提閥式發動機 的英文怎麼說
中文拼音 [dīfáshìfādòngjī]
提閥式發動機
英文
poppet-valve engine-
Finally, because high - speed power solenoid valve is one of the most important executive parts in the electronic control diesel engine and the performances of diesel engine are strongly related to the solenoid valve, the response performance of the solenoid valve is investigated. the response performance of the solenoid is influenced by many factors, such as driving voltage, electric driving unit etc. in order to have high excitation voltage and in low maintaining voltage, a high - low voltage electric driving unit is designed, and in order to make the solenoid valve close more rapidly, an active free - wheeling circuit and a bootstrapping circuit are designed in the electric driving unit, too. in the high - low electric driving unit, high voltage and low voltage are supplied by the dc - dc device and by the accumulator respectively
高速強力電磁閥的響應性能除了與閥本身的結構和材料有關外，與驅動電壓、驅動電路的設計密切相關，本文通過分析，首先開發出一種高低壓驅動電路，高壓電源是山升壓式dc - dc原理獲取的，低壓由蓄電池本身提供，實現高壓強激和低壓維持的功能，電路中採用有源續流電柴汕機中卜軌知介系統的設訓及其七川j敝略的叭究路進行續流，加誣了電磁閥的關閉速度；採用自舉吐路，降低了場效應管對驅動電壓的要求。Yet, most existing high speed on / off valves use electromagnet as their electicity - mechanism conversion element, and good performant electromagnets have to be imported from other countries, in such situation, it is difficity to make excelent high speed electromagnet valve made in our country, even if we can make good performant high speed electromagnet valve in our country, it still has the shortcoming of not high enough respond speed, too small placket and big volumeo in this thesis, a new high speed on / off valve is developed based on two types of existing valves, this new valve has higher respond speed, a little big placket and little volume o for the new valve, several main task was made out as below : a ) several types of high speed on / off were first analyzed, then the basic performance of the actuator of the new valve was analyzed
高速開關閥是20世紀80年代發展起來的一種具有響應速度快、抗污染能力強、與電子電路配合好等特點的一個良好的動力放大元件。但是現有的高速開關閥基本上採用電磁鐵為電?機轉換元件，高性能的電磁鐵又基本為進口，難以滿足高性能高速開關閥國產化的要求，即使是高性能的電磁鐵式高速開關閥，仍存在著響應速度不夠大、開口過小、體積較大的缺點。本文在現有兩種高速開關閥的基礎上，設計了一種新穎的高速開關閥，在提高其動態性能的同時，增大了閥的開口，減小了閥的體積。According to the present problems and developing tendency of hydraulic turbine governor, four main issues of this field are studied in this paper. the content include hydraulic control system, frequency measurement unit, stability of the discrete control system, optimization of control parameters and self - adjusting pid control strategy based on fuzzy logic. several main achievement and results are obtained and shown as follows : the electric - hydraulic pilot valve driven by step - motor is firstly proposed, which solves the problem that the electric - hydraulic converter of hydraulic turbine governor hydraulic servo is prone to be stuck and blocked and improves the systemic stability greatly
本文根據水輪機調節領域存在的問題和發展趨勢，對水輪機調速器的液壓控制系統、頻率測量環節、離散調節系統穩定性與調節參數最優整定以及適應式參數自調整pid控制策略進行了研究，得到以下主要成果和結論：首次提出了採用步進電機驅動的步進式電液引導閥，從根本上解決了水輪機調速器電液隨動系統中存在的電液轉換元件發卡、堵塞問題，使電液隨動系統的可靠性大大提高。The jimi company grasps " the customer for reveres, the goodfaithservice, the fast delivery, the outstanding quality " the idea to serve the general customers, the company had been established until now, provide sastation type fastener necessary service for the pump valve profession, the engine profession, the water - treating equipment, the chemical machinery, the electronic profession, the mechanical profession and so on
吉米公司秉持「顧客為尊、誠信服務、快速交貨、優異品質」的理念來服務廣大客戶，公司成立至今，為泵閥行業、發動機行業、水處理設備、化工機械、電子行業、機械行業等眾多廠家提供一站式緊固件配套服務。In order to solve the problems that large energy consumption, temperature variation, high, cost trouble maintenance in current electro - hydraulic servo control system for material testing machine, a new design scheme that electro - hydraulic proportional control system for material testing machine based on extension control strategy is proposed. the design scheme is successful by means of designing new main frame system, hydraulic cylinder system, digital electro - hydraulic micro - fluid proportional valve and electrical control system, and its results lay a foundation for material testing machine industries in our country
針對國內外材料試驗機主要採用電液伺服控制系統，存在能耗大、溫升、成本高、維護困難等問題，本課題提出了基於可拓控制策略的材料試驗機電比例負載適應控制系統這一新型研究方案，通過開發新型試驗機主機系統、液壓缸系統、數字式微小流量電液比例流量閥及電控系統，實現了材料試驗機電液比例負載適應控制，為我國材料試驗機自動控制系統的產業化打下了基礎。Based on the self - industry and the application of the other trade on auto - control technique, this paper advances the frame of the control and management system - beer - pack2000, develops supervisory control interfaces for beer - filled process, and designs the control system by omron for opening value, inspecting and brushing the broken bottle. at last, this paper advances the thought of controlling the liquid and press in storing tank by pid, simulates and lines up the parameter by simulation software - matlab
在windows98環境下，用組態王軟體開發了啤酒灌裝生產線的監控界面，用組態王內部提供的模擬plc實現了動畫連接；並用日本omron系列可編程式控制制器設計了閥開啟、破瓶檢測、破瓶沖洗、自動落蓋等過程的自動控制；最後提出了用控制方面較為成熟的pid演算法來控制全自動灌裝壓蓋機貯液缸內液位和壓力的想法，並用模擬軟體matlab的動態模擬環境simulink對其參數進行了模擬整定。分享友人