彈座機構 的英文怎麼說
中文拼音 [dànzuòjīgòu]
彈座機構
英文
ejection seat mechanism-
The design undertaken mainly from the following aspects : 1, mechanism ddesign : included the base and the joints : 2, trasmission mechanism design : adopted a synchronous toothelike transmission bell ; 3, balance system design : adopted springs and a brake and a lay air cylinder ; 4, design parameter and verify alculation ; 5, established motion equation by d - h method ; 6, simulated the motion locus by matlab software ; 7 ^ mapping out the part drawing or asesembly drawing
本設計主要是從以下幾個方面入手： 1 、機構設計：包括底座和臂關節的設計； 2 、傳動機構設計：將驅動電機安裝在底座上，利用同步齒型帶、離合器傳遞手臂的動力；利用齒輪傳動帶動底座回轉； 3 、平衡系統設計：採用了彈簧平衡系統、電磁式制動器和單向延時氣缸； 4 、設計參數和校核計算； 5 、用d ? h法建立運動學方程； 6 、利用matlab軟體對手臂的運動空間進行模擬； 7 、利用autocad2000繪圖：包括零件圖和裝配圖。Because expansion valves are high precision processing components, factory in its internal adjustment of the body parts are processed in a state of complete thermostatic, the temperature of the gas filling kits are demanding more consistent not detect leaks, in the completion of the expansion valve assembly also undergo strict testing and fatigue resistance aging sampling, the construction expansion valves : 1 : indeed temperature temperature kits ; 2 : temperature gas or liquid filled with the expansion corrugated ; 3 : spherical valve seat ; 4 spherical valves ; 5 : spring ; 6 : overheating degrees adjustment screw spacer and screw ; 7 : internal and external ( h - type ) sealed pieces ; 8 : thrust poles and corrugated of spacer ; 9 : fati ; 10 : capillary, and so on
因為膨脹閥是屬于超高精密加工的零件，在工廠對其內部調整機構零件的加工都在恆溫狀態下完成，其中的感溫包的氣體充填更是要求嚴格一致不允許一絲泄漏，在完成裝配的膨脹閥還要經過嚴格的測試和耐疲勞老化抽檢，膨脹閥的構造： 1 ：感知溫度的感溫包； 2 ：感溫氣體或者液體充填膨脹波紋腔； 3 ：球型閥座； 4球型閥； 5 ：彈簧； 6 ：過熱度調整螺絲墊片和螺絲； 7 ：內部和外部（ h型）密封件； 8 ：推力桿和波紋腔墊片； 9 ：閥體； 10 ：毛細管等等。Spring - mounted injector base : apply cement onto insole evenly by following shoe bottom curve
彈性底座膠盤機構：膠盤底座具彈性，可依鞋底弧度形狀，均勻布膠于中底。Consulting about foreign study, the research showed that the speed of firing can be improved by modifying the machanism of the automatic, and at the same time two problems must be solved, one is that more mechanisms should act at the same time to reduce the time of the whole actions of automatic mechanisms, the other is that the time of each mechanism ' s action should be reduced. the time can be reduced by several ways. the first one is to reduce the mass of mechanism, the second one is to increase the force applied on the mechanism and reduce the resistance, the third one is to shorten the working distance, the fourth one is to give abstention and cushion to mechanism before action ends. this thesis includes the following topics : discussion of the theory of the automatic and shell - swing design, establish the kinematic and dynamic models of the main structures in automatic and perform the corresponding mechanical analysis, set up a compendious cyclical diagram for the automatic ; the computer simulation to the navy gun ' s firing parts
由現有艦炮自動機循環圖可知，制約射速提高的幾個因素是：後座、復進佔用的時間較長，約占總循環時間的三分之一；供彈機的動作單獨佔用循環時間，且較長；輸彈機的輸彈時間較長；各機構動作重疊少；參考國內外的研究情況，本文提出了在採用改進完善現有自動機機構來提高射速時，必須考慮以下兩點： （ 1 ） 、力求在同一時間內能使更多的機構參與工作，並處理好各動作之間的銜接（即介面技術） ，以便縮短整個自動機的動作循環時間。分享友人