裂，造成整個犁體無法正常工作。Carry out underground and above ground ido tanks cleaning and leakage inspection for clp power in castle peak power station in 2006
2006年于中電青山發電廠進行地底、地面油缸清理及壓力測試工作。Ssc suzuki saving control system
鈴木節油控制系統可變工作缸數發動機Through consulting lots of relevant references, present research of direct drive volume control hydraulic servo system is summarized in this paper, the principle and character of this system are expatiated, the principle of vector control is introduced. at the same time, the mathematical model of ac asynchronous motor is set up based on the vector control theory. the mathematical models of both the pump controlled motor and pump controlled cylinder are set up and simulated in this paper
在查閱大量國內外相關文獻的基礎上，本文綜述了國內外對該系統研究概況，闡述了該類系統原理和特點;闡述了矢量控制的基本原理，並基於這一原理建立交流異步電動機的數學模型;分別建立了泵控馬達系統和泵控缸系統的數學模型，並給出了模擬分析;設計了用於泵控馬達系統的集成閥塊，加工了密閉壓力油罐;針對現有直驅式電液伺服裝置所存在的問題，本文主要針對系統工作過程中所產生的噪音與爬行問題進行了一定的研究。In the light of the problems of the air balance system of model lcj1250 chain drive pumping unit, it is proposed to change the air balance with counterweight balance, and three criteria for the modification is put forward : ( 1 ) ensuring the reliability of the unit with smooth operation, low noise and long life ; ( 2 ) cutting down the production cost and using less component parts as possible ; ( 3 ) carrying out modification without such main technical parameters as stroke, pumping speed and maximum polished rod load
針對lcj1250氣平衡式鏈條抽油機存在氣平衡故障率高和現場維修困難等問題，提出將氣平衡改造成工作可靠的重力平衡的方案，並確定了改造的三個原則：一是保證整機的可靠性，使抽油機運轉平穩，振動噪音小，壽命長；二是力求降低生產成本，減少零部件製造，盡可能選用原來的通用件，捨去平衡缸和空氣包等氣平衡附件，在原往返架主體上懸掛一個配重箱；三是力求不改變沖程、沖次及最大懸點載荷等主要技術參數。Abstract : in the light of the problems of the air balance system of model lcj1250 chain drive pumping unit, it is proposed to change the air balance with counterweight balance, and three criteria for the modification is put forward : ( 1 ) ensuring the reliability of the unit with smooth operation, low noise and long life ; ( 2 ) cutting down the production cost and using less component parts as possible ; ( 3 ) carrying out modification without such main technical parameters as stroke, pumping speed and maximum polished rod load
文摘:針對lcj1250氣平衡式鏈條抽油機存在氣平衡故障率高和現場維修困難等問題，提出將氣平衡改造成工作可靠的重力平衡的方案，並確定了改造的三個原則：一是保證整機的可靠性，使抽油機運轉平穩，振動噪音小，壽命長；二是力求降低生產成本，減少零部件製造，盡可能選用原來的通用件，捨去平衡缸和空氣包等氣平衡附件，在原往返架主體上懸掛一個配重箱；三是力求不改變沖程、沖次及最大懸點載荷等主要技術參數。Carry out international grit blasting, bottom plate repairing and repainting work for aboveground oil tank no. 8 in chevron tsing yi terminal in 2006
2006年于雪佛龍青衣油庫進行8號油缸缸內打沙、修補缸式底及噴油工作。Based on the theoretical analysis and design practice in successful development of allway desiel engine in china, the design concepts of key parts and components of engine, in particular the cylinder block and cylinder head, are analyzed for meeting the requirements for high performance and low emission as well as normal and reliable operation of diesel engine for medium and heavy commercial vehicle under high combustion pressure and high thermal load
