摩擦圓 的英文怎麼說

中文拼音 [mócāyuán]
摩擦圓 英文
friction circle
  • 摩 : 摩構詞成分。
  • 擦 : 動詞1 （摩擦） rub 2 （用布、 手巾等摩擦使干凈; 揩拭; 抹） wipe; scrub; clean 3 （塗抹; 搽） spre...
  • 摩擦 : 1 （互相接觸的兩物體作來回相對運動） rub; chafe 2 [物理學] （相互接觸的兩物體在接觸面上發生阻礙相...
  1. Disc friction clutch

    圓盤摩擦離合器
  2. Cone friction gear

    圓錐摩擦傳動
  3. Friction characteristics of oscillatory laminar flow in straight tube

    圓直管內層流振蕩流的摩擦特性
  4. Being a sort of new principle micromotor in the fronitier of science. the ultrosonic motor ( usm ) is developed at recently twenty years. utilizing the stator surface particle elliptical motion excited by piezoceeramics, the usm is drived by friction force between the stator and rotor. compared with the conventional electromagnetic motor, the ultrasonic motor has the following features : high speed, high holding torque when power is off and so on. because of it ' s characteristics, the ultrasonic motor has obtained some widespread application in robots, precise instrument, house electronical appliance, sapceecraft automobile and micromechanism

    超聲波電機（ ultrasonicmotor ）是近二十年來發展起來的一種新原理電機，其原理不同於傳統的電磁型電機，它是利用壓電陶瓷的逆壓電效應使定子的表面質點產生橢圓運動，通過定子和轉子之間的摩擦力驅動轉子運動。這種新型的電機與傳統電磁電機相比，具有響應快、不受電磁干擾、結構緊湊、低速、大扭矩、斷電自鎖等優點，因而在微型機械、機器人、精密儀器、家用電器、航天器、汽車等方面顯示出廣泛的應用前景。
  5. ( 6 ) in this paper. adopting fea software ansys to simulation and analysis the al ecap process. in order to spread out studying of ecap in the future. the results show : die comer angle, the radius of round angle, the friction coffience of workpiece and die, the properties of die ( elastic modulus, possion ratio ) et al, have some degree impact on the deformation of materials

    （ 6 ）採用有限元（ fea ）分析軟體ansys對al的擠壓過程進行ecap模擬與分析，為后續研究工作做好鋪墊，分析結果表明：外切角、圓角半徑、試樣與凹模之間的摩擦系數、凹模本身的特性（如彈性模量、泊松比等）等等，對材料的變形量都由不同程度的影響。
  6. The springback angle increases with the increase of the punch round radius and clearances between the punch and the die while decreases with increase of the blank holder force, sheet thickness, friction coefficient and material hardening exponent

    回彈角隨凸模圓角半徑和凸凹模間隙的增大而增大，隨壓邊力、板料厚度、摩擦系數和材料硬化指數的增大而減小。
  7. In this paper, the drive theory of the large ratio friction transmission is studied ; a new type elliptical cam wave generator is designed ; the large ratio friction transmission prototype is designed and manufactured ; based on the ansys finite element method software, structure of the elliptical cam is analyzed ; precision index of the manufactured large ratio friction transmission prototype, such as transmission accuracy, least step, stability of the least step, load capacity is measured by the absolute rotary encoder. by analyzing the measurement data and research content, it is think that the new elliptical cam wave generator could overcome a good many problems brought by processing errors, facilitate size precision adjustments, input moment can be achieved in the form of a pure force couple importing ; through this study, " the large ratio friction transmission prototype " could apply in practical engineering basically

    本文研究了大速比摩擦傳動的傳動理論;設計了新型橢圓凸輪波發生器，設計製作了大速比摩擦傳動樣機;用軟體ansys對所設計的橢圓凸輪結構進行了有限元分析;用19位絕對式編碼器測試了大速比摩擦傳動機構的傳動精度、最小步距、最小步距的穩定性以及帶負載能力等各項精度指標;對測量數據和研究內容進行了歸納和整理，認為新型橢圓凸輪波發生器克服了加工誤差帶來的諸多問題，新型橢圓凸輪波發生器可以進行尺寸精度調整，能夠達到輸入力矩以純力偶的形式輸入;通過本項研究，基本可以使「大速比摩擦傳動機構」在工程中得以應用。
  8. This method is of high reliability and efficiency. it ' s regarded the one of the best designing method nowadays. to choose the best parameter of frication piece and make sure that the cloth ' s mechanical function is the aim of friction piece ' s parameter priority

