慣性扭矩 的英文怎麼說

中文拼音 [guànxìngniǔjǔ]
慣性扭矩 英文
inertia torque
  • 慣 : Ⅰ動詞1 （習以為常 積久成性; 習慣） be used to; be in the habit of 2 （縱容; 放任） spoil; indulge...
  • 性 : Ⅰ名詞1 （性格） nature; character; disposition 2 （性能; 性質） property; quality 3 （性別） sex ...
  • 扭 : 動詞1 （掉轉; 轉動） turn round 2 （擰; 旋轉） twist; wrench 3 （擰傷） sprain; wrench 4 （走路時...
  • 矩 : 名詞1. （畫直角或正方形、矩形用的曲尺） carpenter's square; square2. （法度; 規則） rules; regulations 3. [物理學] moment
  • 慣性 : [力學] inertia; inertance; sluggishness; the force of inertia
  • 扭矩 : torsion; torque; twist; lay; moment of torque; moment of torsion
  1. As a result of the simplified torsion moment of inertia, integral stability coefficients based on the gb50017 code increase relatively 5 % or 0. 01 ~ 0. 04 absolutely, only for hn behind hn400 150, whose calculation length goes beyond the limit of 8 meters, taking account of any load condition and any yield - point

    Gb50017梁的整體穩定系數公式的誤差是由扭轉慣性矩的簡化造成。任何荷載情況和鋼號，規格大於hn400 150的hn型鋼，當計算長度大於8米時，整體穩定系數偏高約5 ，絕對偏高量在0 . 01 0 . 04范圍。
  2. Delay is obvious in large body because of its inertia, moment force, stress and gearing. transfer of electical cell increases the delay. this paper points out that the delay can be compensated by using the smith control algorithm. the result of computer emulation proved that a better quality is gained by using the algorithm on heavy nc machine

    大慣量物體，由於其慣性，加之傳動鏈長，所需的扭矩大，引起的應變大，加上電氣轉換元件的滯后，故滯後效應明顯.該文提出用史密斯控制演算法將滯后進行補償.計算機數字模擬結果說明，對大慣量有滯后的重型數控機床，應用該演算法能得到較好的控製品質
  3. The mass matrix and the coupling matrix of bending and torsion vary with the time concern to the deflections of the system when the nonlinear inertial term and the geometric non - linearity term are comprised in the dynamic formulation

    文中推導的動力學有限元方程中的一致質量矩陣m和彎扭耦合矩陣?都考慮了幾何非線性項和非線性慣性項，因此是與系統變形有關的時變矩陣。
  4. Taking account of the simplified torsion moment of inertia, integral stability coefficient increase relatively 5 % or 0. 01 ~ 0. 03 absolutely, only for narrow rolled h - section ( hn ) behind hn350 175, whose calculation length goes beyond the limit of 8 meters

    Gb50017中扭轉慣性矩的簡化使規格大於hn350 175的hn型鋼，在計算長度大於8米時，整體穩定系數偏高5 ，絕對偏大量在0 . 01 0 . 03范圍。
  5. In the system of “ direct measurement ” of inertia brake, the braking torque is measured by the right torque sensor of inertia brake. in the thought of special construct of inertia brake, the work braking test data of inertia brake is analyzed, mathematic differential equation is founded, the variable situation of braking torque is analyzed through program calculation, some problem is discovered and suggestion is put forward to the application of test rigs and inertia brake

    在慣性制動器的「直接測量」系統中，用慣性制動器右端的扭矩傳感器來測量制動力矩的，考慮到慣性制動器特有的結構，對慣性制動器工作制動試驗數據進行分析，建立了數學微分方程，通過編程計算分析了制動力矩的變化情況，發現了問題並對試驗臺和慣性制動器的應用提出了改進建議。
分享友人
分享到 Line

分享到臉書