控制返回 的英文怎麼說

中文拼音 [kòngzhìfǎnhuí]
控制返回 英文
return of control
  • 控 : 動詞1 （告發;控告） accuse; charge 2 （控制） control; dominate 3 （使容器口兒朝下 讓裏面的液體慢...
  • 制 : Ⅰ動詞1 （製造） make; manufacture 2 （擬訂; 規定） draw up; establish 3 （用強力約束; 限定; 管束...
  • 返 : 動詞（回） return
  • 回 : 回構詞成分。
  • 控制 : control; dominate; regulate; govern; manage; check; cybernate; manipulate; encraty; rule; rein; c...
  • 返回 : return; go [come] back; revert; recurrence; throwback
  1. Returns the device - specific adapter for the control

    返回控制項的設備特定適配器。
  2. Returns the adapter - specific view for a control

    返回控制項的特定於適配器的視圖。
  3. As we are masters of ulm, we cannot lose the advantage of remaining masters also of both sides of the danube ; and moreover able, should the enemy not cross the lech, to pass over the danube at any moment, throw ourselves upon their line of communications, recross the danube lower down, and entirely resist the enemys aim if they should attempt to turn their whole force upon our faithful ally

    因為我們佔有烏爾姆，我們則可繼續控制多瑙河兩岸的有利形勢因此，如果敵人不橫渡萊希河，我們定能隨時渡過多瑙河，沖至敵人的交通線，並從多瑙河下游渡河返回原地，如果敵人慾以全部兵力進犯我們的忠實盟軍，我們決不允許敵人實現這一企圖。
  4. Object for paginating the contents of the given control

    創建和返回用於對給定控制項的內容進行分頁的
  5. Press set key at one sec is setting control value. it is set value display s number after display s - u, press or key can recompose set value, range is 1560, again press set key is backing out display the measure value. it can automatism backing out display the measure value after three sec, if it is dont press any key

    1按set鍵1s設置控制值，顯示s - p后顯示的數字為設定值，按上下鍵可修改設定值，范圍為- 50100 ，再次按set鍵返回顯示測量值，不按任何按鍵3s后也可自動返回顯示測量值。
  6. Method returns control back to the caller

    方法將控制返回給調用方之前立即激發
  7. Might never return control to your program

    可能永遠不會將控制返回您的程序。
  8. Returns control to the calling thread immediately

    立即將控制返回給發出調用的線程。
  9. Which, in turn, returns control to its caller the method

    方法） ，它又將控制返回給其調用者（
  10. Control returns to the calling procedure

    控制返回到調用過程。
  11. Returns control to the code that called a

    將控制返回給調用
  12. Command single steps an instruction and returns control to kdb

    命令單步執行指令然後將控制返回給kdb 。
  13. In flag values that control the kind of module that is initialized

    [ in ]控制返回的發射器類型的標志值。
  14. Finally, control is returned to

    最後，將控制返回
  15. Procedure performs a task and then returns control to the calling code

    過程執行任務，接著將控制返回到調用代碼。
  16. Wait until the operation completes before returning control to the calling program

    ）的調用一直等到操作完成後才將控制返回給調用程序。
  17. Any such method callback function can execute synchronously or asynchronously with respect to the remote caller, and the caller cannot make any assumptions about completion of such a call when execution control returns to it. in addition, calling the

    任何此類方法回調函數都可以相對于遠程調用方同步或異步執行，而該調用方在執行控制返回到它時不能對此類調用是否完成做任何假設。
  18. Return statement terminates execution of the method in which it appears and returns control to the calling method

    語句終止它出現在其中的方法的執行並將控制返回給調用方法。
  19. Though each get call goes back to the user, you don t have to save state, or restore state when control comes back to you

    雖然各個get調用都返回到用戶，但不必保存狀態，也不必在控制返回時恢復狀態。
  20. Two main contents of designing the database are proposed, one is to retrieve zipped data according to some rules, which is fulfilled by a few procedures together and can be controlled by input parameters. anther is to clear up the real - time data stored in database timely, which is fulfilled by using dts function in sql server 2000, and the data out of time can be deleted or saved as a access file

    數據庫的設計中最重要的是兩個內容，一個是要將壓縮的離散的數據按照一定的規律返回，這個任務是由幾個存儲過程協同完成的，可以輸入參數控制返回；另一個是，實時數據大量積累在數據倉庫中，要定時清理過期數據，因此使用microsoftsqlserver2000的數據導入導出工具dts完成了過期數據的刪除或者選擇保存為access文件。
分享友人
分享到 Line

分享到臉書