換向齒輪 的英文怎麼說

中文拼音 [huànxiàngchǐlún]
換向齒輪 英文
idle gear
  • 換 : 動詞1. （給人東西同時從他那裡取得別的東西） exchange; barter; trade 2. （變換; 更換） change 3. （兌換） exchange; cash
  • 齒 : Ⅰ名詞1 （牙; 牙齒） tooth 2 （物體上齒形的部分） a tooth like part of anything 3 [書面語] （年齡...
  • 輪 : Ⅰ名1 （輪子） wheel 2 （像輪子的東西） wheel like object; ring; disc 3 （輪船） steamer; steamboa...
  • 齒輪 : gear [rack; toothed] wheel; （toothed） gear; wheel gear
  1. Based on the fact of driven gear moving prior to normal locality when driving gear pair moving from upper dead center to lower dead center, considering all influential elements, the maximum backlash of gear pair can be controlled to satisfy the special driving requirement through controlling the length and deviation of its common normal without increasing its manufacture precision

    摘要根據換向傳動齒輪副從上止點向下止點運動時被動齒輪運動超前的實際，從影響齒輪副側隙的各種因素出發，在不提高齒輪副製造精度的前提下，通過拉制齒輪副公法線長度及其偏差從而有效地控制齒輪副的最大齒側間隙，以滿足傳動的特殊要求。
  2. A kind of long - strike oil pumping machine using planet - gear

    一種行星齒輪長沖程抽油機的換向機構研究
  3. Thereby measures for improvement are put forward : ( 1 ) adopting a small wheel to replace the steel ball of the ball type unit to ensure more reliable motion of the creeping device ; ( 2 ) applying expansible metallic ring replacing the step - by - step teeth on tooth type unit ; ( 3 ) fixing a sensor in the reversing device for obtaining the information of motion and wear of the creeping device

    為此，提出改進措施： 1 .對球型步進式清蠟器採用帶穿軸的小輪代替鋼球，可使爬行器運動更可靠； 2 .對齒型步進式清蠟器，採用可脹緊金屬環代替步進齒，金屬環依靠抽油機的沖程力脹大后使爬行器固定，反沖程力使金屬環縮小； 3 .將傳感器裝在換向器內，根據信號的時間間隔判斷爬行器的運行速度及磨損等情況。
  4. With continuous wavelet transform as feature extraction method and neural network as classifier, a transmission ge ar wear estimation system is designed and applied in estimating the wear condition of the gear

    以連續小波變換作為變速箱齒輪的磨損特徵向量的提取方法、以神經網路作為分類器，設計了變速箱齒輪的磨損估計系統，並應用於變速箱齒輪的磨損狀況估計。
  5. Various successive partial plastic forming methods for processing groove, including thread rolling, cross rolling and skew rolling, splitting, rolling of spline shaft, split rolling, open - die extrusion of spline shaft / gear, extrusion of internal screwed tooth socket parts with large helical pitch, integral cold forging for slot commutator, extrusion - ploughing for outside fin tube, drawing of tube with spiral internal / external ribs etc. have been introduced briefly

    摘要介紹了用於加工槽的各種連續局部塑性成形方法，包括螺紋軋制、橫軋與斜軋、分劈、花鍵軸滾軋、劈分軋制、花鍵軸齒輪開模擠壓、花鍵套擠壓、槽型換向器整體冷鍛、外翅片管擠壓一犁削、內外螺紋管拉拔等。
  6. Mechanical commutation ( graphite or precious metal brushes ), highest efficiency, low inductance, low electromagnetic interference, multiple combination possibilities with gears, feedback devices and control electronics

    機械換向器（石墨和金屬電刷） ，高效率，小電感，電磁干擾小，能與多種齒輪箱，反饋設備和控制電子元件配合使用。
  7. Bevel gear reverse

    錐齒輪換向法
  8. Gear power transmission is mainly through gear meshing to transmit power, realizing reducing and increasing speed or changing direction

    齒輪傳動主要是通過齒輪的嚙合作用來傳遞動力及實現減速、增速或換向的目的。
  9. Based on the study of wavelet analysis theories and on the analysis of gear transmission vibration, continuous wavelet transform multi - resolution analysis and wavelet packet decomposition are respectively studied and applied in extracting the feature vectors of transmission gear extraction methods, then these three feature extraction methods are compared and useful conclusions yield

    本文應用小波分析方法，針對變速箱齒輪運行過程中的振動信號的特點，研究了基於連續小波變換、小波分析的多分辨分析和小波包分解的變速箱齒輪振動信號的特徵向量提取方法，並將這些方法進行比較，得到了有用的結論。
分享友人
分享到 Line

分享到臉書