拉制 的英文怎麼說
中文拼音 [lāzhì]
拉制
英文
wiredrawing; drawing拉制玻璃 [材料] drawn glass; 拉制車間 drawing mill; 拉製件 [冶金學] draw piece; drawn part; 拉制金屬 draw metal; drawn metal; 拉制設備 drawing device; 拉制試驗 drawing test-
Natural diamond die is one the best for the drawing of precision wires. the diamond is selected meticulously to be complete grains with good. symmetry free from any foreign substances. it is prepared with advanced powdermetallurgicaltechnology that makes the diamond with the strongest strength and antiknock property during the processes
天然金剛石拉絲模對于各種精密線材的拉制是最好的模具之一,採用的天然金剛石是經過精心挑選的,必須是顆粒完整對稱性好,沒有雜質,又採用先進的粉末冶金技術鑲套從而使金剛石在拉拔過程中獲得最大的強度和抗爆裂能力。Jiangpai natural diamond die is one the best for the drawing of precision wires. the diamond is selected meticulously to be complete grains with good symmetry free from any foreign substances. it is prepared with advanced powder metallurgical technology that makes the diamond with the strongest strength and antiknock property during the processes
江牌天然金剛石拉絲模對于各種精密線材的拉制是最好的模具之一,採用的天然金剛石是經過精心挑選的,必須是顆粒完整對稱性好,沒有雜質,又採用先進的粉末冶金技術鑲套從而使金剛石在拉拔過程中獲得最大的強度和抗爆裂能力。Then after analysising each characteristics of phosphate glass material, the fiber rod - in - tube by invaginating core rod, inside cladding and outside cladding is used to fabricate the er / yb phosphate glass fiber successfully by polishing and vacuumizing fiber rod - in - tube. finally some techniques, such as cladding pump, prism coupling pump and fusing pump are used to measure the gain of fiber amplifiers
最後對拉制出的光纖提出了包層泵浦、棱鏡耦合泵浦和熔接耦合泵浦三種可行的增益和傳輸特性測試測方案,並針對鉺鐿共摻磷酸鹽玻璃光纖的特性,指出了熔接耦合是測試增益和傳輸特性的最佳方案。The screw and barrel of extruder are made of high quality 38crmoala allay steel, the hardness is over hv950 after nitrogenizing treatment
再生料粉料或顆粒料拉制扁絲。擠出機的螺桿機筒採用Drawn sheet glass. general
拉制玻璃板.概述Glass in building - basic soda lime silicate glass products - drawn sheet glass
建築用玻璃.基本的鈉鈣玻璃製品.拉制薄板玻璃Hard - drawn copper round trolley wires
硬拉制圓形電車導線Hard - drawn grooved trolley wires
硬拉制凹槽電車導線Based on the fact of driven gear moving prior to normal locality when driving gear pair moving from upper dead center to lower dead center, considering all influential elements, the maximum backlash of gear pair can be controlled to satisfy the special driving requirement through controlling the length and deviation of its common normal without increasing its manufacture precision
摘要根據換向傳動齒輪副從上止點向下止點運動時被動齒輪運動超前的實際,從影響齒輪副側隙的各種因素出發,在不提高齒輪副製造精度的前提下,通過拉制齒輪副公法線長度及其偏差從而有效地控制齒輪副的最大齒側間隙,以滿足傳動的特殊要求。Wrought drawn rods and bars
銅及銅合金拉制棒Hardmetal dies for drawing wires and bars - types and dimensions
硬質合金拉制模具型式和尺寸Aluminium and aluminium alloys - drawn wire - tolerances on dimensions
鋁和鋁合金.拉制絲材.尺寸公差Hexagon drawn bars in aluminium alloys
鋁合金拉制六角形棒材Round drawn bars in aluminium alloys
鋁合金拉制圓棒材Hard alloy die is made y taking high - quality hard alloy as its nips and fastening with steel die case. it is characterized by high hardness, good thermal conductivity, brasive coefficient and strong resistant to corrosion. it is suitable for drawn metal wire, bar and pipes. the types of dies includes rectangle, hecagon, octagon, diamond, trapezoid, basin and knob, u - shaped and half round types
硬質合金模具採用優質合金作模芯,並用鋼質模套緊固,具有硬度高,導熱性能好,磨擦系數小,抗腐蝕性等特點,適用於拉制金屬線材,棒材,管材等,另外,模具的類型有矩型、六角型、八角型、菱型、梯型、凹型凸型、馬蹄型、半圓型等各種異形模。Rolling bearings - needle roller bearings, drawn cup without inner rings - boundary dimensions and tolerances
滾動軸承.拉制的杯形無內環滾針軸承.外形尺寸和公差Rolling bearings. needle roller bearings, drawn cup without inner rings. boundary dimensions and tolerances
滾動軸承.無內套環的拉制軸承環滾針軸承.外型尺寸和公差Drawn glass fiber
拉制的玻璃光纖B. for hard and half hard drawn tubes the ratio of outer diameter to wall thickness is no more than 25
硬態和半硬態拉制管外徑與壁厚之比不小於25者。Hard - drawn aluminium wires for electric purposes
電氣用硬拉制鋁線分享友人