控制閉塞系統 的英文怎麼說

中文拼音 [kòngzhìbìsèxìtǒng]
控制閉塞系統 英文
controlled manual block system
  • 控 : 動詞1 （告發;控告） accuse; charge 2 （控制） control; dominate 3 （使容器口兒朝下 讓裏面的液體慢...
  • 制 : Ⅰ動詞1 （製造） make; manufacture 2 （擬訂; 規定） draw up; establish 3 （用強力約束; 限定; 管束...
  • 閉 : Ⅰ動詞1. （關; 合） close; shut 2. （堵塞不通） block up; obstruct; stop up Ⅱ名詞（姓氏） a surname
  • 系 : 系動詞（打結; 扣） tie; fasten; do up; button up
  • 統 : Ⅰ名詞1 （事物間連續的關系） interconnected system 2 （衣服等的筒狀部分） any tube shaped part of ...
  • 控制 : control; dominate; regulate; govern; manage; check; cybernate; manipulate; encraty; rule; rein; c...
  • 系統 : 1. （按一定關系組成的同類事物） system 2. （有條理的;有系統的） systematic
  1. In order to overcome the disadvantages of servo valves and the spool valves, the fast hydraulic system controlled by the fast on - off valve is researched which uses the on - off valves as the pilot valves. they are used to control the opening and closing of the logic valves, thus they can control the pressure and the flow. so they can control the movement direction and the velocity of the piston

    為了克服伺服閥和滑閥的不足，本文所研究的基於快速開關閥的快速液壓系統採用快速開關閥作先導閥，控制邏輯閥的開啟和關閉，從而控制液流的通斷和壓力的高低、流量的大小，以實現對活塞運動方向、速度的控制。
  2. Piston ring is the important accessory of the engine and turning its contour is the key procedure to ensure the performance of piston ring it has great value in economy and society that we develop the nc machining system for outer circle of piston ring to manufacture the high quality piston ring and to replace the import machine according to piston ring contour data provlded by the cad system ， it can turn the piston ring contour by controlling the displacement of servomechanism which is controlled by the angle of servo motor it uses the theories of velocity closed loop 、 dlsplacement closed loop and feed forward control to improve the control precision of system on the basis of theories of elastic mechanics and mathematics ， the cad system can provide the accurate data required by the nc machine system according to the calculation model and the parameters of piston ring this system integrates the cad cam technology

    系統根據活塞環cad系統生成的介面數據，通過伺服電機的轉角位置控制自主研製的高性能微位移進給機構產生給定的位移，以完成活塞環輪廓的仿型加工。系統採用速度、位置閉環控制及前饋控制理論，以提高系統的控制精度。活塞環cad系統以彈性力學和數學方法為基礎，根據常用的計算模型與活塞環參數自動生成數控加工系統所需的精確的介面數據，實現cad / cam一體化。
  3. We discuss structure of the end - to - end congestion control schemes with active queue management ( aqm ) in ip network from the control theoretic point of view. and propose a fuzzy logic based aqm which can improve the robustness of the control algorithms. give out the detailed simulations

    本文從擁塞控制的角度出發，強調路由器隊列管理在系統控制中的地位，並從閉環控制的角度出發，描述擁塞控制的結構，研究主動隊列的控制系統模型，設計了一種用於主動隊列管理（ aqm ）的模糊控制器，模擬證明了這種aqm演算法的有效性。
  4. In order to fulfil the requirement of metro operation, fullback modes and the relative control modes are introduced in the signaling moving block system in different occasions of failure this paper discusses the design principle of fullback control mode from the aspects of safety, reliability and usability

    摘要從滿足地鐵運營組織的需要出發，分析、介紹了移動閉塞系統各類故障情況下的降級模式和相關控制方式，從安全性、可靠性、可用性的角度闡述了移動閉塞系統降級控制模式的設計原則。
  5. Secondly, on the basis of the basic structure of the brake control system, the theory of brake task programming is studied and analyzed thoroughly. on the condition of automatic train protection, the fixed block system and moving block system the brake task programming method is brought forward

    其次，本文從制動控制系統的基本結構出發，對制動任務規劃理論進行了詳細的研究和分析，分別提出了在基於安全防護、固定閉塞和移動閉塞三種不同應用條件下的制動任務規劃方法。
分享友人
分享到 Line

分享到臉書