拉伸熱處理 的英文怎麼說
中文拼音 [lāshēnrèchǔlǐ]
拉伸熱處理
英文
drawing-heat treating- 拉 : 拉構詞成分。
- 伸 : Ⅰ動詞（展開） stretch; extend Ⅱ名詞（姓氏） a surname
- 處 : 處名詞1 （地方） place 2 （方面; 某一點） part; point 3 （機關或機關里一個部門） department; offi...
- 理 : Ⅰ名詞1 （物質組織的條紋） texture; grain （in wood skin etc ） 2 （道理;事理） reason; logic; tru...
- 熱處理 : [冶金學] heat treatment; heat treating熱處理保護塗料 heat treatment protective coating; 熱處理車...
-
Four kinds of filament with different content of baso4, 60 %, 70 %, 75 %, 80 %, were heat - treated. post - treatment process parameters of the filament were different with the concentration of baso4 changing
通過對60 % ， 70 % ， 75 % ， 80 %四種不同baso ;含量的纖維進行后加工熱定型處理，從纖維拉伸實驗可以看出:不同baso ;含量的纖維后加工工藝參數不同。Cu - zn - cr - zr conducting bar alloy and cu - cr - zr end ring alloys used for superpower asynchronous traction motor rotor were prepared by ingot metallurgy. using hardness measurement, tensile test at room and higher temperature, electrical resistance test at room and higher temperature, optical microscopy, xrd, sem, and tem, the mechanical and electric properties and the microstructure of above alloys at different treatment were studied. them were also analysed and explained in theory
採用鑄錠冶金法制備了大功率異步牽引電動機轉子用導條合金和端環合金，通過硬度測試、室溫拉伸、高溫拉伸、電導率測定、金相分析、 xrd 、 sem 、 tem等方法研究了不同加工工藝和熱處理工藝對上述合金力學性能、導電性能及其組織結構的影響和變化規律，並從理論上進行了分析和解釋。Characteristics : as a result of cold processing aging heat treatment, this product has a tensile strength of over 1100mpa
特性：通過冷間加工時效熱處理，拉伸長度達到1100mpa以上The results showed that with the increase of heat treatment temperature, both the carbon content and tensile modulus of carbon fibers were enhanced, however the linear density decreased
試驗結果表明，隨著熱處理溫度的提高，炭纖維線密度下降，微晶層間距縮小，碳含量、微晶尺寸和拉伸模量得以提高。The results of the experiments show that the ti3al - tcll dual alloys, by vacuum - electron - beam weld, hot die forging and 680c / 12h, ac, heat treatments, have satisfied synthesis properties of intensity, plasticity, hardness. and also it is the feasiblie way. this will establish the supporting technology for the manufacture of the compress disk in the areoengine
實驗結果表明，經真空電子束焊接ti _ 3al ? tc11雙合金經過熱模鍛造和680 12h ， ac或815 1h + 700 8h ， ac熱處理后，焊接區組織過渡均勻，可以使得焊縫處強度在室溫拉伸時高於ti _ 3al ，而在600拉伸時高於tc11合金，獲得強度、塑性、硬度均令人滿意的綜合性能，且是一條可行的工藝路線。Insulating and sheathing materials of electric and optical cables - common test methods - methods specific to polyethylene and polypropylene compounds - tensile strength and elongation at break after conditioning at elevated temperature - wrapping test after conditioning at elevated temperature - wrapping test after thermal ageing in air - measurement of mass increase - long - term stability test - test method for copper - catalyzed oxidative degradation
電纜和光纜的絕緣和護套材料.通用試驗方法.聚乙烯和聚丙烯化合物專用方法.高溫處理后抗拉強度和斷裂伸長度.高溫處理后的卷繞試驗.在空氣中熱老化后的卷繞試驗.質量增加的測量.長期穩定性試驗.催化銅氧化降解的試驗方法Specification for hex cap screws, bolts, and studs, steel, heat treated, 120 105 90 ksi minimum tensile strength, general use
通用最低拉伸強度為120 105 90 ksi的熱處理鋼制六角頭螺釘螺栓和螺柱的規范Insulating and sheathing materials of electric and optical cables - common test methods - part 4 - 2 : methods specific to polyethylene and polypropylene compounds - tensile strength and elongation at break after conditioning at elevated temperature - wrapping test after conditioning at elevated temperature - wrapping test after thermal ageing in air - measurement of mass increase - long - term stability test - test method for copper - catalyzed oxidative degradation
電纜和光纜的絕緣和護套材料.通用試驗方法.第4 - 2部分:聚乙烯和聚丙烯化合物專用方法.高溫處理后抗拉強度和斷裂伸長度.高溫處理后的卷繞試驗.在空氣中熱老化后的卷繞試驗.質量增加的測量.長期穩定性試驗.催化銅氧化降解的試驗方法Sealants - determination of adhesive and cohesive force by endurance tensile strength after thermal treatment
密封劑.熱處理後用耐久拉伸強度測定粘附力和內粘聚力測定Sealants - determination of adhesive and cohesive force by tensile strength test until rupture after thermal treatment
密封劑.熱處理后進行拉伸試驗直至拉斷時的粘附力和內粘聚力測定The tensile strength of carbon fibers generally lowered than that without heat - treatment, and the decreased value was various with the different temperature treatment
高溫處理導致炭纖維拉伸強度發生較大損失，在本次試驗中，在不同的熱處理溫度下，纖維強度下降的程度不同。分享友人