摘要結合我國自主開發的「奧威」發動機在設計工作中的理論分析與實踐，就低排放中重型商用車柴油機在開發工作中為滿足高性能、低排放的要求及在高燃燒爆發壓力和高熱負荷下正常可靠地工作，對發動機的關鍵零部件，尤其是缸蓋與缸體的設計概念進行了分析。( 4 ) in order to improve the system and its working function, a hydraulic controlled direction valve is connected in the main oil circuit to control the differential of the piston. then the dimentions of the cylinder and the piston are reduced, improving the working properties
廣東工業人學工學顧十學位論義（ 4 ）為進一步改進設計方案，提高其工作性能，在主油路中加一液動換向閥，控制活塞的差動，從而將減小油缸和活塞的尺寸，提高工作性能。Leaving the rated load, especially with low load and free running operation, ihe efficiency of turbocharger and ratio boost pressure decrease, leading to the shortage of air in cylinders and worsening of combustion, and the economic, power and exhaust performances deteriorate
當偏離標定點，尤其在低負荷和空轉工況工作時，增壓器效率降低，增壓壓力明顯下降，導致氣缸供氣不足，缸內燃燒不良，柴油機的經濟性能、動力性能和排放性能將嚴重惡化。The engineering drilling machine of kp2200 type is double layers bottom plate, and drives through hydraulic pressure, upper plate can move fore and aft on the lower plate, the drill power leans back under the action of oil cylinder, the lower plate can put the drilling tool within 2. 5 meters into well hole without moving, it is convenient and reliable, and ensures construction quality
Kp2200型工程鉆機為雙層底盤，通過液壓驅動，上盤可在下盤上前後移動，鉆塔在油缸的作用下後仰，下盤不動即可把2 . 2米以內的鉆具放入井孔內，方便可靠，保證施工質量。A method based on the application of an injection process analysis software is introduced in this article, which optimize injection process through changing the design of fuel - injection pump cam. a model of 1115 single cylinder direct injection diesel engine is used as an example. with the help of pre - journey optimization, increasing cam lift and using tangent - function can make the matching of the injection system with the diesel more reasonable. without changing fuel pump installing size, it can enhance injection rate and injection pressure and improve the diesel operating stability in low speed condition
本文以國產1115型單缸直噴柴油機為例，介紹一種應用噴油過程分析軟體改進噴油泵凸輪設計的方法，通過增大噴油泵凸輪升程、採用切線函數凸輪並優化預行程的方式，在不改變噴油泵安裝尺寸的前提下，可提高噴油壓力和噴油速率，改善柴油機低速工作穩定性，使噴油系統與柴油機匹配更合理。It is important to maintain the ship chamber horizontal and keep cable tensions in equilibrium during the running of the hoisting fully balancing type ship lifter. the distributions of displacements and cable tensions are unbalanced because of construction errors. a hydraulic balance system which has 48 oil cylinders is designed to eliminate the unsafe factor
為了消除該不安全因素，使升船機工作時，承船廂能在水平、受力均衡的狀態下升降，設計中的升船機有一個由48個液壓油缸組成的液壓均衡系統，靠它維持船廂的水平狀態和提升索拉力均衡。According to the principle of curve axial symmetry, authors inferred the theoretical foundation of error - free translation of the working equipment of loader and proved that when the diameter of piston rod on arm oil cylinder was designed properly, the two oil cylinders could be guaranteed to have a synchronous movement which made the bucket maintain translation throughout the working process under the condition of the oil cylinder ' s basic parameter ; also made the equipment structure of the loader greatly simplified and provided the reference for improvement of the present equipment of loader
