振動刀 的英文怎麼說

中文拼音 [zhèndòngdāo]
振動刀 英文
vibration cutter
  • 振 : 動詞1. （搖動; 揮動） shake; flap; wield 2. （奮起） brace up; rise with force and spirit
  • 刀 : Ⅰ名詞1 （切、割、削、砍、鍘的工具） knife; sword 2 （形狀像刀的東西） sth shaped like a knife 3 ...
  1. This machine uses reciprocating piston topour, sort caps out with electromagnetic shaking, pricks caps with blade. it not only can automatically finish the bottle - feeding, pouring, arranging caps, sending caps, pricking caps, but also not pout and arrange caps without bottle. it is a perfect equipment of little measure oral liquid pouring and cap - pricking

    本機採用往復式活塞泵進行灌裝，電磁振蕩理蓋，刀片軋蓋。能自動完成進瓶灌裝理蓋送蓋軋蓋工序，且無瓶不灌裝無瓶不理蓋。
  2. In this study, based on bispectrum and bicoherence extraction of vibration acceleration signals at spindle end of a vertical machining center while milling operation, change rules of bispectrum and bicoherence of the signals were analyzed for the progressive wearing process of the flank wear land of the milling cutters

    通過提取銑削加工過程中機床主軸端振動加速度信號的雙譜及其雙相干系數，分析了銑刀后刀面漸進磨損過程雙譜及其雙相干系數的變化規律。
  3. The results show that vibration parameters have a great effect on the surface roughness and the tool life

    在精密車床上進行了金剛石刀具超聲振動切削不銹鋼零件的加工實驗。
  4. A diagnostic method for tool breakage of nc millingmachine based on vibration signals

    基於振動信號的數控銑床刀具破損診斷方法
  5. When the frequency approaches zero, the factor approaches zero correspondingly ; 2 ) the amplitude of interaction factors changes with the incident angle of rayleigh waves and reaches maximum when is zero. moreover, with the increase of, the wave period shortens apparently ; ( 3 ) the amplitude of interaction factors decreases as the pile spacing increases and approaches to zero when the pile spacing is 15 ; 4 ) the amplitudes of interaction factors increase clearly with the increasing stiffness ratio of pile to soil ; 5 ) the lat eral seismic response of fixed - head pile groups is much smaller than that of free - head pile groups. moreover, the pile - group effects induced by rayleigh waves can be neglected ; 6 ) the lateral seismic response of piles at different location differs from each other

    得到了以下結論： 1 ）樁的相互作用因子隨頻率呈周期性變化，在振動頻率比較低的情況下，樁的橫向相互作用因子也較低，當頻率趨近於零時，相互作用因子也趨近於零； 2 ）樁的相互作用因子的幅值隨瑞利波入射角度的變化而變化，在= 0情況下幅值最大，且隨入射角度的增加，波動的周期明顯縮短； 3 ）樁的相互作用因子的幅值隨著樁與樁間距的增加而減小，至s d = 15時，樁的相互作用因子基本趨近於0 ； 4 ）在頻率比較低時，相互作用因子幅值隨樁土相對剛度比的增加而顯著增加； 5 ）樁頂固接可以有效地降低群樁的橫向地震響應幅值，由瑞利波產生的群樁效應可以忽略不計； 6 ）群樁中不同樁位的樁的橫向地震響應是不同的，每根樁所在的樁位對其橫向地震響應有很大的影響；刀樁數的增加並不能減小樁的橫向動力響應。
  6. Mechanical vibration - measurement and evaluation of the grip and feed forces for assessing the exposure of the hand - arm system to vibration

    機械振動.遭受振動的手臂體系評定用夾緊力和進刀力的
  7. The method samples the signals of spindle vibration displacement and the spindle electrical machinery power signal using the synchronized sampling technique. as the two kinds of signals are all non - contact pick - ups, this method is very suitable for the machining centre

    對加工中心銑刀破損監測，提出了利用主軸振動位移信號和機床主電機功率信號進行監測的方法，由於採用非接觸測量，非常適合於加工中心等柔性加工設備。
  8. The effects of vibration parameters on the surface roughness and the tool wear are analyzed

