拉削加工 的英文怎麼說
中文拼音 [lāxiāojiāgōng]
拉削加工
英文
ziehrumen pull broaching-
Some of them are of advanced ones, such as 5 - face grinding machine, electronic beam perforator, vacuum brazing equipment, curvic coupling grinding machine, controlled atmospheric quenching over, 4 - axis and 5 - axis nc milling machines, equipment for multi - component impregnation, heavy - duty grinder and high speed broacher, etc
擁有先進的五面磨床電子束打孔真空釬焊圓弧端磨可控氣氛淬火爐和四軸五軸數控銑床以及多元共滲強力磨削快速拉削等一批先進加工設備。Common process instructions for cutting. process instructions for broaching
切削加工通用工藝守則.拉削High speed cutting, water jet machining and laser machining technology are applied to kevlar fiber reinforced resin matrix composites and special kind rubber materials. valuable conclusions are obtained by experimenting investigation in chapter 8
論文在第八章還進行了凱芙拉纖維增強聚合物基復合材料、特種橡膠材料的高壓水射流、激光和高速切削加工試驗研究，取得了有參考價值的結論。Various successive partial plastic forming methods for processing groove, including thread rolling, cross rolling and skew rolling, splitting, rolling of spline shaft, split rolling, open - die extrusion of spline shaft / gear, extrusion of internal screwed tooth socket parts with large helical pitch, integral cold forging for slot commutator, extrusion - ploughing for outside fin tube, drawing of tube with spiral internal / external ribs etc. have been introduced briefly
摘要介紹了用於加工槽的各種連續局部塑性成形方法，包括螺紋軋制、橫軋與斜軋、分劈、花鍵軸滾軋、劈分軋制、花鍵軸齒輪開模擠壓、花鍵套擠壓、槽型換向器整體冷鍛、外翅片管擠壓一犁削、內外螺紋管拉拔等。Machining deformation of aircraft monolithic component is simulated by finite element method ( fem ) and validated by experiment. the initial residual stress in pre - stretched plate is generated by simulating quenching and stretching processes. with a single tool - tooth milling process fem, the machining loads in monolithic component material removing is obtained. restart - calculation is put forward to complete the whole simulation of machining process. to verify the fem result, an experiment is carried out. the deformation distribution of the monolithic component resulting from fem shows a good agreement with the experiment result, which indicates that the key technologies presented in the paper are practicable and can be used to simulate the milling process of monolithic component to predict its deformation. lengthy and expensive trial and error experiment process can be avoided
在模擬淬火、拉伸過程獲得含有初始殘余應力的預拉伸板材以及模擬單齒切削過程獲得切削載荷的基礎上，提出並採用接力演算法，對一航空整體結構件的材料銑削過程進行有限元模擬，同時進行了試驗研究.結果表明，有限元模擬的整體結構件的變形與試驗具有一致性，從而證明提出的整體結構件加工模擬關鍵技術的可行性，避免了為研究加工變形而進行的繁瑣的試錯法Through these studies and analysis, following conclusions could be drawn : ( 1 ) it is necessary to study on harness engineering of landslide and dangerous rock since the main representations of this geological hazard are landslide and dangerous rock through geological investigation ; ( 2 ) it can be concluded though stability analysis that the dingzhuang landslide is stable naturally, which is identical to the in - situ investigation ; ( 3 ) through stability analysis, the landslide would slide if the water level dropped down from 175. 10m to 156. 0m and it rained successively after the three gorges reservoir work. ( 4 ) according to the results of calculation and the characteristic of the landslide, it is suggested that such measures as unloading at upper part, anchorage and pile supporting system and drainage system should be used on the landslide. ( 5 ) according to geological investigation, there are three kinds of dangerous rock in the engineering, those are failing - down rock, collapsing rock and sliding rock
因此有必要對滑坡進行治理； （ 4 ）根據滑坡推力計算結果和本滑坡屬牽引式滑坡的特點，滑坡體上部相對較穩定，中下部處于基本穩定或不穩定狀態，因此建議此滑坡治理採用上部削坡減載與錨拉抗滑樁、擋墻進行支擋結合的處理方法，同時結合截排水等措施進行綜合治理； （ 5 ）根據地勘資料，通過對危巖體的形態、規模、基座和底界層及分佈特點和分析，將本工程危巖體失穩崩塌的方式歸納為墜落式、傾倒式和滑塌式三種類型並分別提出相應的穩定性計算方法； （ 6 ）分別對本工程中的危巖體進行了穩定性計算，並且發現其都處于不穩定狀態，因此根據實際情況分別提出相應襯砌支撐和清理等加固治理措施，最後還對加固后的危巖體進行了校核計算，滿足要求。Manufacturing processes chip removal - part 5 : broaching ; classification, subdivision, terms and definitions
排屑加工工藝.第5部分:拉削.分類細分類術語和定This series product can also be used as metal process molding agent, lubricant and cutting fluid for metal feathering, punching or forming, grinding cool finish, welding agent and lubricant in paper making
用作金屬加工鑄模劑、金屬拉絲、沖壓或成型的潤滑劑及切削液，研磨冷卻拋光劑、焊接劑、造紙工業中作潤滑劑。Finally, the technic route for the research of milling distortion is proposed. in chapter 4, the effect of tool path and clamping schemes on residual stresses as well as machining distortion are analyzed by using three - dimensional elastic - plastic fem ( finite element method ). the distortion variation tendency under four typical tool paths, the pressing - plate clamping and stretched fixation is obtained respectively
第四章基於上述理論基礎，利用三維彈塑性有限元技術分析了走刀路徑和裝夾方案對銑削加工殘余應力分佈和變形的影響，得到了四種典型的走刀路徑以及壓板式裝夾和拉伸裝夾對加工變形的影響趨勢。Provide manufacture services of rubber - ware pressing process machine, roller bearing oiling, rubber - ware grinding and cutting
提供皮棍壓套羅拉軸承加油皮棍磨削加工服務。分享友人