根據曲線軸對稱原理，推導出了能使裝載機工作裝置無誤差平移的理論基礎，證明了只要適當地設計動臂油缸活塞桿直徑，就可以在油缸的基本參數上保證機構工作時兩油缸同步運動，使鏟斗在作業過程中保持平移；使裝載機工作裝置結構大為簡化，為進一步改進現有裝載機工作裝置提供參考。Wuxi nakano machinery co., ltd. and japan - field technology, the development of a new type of closed turntable polishing concrete slabs. polished tiles from the radically changed the cooling water production accelerated, workers unable to operate close to the phenomenon ; supported by tanks under the workpiece table, it will not only compensate for the loss millstone, but stable grinding force. different uniform surface quality products ; with the grinding process workpiece turntable and rotating products
無錫中野機械有限公司引進日本技術，全新開發的轉臺型封閉式混凝土地磚磨光機，從根本上改變了磨光地磚生產中冷卻水飛濺，操作工人無法靠近的現象工件轉臺由下油缸支承，不僅能及時補償磨石的損耗，而且磨削力穩定不變，不同產品的表面質量均勻一致磨削過程中產品隨著工件轉臺而轉動，避免了其它型式磨光地磚生產中產品不動而帶來的同一產品表面質量不均的現象。The characters of sdy oscillationing oil cylinder type hydraulic steering gear are : the construction is simple and reasonable, operation is flexible and steady, maintenance is convenient and leaktightening. we also assemble two suits control devices ( hand steering gear and emergency steering gear ) and oil pump series, the function of which is safe and reliable
200擺缸式液壓舵機具有結構簡單合理，操作靈活、工作平穩、安裝維護便捷和無泄漏等特點，並備用兩套操縱裝置（手操舵和應急操舵）及油泵，性能安全可靠。The extremely harsh working conditions directly result in high thermal and mechanical loads in diesel engines " piston assemblies, and so due to high stress it becomes one of the most vulnerable components assembly in diesel engine. piston assemblies " failures such as cylinder sticking, scoring, gumming, etc., greatly limit diesel engines " durability and reliability
由於長期工作在惡劣的環境下，柴油機活塞組要承受很高的熱負荷和機械負荷，這些負荷所產生的高綜合應力影響了它的使用壽命，其可能導致的咬缸、拉缸、結焦等故障極大地危害了柴油機整機的耐久性和可靠性。This machine is adopted advanced electrom - agnetism clutch turning, hydraulic stereotype perss with high speeding, pressure - strangthened oil vat and working tadle with air cushion. detecting instrument with direction
本機採用了先進的電磁離合裝置傳動，液壓壓紙採用了快速增壓油缸，壓力大，工作臺裝有氣墊。The new unit has following technical features : ( 1 ) the unit ' s load is balanced by means of the accumulator and hydraulic cylinder with special structure ; ( 2 ) the installed power of the unit can be reduced greatly by adopting the accumulator ; ( 3 ) variable frequency speed regulation ensures good energy saving effect, and the closed oil circuit requires less hydraulic oil ; ( 4 ) a bi - directional hydraulic lock in the oil circuit ensures the stability and safety of the operation of the pumping unit
新型機具有4個技術特點： （ 1 ）由於活塞柱塞式液壓缸的特殊結構和液壓蓄能器的配合使用，在平衡抽油機大部分載荷時，不需另外增加配重，可減小抽油機體積、質量和佔地面積； （ 2 ）抽油機下沖程時，與活塞柱塞式液壓缸相連接的蓄能器吸收能量，上沖程時儲存在蓄能器中的能量補充載荷上行所需的能量，大幅度降低抽油機裝機功率； （ 3 ）利用變頻容積調速節能效率高，閉式油路節省液壓油，同時大大減小液壓泵站的體積； （ 4 ）在閉式油路中採用雙向液壓鎖可使抽油機的啟停更加平穩、迅速，其工作的穩定性和安全性更好。An insulating lift is presented to improve the insulation property between the gripper and ground of high voltage hot - line cleaning robot, and to decrease the initial cylinder ' s working - pressure of vertical lifting mechanism
摘要提出了一種絕緣升降平臺，用於提高高壓帶電清掃機器人帶電作業時的對地絕緣性能，同時降低機器人垂直升降機構驅動油缸的初始工作壓力。分享友人