控制棒材料 的英文怎麼說

中文拼音 [kòngzhìbàngcáiliào]
控制棒材料 英文
control rod material
  • 控 : 動詞1 （告發;控告） accuse; charge 2 （控制） control; dominate 3 （使容器口兒朝下 讓裏面的液體慢...
  • 制 : Ⅰ動詞1 （製造） make; manufacture 2 （擬訂; 規定） draw up; establish 3 （用強力約束; 限定; 管束...
  • 棒 : Ⅰ名詞（棍子） stick; staff; club; cudgel Ⅱ形容詞[口語] （強; 高; 好） strong; excellent; good
  • 材 : 名詞1 （木料） timber 2 （泛指可以直接製成成品的東西; 材料） material 3 （供寫作或參考的資料） ma...
  • 料 : 名詞1 （材料; 原料） material; stuff 2 （喂牲口用的穀物） feed; fodder 3 （料器） glassware 4 （...
  • 控制 : control; dominate; regulate; govern; manage; check; cybernate; manipulate; encraty; rule; rein; c...
  • 材料 : 1. （原料） material 2. （資料） data; material 3. （適于做某種事的人才） makings; stuff
  1. The results indicated that, the fabrication process of ultra - fine grain material is mainly determined by the stress, rotate speed and the flux of cooling water. the grain refining and the hardening effect are mostly affected by the rotate speed and the flux of cooling water. compared with commercial ly12, the invalidate strength and the prolongation rate of the ultra - fine grain material are properly improved in the measurement of compression property ; and the abrupt change of the dilatability of the ultra - fine grain material at 500c is found ; also the phenomena of which the grain size of these microstructures is stable when annealed under 300c is observed

    研究表明，採用本文提出的摩擦壓扭強變形區轉移法可以得到棒狀的超細晶材料，軸向壓力、扭轉速度和溫度是採用該方法制備超細晶材料的主控參數；試件的旋轉轉速和冷卻速度對變形區晶粒細化和硬化效果影響顯著；超細晶ly12的壓縮性能與淬火+自然時效狀態的ly12壓縮性能相比，斷裂強度和延伸率均有一定程度的增強；超細晶ly12的熱膨脹系數在550左右發生明顯的變化。
  2. Uses : as an activator of various phosphor, especially red phosphor, also as the material of bar in nuclear reactor

    用途：用作各種彩色熒光粉，尤其是紅粉的激活劑，也是核反應堆中子控制棒的材料。
  3. Approaches must be carried to deal with this problem. in this paper, metal material, nylon plastics, phenolic cotton cloth laminated tube and 3 - d composite material is respectively used as one of the linkages. we compare these four systems to test the performance of light material in mechanism

    為此，本文分別採用金屬、尼龍棒、酚醛棉布模壓棒以及三維編織復合材料製作機構中最長的連桿構件，通過四套系統進行對比實驗研究，檢驗東華大學碩士學位論文機械01碩呂繼超指導教師:王生澤輕質材料對于優化系統控制性能的影響。
  4. We draw the conclusion that nylon plastic and phenolic cotton cloth laminated tube are helpful to control system. 3 - d composite material ca n ' t be used in the industry for the limiting of curing tech

    結果表明，輕質的尼龍棒和層合復合材料?酚醛棉布模壓棒有助於提高系統控制性能;而三維編織復合材料由於固化工藝限制，尺寸和剛性均暫時無法滿足工業使用。
  5. Liquid - solid extrusion of composite material is a new kind of metal forming process, which has been developed in recent years with a promising practical application prospect for its simple working procedure, low cost and good workpiece performance. but it is difficult to set up an accurate mathematical model because the process is a multivariable nonlinear time varying system. so this process ca n ' t be put into practical uses for the difficulties in process parameters control

    復合材料管、棒材液-固擠壓成形工藝是近幾年發展起來的一種金屬成形新工藝，具有工序少、成本低、製件性能好等特點，應用前景廣闊，但該工藝是一多變量非線性時變系統，很難建立精確的數學模型，過程參數難于控制，限制了該工藝的實際應用。
分享友人
分享到 Line

分享到臉書