拉力屈服點 的英文怎麼說

中文拼音 [lālìqūbìdiǎn]
拉力屈服點 英文
tensile yield point
  • 拉 : 拉構詞成分。
  • 力 : Ⅰ名1 （力量; 能力） power; strength; ability; capacity 2 [物理學] （改變物體運動狀態的作用） forc...
  • 服 : 服量詞（用於中藥; 劑） dose
  • 點 : Ⅰ名詞1 （液體的小滴） drop （of liquid） 2 （細小的痕跡） spot; dot; speck 3 （漢字的筆畫「、」）...
  • 拉力 : pulling; pulling force; thrust; traction; tension拉力表 draw bar [pull] dynamometer; 拉力測定儀 [...
  1. Through the strong pulling tests of four kinds of synthetic fiber filter cloth, the mechanical performance index of the filter cloth in dry and wet conditions were measured, the influence of various pulling speeds on the fracture strength and the fracture tensile rate of the filter cloth was derived. it was concluded that the stress of the filter cloth could relax when it was beyond the yield point

    通過4種合成纖維濾布的強力拉伸試驗，測得了濾布在干、濕兩種狀態下的力學性能指標，得出了不同拉伸速度對濾布斷裂強度和斷裂伸長率的影響，同時指出當濾布的應力超過屈服點時，會出現應力松馳現象。
  2. For the obvious yield point of angle steel, the critical frictional resistance could be regarded as ultimate pullout capacity

    對具有明顯屈服點的鋼材，在實際施工中，可以把摩阻臨界值作為極限拉力。
  3. In terms of strength and ductility, the concept of specified yield point is put forward. based on the principle that under the same condition ( that is, the size of cross section, material strength and reinforcement ratio are identical ), the resultant ultimate moment must be identical, the compression failure of frp reinforced concrete beam is equal to the tension failure for the viewpoint of design and calculation

    從強度與延性兩方面的綜合考慮，提出了纖維增強塑料筋名義屈服點的概念，對發生受壓破壞的纖維增強塑料筋混凝土梁，按照同樣條件下（截面尺寸、材料強度、截面配筋率等均相同）截面承載力相等的原則等效轉化為受拉破壞進行設計與計算，以此確定纖維增強塑料筋的強度折減系數_ f 。
  4. Through analysis and compare, the measure fitting for huxi bank was put forward. ( 3 ) introduced fast lagrangian analysis of continua. flac3d is a three - dimensional explicit finite - difference program. it can simulate the behavior of three - dimensional structures built or soil, rock or other material and can simulate plastic collapse, flow and large - strain accurately

    （ 3 ）對三維快速拉格郎日有限差分法進行了介紹，三維快速拉格朗日法是一種基於三維顯式有限差分法的數值分析方法，它可以模擬巖石或土體及其它材料的三維力學行為，可以準確模擬材料的屈服、塑性流動、軟化直至大變形，尤其在材料的彈塑性分析、大變形分析以及模擬施工過程等領域有其獨到的優點。
  5. The mesh of finite element was generated automatically to simulate the true fabric of concrete. the different material property of elements was identified and assigned automatically. the nonlinear constitutive relation of materials was established

    採用非線性本構模型來表徵組成三級配混凝土的各種材質的非線性應力?應變關系，該本構模型具有可以模擬材料的開裂、拉伸軟化、塑性屈服和壓碎非線性等特點。
分享友人
分享到 Line

分享到臉書