控制柄 的英文怎麼說

中文拼音 [kòngzhìbǐng]
控制柄 英文
bale arm
  • 控 : 動詞1 （告發;控告） accuse; charge 2 （控制） control; dominate 3 （使容器口兒朝下 讓裏面的液體慢...
  • 制 : Ⅰ動詞1 （製造） make; manufacture 2 （擬訂; 規定） draw up; establish 3 （用強力約束; 限定; 管束...
  • 柄 : Ⅰ名詞1 （器物的把兒） handle 2 （植物的花、葉或果實跟莖或枝連接部分） stem 3 （言行上被人抓住的材...
  • 控制 : control; dominate; regulate; govern; manage; check; cybernate; manipulate; encraty; rule; rein; c...
  1. Design philosophy of hardware and software is established. the paper bases control algorithm of operator and control program diagram on thorough investigation into truck crane operation reliability action flow, which makes sure of accurate and effective control over handle and accelerograph and achieves test process automatization

    文章在深入研究汽車起重機作業可靠性試驗動作流程的基礎上確定了對執行機構的控制演算法，並給出控製程序框圖，準確有效地實現了對操縱手柄及油門的控制，達到試驗過程自動控制的目的。
  2. Cross feed control lever

    橫向進刀控制手柄
  3. Buffering code assumes that it exclusively controls the handle

    緩沖代碼假定它以獨占方式控制該句柄。
  4. Objects draw the grab handles for the control

    對象為控制項繪制抓取手柄。
  5. Objects representing the selection borders and grab handles for a standard control

    對象的集合，其中的對象表示標準控制項的選擇邊框和抓取手柄。
  6. Draws a container control grab handle glyph on the specified graphics surface and within the specified bounds

    在指定的邊界內、指定的圖形表面上繪制容器控制項抓取柄標志符號。
  7. Operation of the manual open handle also disables any local or remote closing operation until the handle is reset. once reset, the recloser can be closed using the control

    手動分開關操作的同時也閉鎖了就地或者遠方控制命令，直到手柄復位才使重合器解除閉鎖狀態。
  8. Car retarder lever

    車輛減速器控制手柄
  9. ( 3 ) planar full - crank five - bar mechanisms without uncertainty singularity are chosen to construct a hybrid mechanism generating the given path. a mathematical model is set up to optimize the dimensions of five - bar mechanism with the minimal power consume of the controlling motor by the improved genetic algorithms. an example is given to show the effectiveness of the mathematical model

    （ 3 ）第四章中，選取全曲柄五桿機構中的三種類型機構作為混合驅動機構，以減少用於控制其一連架桿運動的步進電機所消耗的功率為目的，建立相應的數學模型，用改進的遺傳演算法對該五桿機構進行優化綜合，求得尺寸參數。
  10. Specific means is preexistence reaction spot is located inside chosen acupuncture point area, the handle that use a needle ( or match rod ) press pressure, its have the place of tenderness to be reaction dot namely, radish is stuck with adhesive plaster after disinfection child ( turnip seed ), after affixing fat acid bilges feeling can, choose 3 every time 5 point, pressure after sticking fat or the parent, daily proper motion is pressed press 3 4 times, change every week, or so ear undertakes alternately, such holding to that treat 1 3 months, what can control children is fat

    具體方法是先在選用的穴區內找出反應點，用針柄（或火柴棍）按壓，其有壓痛的部位即為反應點，消毒後用膠布粘萊菔子（蘿卜籽）一粒，貼上之後胖兒有酸脹感即可，每次選3 5個穴位，壓貼后胖兒或家長，每日自行按壓3 4次，每周換一次，左右耳交替進行，這樣堅持治療1 3個月，能夠控制兒童的肥胖。
  11. Control by grabbing one of the corner sizing handles and dragging

    控制項的大小，方法是抓住某個角尺寸柄並拖動它。
  12. Principles : model pmqzq permancent magnet lifter has strong magnetic path produced by nd - fe - b magnetic materials. on and off of the magnetic path is controlled by turning the manual handle

    永磁起重器是由強磁釹鐵硼磁性材料組成磁路系統，產生強磁，通過手柄的旋向，控制磁路關閉，達到工作目的。
  13. Principles : permanent magnet lifter has strong magnetic path produced by nd - fe - b magnetic materials. on and off of the magnetic path is controlled by turning the manual handle. permanent magnetic lifters have magnet as power. and its lifting power will never weaken

    永磁起重器是由強磁釹鐵硼磁性材料組成磁路系統，產生強磁，通過手柄的旋向，控制磁路關閉，達到工作目的，永磁起重器採用磁做動力，工作長久不變。
  14. Gets the style that indicates whether or not the move handle is visible

    獲取指示移動控制柄是否可見的樣式。
  15. Gets the rectangle representing the area in which to paint the move handle

    獲取一個矩形，表示要在其中繪制移動控制柄的區域。
  16. Gets the style that indicates whether the move handle is displayed vertically or horizontally

    獲取樣式，指示是垂直還是水平顯示移動控制柄。
  17. An application can obtain a handle to a process that can be used as a parameter to many process - information and control functions

    應用程序可獲取進程句柄，該句柄可用作許多進程信息函數和控制函數的參數。
  18. Bolt lock lever

    聯鎖箱控制握柄
  19. Retrieves the control that contains the specified handle

    檢索包含指定句柄的控制項。
  20. Method associates the control s handle with a message map to be used by the generic window procedure

    方法將控制項的句柄與通用窗口過程
分享友人
分享到 Line

分享到臉書