    研究了不同振動參數對工件表面粗糙度和刀具磨損量的影響規律。
  9. If adjustment is required, turn adjustment control with screwdriver in either direction slowly until vibration or hum stops

    如果需要調節，則用螺絲刀從兩個方向慢慢旋轉調節控制，直到振動或蜂鳴聲停止。
  10. The rotary radius is 27cm and the rotary speed of the blade axle is 1800rpm. ( 5 ) the effect of pressure of twin inclined presswheels on emergence rate under different soil moisture have been compared in field

    考慮到實際作業效果，又考慮到播種機重心高低對穩定性和振動大小的影響，最終選取刀片旋轉半徑為27cm ，刀軸轉速為1800r / min 。
  11. Knock it on arm and the body of it will resonate and crack. it ' s hard on surface, which can ' t be moved by swiss sword ! strange

    在手臂上敲擊，劍身產生共振，斷裂的；給老鄉5張老革命了賬，學費心疼啊！劍的表面硬度很高，我用瑞士刀卡中的銼刀頭劃不動！奇怪？
  12. Ultrasonic vibration is applied to diamond turning of stainless steel in order to decrease diamond tool wear and improve the surface quality of the workpieces

    摘要為減輕金剛石刀具的磨損，提高工件表面加工質量，採用超聲振動的方法切削不銹鋼零件。
  13. Environment vibration will cause vibration displacement between the work piece and the tool, influencing the accuracy and surface quality of work piece

    環境振動會引起切削刀具與被加工零件間的相對振動位移，影響被加工零件的精度和表面質量。
  14. Experiments of diamond turning of stainless steel are taken on a fine lathe by utilizing ultrasonic vibration

    對刀具的振動頻率和振幅的影響進行了理論分析。
  15. The 113 - year - old company, which in four years has undergone dramatic restructuring at the cost of thousands of jobs in the face of the technology crash and economic malaise, will launch the marketing push on september 13

    面對技術股崩盤和經濟不振的局面，有著113年歷史的飛利浦， 4年來以犧牲成千就業崗位的代價，進行了大刀闊斧的重組，公司將於9月13日發起上述全球營銷活動。
  16. Computer tomographic scan and magnetic resonance imaging showed a mass lesion in the left basal ganglion region

    因無法以核磁共振掃瞄及腦部血管攝影檢查排除為動靜脈畸形瘤，於是開刀取樣化驗。
  17. Then the de - lay differential method of detecting the milling cutter breakage is put forward according to the above research work and the changing characteristics of power signal and vibration displacement signal when the tool breakage occurs, the monitoring stategy of sensors fusion based on the artificial neural network is put forward. the monitoring system of milling cutter breakage based on the information fusion of the power signal and vibration displace - ment signal has been developed. the diff culty in giving a dectecting threshold due to the changeable character of character of cutting condition has been solved, and a good reliability is ensured over a wide range of conditions

    在上述研究工作的基礎上，提出了基於人工神經網路用於多傳感器信息融合的監測策略，開發研製了以機床主電機功率信號和主軸振動位移信號特徵參量融合的銑刀破損監測實驗系統，解決了銑削過程中切削條件多變導致監測閾值難以設置的難題，保證了在較寬的工作范圍內具有較高的識別準確率。
  18. In the machining process, the vibration signals of the tools can be gathered by the data acquisition card, and then the turning tools wear monitoring model is built after the signals are filtered through the method of multivariate statistical analysis

    在加工過程中，數據採集單元實時採集刀具的振動信號，經過數字濾波，運用多元回歸建模技術，建立了車削過程刀具磨損監測模型。
  19. The lateral vibration of the high speed rotating disk cutter slice blade was studied by the finite element analysis and the experimental measurement

    摘要針對高速旋轉圓盤刀具薄刀片實際工作時存在的橫向振動問題，應用有限元方法及實驗測量進行了研究。
分享友人
分享到 Line

分享到臉書