拉模 的英文怎麼說

中文拼音 [lāmó]
拉模 英文
broaching die
  • 拉 : 拉構詞成分。
  • 模 : 模名詞1. （模子） mould; pattern; matrix 2. （姓氏） a surname
  1. A die plate for flattening metal into strips, as in the manufacture of watch springs

    扁條拉模一種用來拉平鋼條的模板，如用於生產手錶發條的模板
  2. 4. we can classify the enterprise green transition into three kinds by the dominant factor in the push - drag - model, push - dominant mode, drag - dominant mode and friction - tight state. different green policies should give to different transition mode in odor to getting a good green effect

    4 、本文建立了企業綠色變遷推拉模型，並根據促使企業綠色轉變的主導因素的不同，將企業綠色變遷的模式分為拉力主導型、推力主導型與摩擦狀態三種類型，不同的類型應採取不同的綠色政策才能收到良好的綠色效果。
  3. Sleeved tube drawing mandrels

    第2部分:套管拉模芯
  4. Guiding parts, mandrels, calibration rolls, knives, plate cutters, inserts for percussion drills, masonry drill tips, calibration bushes, drawing cheeks, shearing knives, inserts for golfer shoes

    導向部分、心軸、校準軋輥、刀片、倒盤、沖擊鉆機的襯墊、鉆機鉆頭、校準襯套、拉模夾具、剪刀、高爾夫鞋的襯墊。
  5. Is actually the driving service behind both the push and pull models ; however, in the latter case it operates implicitly

    實際上是推模型和拉模型背後的驅動服務；但在拉模型中它是隱式操作的。
  6. Hexagon bar drawing dies for non - ferrous metal

    有色金屬六方棒材的拉模
  7. Ningbo yinzhou xinfeng mould factory was set up in 1992, has been specialized in making all series of horniness mould, drawplate, die and different type mould etc, now has 16 employees, the products according to the drawing or sample from clients, the annual throughput reach 1. 2 million pieces

    寧波市鄞州鑫峰模具廠創建於1992年，私營獨資企業，前身為鄞縣百靈拉絲模廠，長期以來專業生產各種系列硬質合金模具、拉模、縮模、沖模及各種規格異型模。
  8. Shaped drawing dies for steel of square and flat section

    方鋼及扁鋼型材的成形拉模
  9. Pure eulerian model for simulating dilute spray combustion

    液霧燃燒的全歐拉模型數值模擬
  10. Diamond dies for wires of ferrous and non - ferrous metals

    黑色和有色金屬線材用金鋼石拉模
  11. Wire bar or tube drawing dies - as sintered pellets of hardmetal

    線棒和管拉模用硬質合金模坯
  12. Wire, bar or tube drawing dies - as sintered pellets of hardmetal

    線棒和管拉模用硬質合金模坯
  13. . wire, bar or tube drawing dies. as - sintered pellets of hardmetal carbide. dimensions

    絲材，棒材或管件拉模.硬質合金
  14. Wire drawing dies for steel

    鋼絲拉模
  15. Die reduction angle

    拉模孔圓錐角
  16. Analysis indicates the " low pressure closed reticular flow region " results in the non - equilibrium of pressure along the primary jet ' s orifice. to obtain as large vectoring angle as possible, the optimal ranges of angles, frequencies, velocity amplitudes, and distances from the microjet actuator to the primary jet exit were discussed. the relationship between the vectoring angle of the primary jet and the phase - difference of two adjacent actuators was analyzed

    分析了「拉」模型單作動器模式下，微射流作動器的入射角度、驅動頻率、速度幅值及與主射流間的距離對主射流偏轉程度的影響，並確定了作動器工作參數的最佳范圍;分析了「拉」模型雙作動器模式下，不同的相位差對主流偏轉程度的影響。
  17. Using the diecast method, products with cleaner and more accurate dimensions can be produced than is the case with other casting methods

    與其它澆注法比，通過拉模鑄造製造的產品外觀更美，尺寸更精確。
  18. To manage the clean and maintenance of the pultrusion tools

    對擠拉模具進行清洗、維護和修理。
  19. These technologies provide useful building blocks for monitoring and discovery, enabling us to define properties for which we can provide monitoring and discovery, as well as subsequent pull - and push - mode access, as we ll see here

    這些技術為資源的監控和發現提供了有用的構建塊，並使我們可以定義一些監控和發現的屬性，以及隨后進行的推和拉模式的訪問，正如您將在本文中所看到的。
  20. Directing towards the inefficient trouble existing in information acquiring, the article reasonably distributes the active abilities between suppliers and requirers through the analysis of intelligent push - pull technology, and brings forward respectively the intelligent push - pull information model based on internet and intranet

    針對當前信息獲取存在效率不高問題，本文通過對智能推拉技術進行分析和研究，將信息服務的主動能力在提供者和需求者之間進行合理的分配，分別提出基於internet和intranet智能信息推拉模型。
分享友人
分享到 Line

分享到臉書