    為了圓滿解決上述兩個問題，本文採用廣義既約梯度法對摩擦片參數、變速器傳動比及變速器二軸六檔齒輪進行了優化設計，該演算法可靠性和效率都很高，是目前公認最為優秀的優化方法之一。
  9. Squeeze flow between two parallel disks is considered for small gaps for rigid - plastic material with partial wall slip. firstly, the coulombic friction condition is discussed, and a new pressure distribution is obtained

    首先對現有的庫侖摩擦條件下的壓力規律做了進一步的研究，找到了一種更合理的圓盤上的壓力分佈規律。
  10. Moreover, based on the assumption that the slip velocity at the disks increases linearly with the radius up to the rim slip velocity, another pressure distribution is derived by introducing a appropriate velocity field. then these different results by the different friction conditions and technique are compared. 2

    同時，在圓盤邊緣處滑移速度一定，介質的滑移速度隨著半徑線性變化的假設下，引入合理的速度場，得到了另一種圓盤上的壓力分佈規律，並對不同的摩擦條件及用不同方法計算得到的結果進行了對比。
  11. On both pins friction decreases with increasing twist.

    兩種圓桿上摩擦都隨紗線捻度的增加而減少。
  12. Based on the review, the fluid flow and heat transfer in the curved circular and rectangular pipes have been researched by employing perturbation method and numerical simulation with a physical model under the rotational orthogonal curvilinear coordinate in a rotating curvilinear pipe with multi - parameters. we firstly analyzed the fully developed fluid flow and heat transfer, mixed convection heat transfer, the development of flow and heat transfer in the inlet in different cross section ( circular, elliptical, annular and rectangular crossection ). the variations of the secondary flow, axial velocity, distribution of temperature, the friction force on the wall, the ratio of friction factor as well as the nusselt number with different dimensionless parameters had been examined in detailed

    本文在總結和分析了一個世紀以來有關曲線管道流動和換熱特性的研究成果的基礎上，以旋轉正交曲線坐標系統下的多參數旋轉螺旋管道中的對流傳熱為物理模型，通過攝動方法和有限體積法，首次對各種截面（圓截面、橢圓截面、環形截面、矩形截面）旋轉曲線管道內充分發展流動的流動結構和傳熱特性（包括耦合對流傳熱特性）以及旋轉曲線管道開口段發展流動的流動結構和換熱特性進行了系統的數值模擬和理論分析，詳細討論了各種無量綱參數對管道內軸向速度分佈、二次流結構、溫度分佈、壁面摩擦力、摩擦系數比以及管道nusselt數的影響，獲得了若干創新性成果。
  13. It utilizes two boltclamped langevin transducers with unanimous frequency characteristic which convert vertical vibration to flexural traveling wave. they are arranged on the place of a elastic pipe to generated traveling - wave. when the traveling - wave propagate, the particles on the elastic pipe traverse an elliptic trajectory, materiel is transported by friction or acoustic streaming

    利用兩套頻率特性一致並以縱向振動方式工作的夾心式換能器，通過合理的布局在導管中激勵出行波，使輸送管管壁質點產生橢圓運動，從而利用摩擦或在液體中產生聲流來實現固體及液體的傳送。
  14. Firstly, the hertz contact theory is used to design the export moment of the prototype ; deformation status of the flexspine under the elliptical cam wave generator action is analyzed using the column shell theory, whose boundary condition is four force action. design proposal of the wave producer put forward considering the precision theory of rolling friction transmission

    首先用赫茲接觸理論對樣機的輸出力矩進行了設計;應用四力作用下的光滑圓柱殼體理論分析了在橢圓凸輪波發生器作用下柔輪的變形狀況，結合滾動摩擦副傳動精度理論提出了波發生器總體設計方案。
  15. Application of disk friction pump in axis seal

    圓盤摩擦泵在軸封中的應用
  16. Loading capacity analysis of multiple - disk clutches in the consideration of error of axial force

    考慮軸向力損失的多圓盤摩擦離合器的工作能力分析
  17. ( 5 ) as torsion is increased, the anticlockwise secondary vortexes and the negative area of the stream function increase ; the axial velocity moves anticlockwise ( annular pipe ) or clockwise ( circular pipe ) ; the friction factor ratio finally reaches the value about 1

    （ 5 ）增大撓率，逆時針方向旋轉的一二次渦和流函數的負值區域增大，軸向速度最大值的位置按逆時針（環形截面）或順時針（圓截面）方向旋轉，摩擦系數比最終趨向於1 。
  18. In this paper, a rub disc movement decomposition organization is firstly analyzed and proved to be a nonholonomic system. in fact, it is a speed changing mechanism the radio of which is variable

    本文分析了一種摩擦圓盤傳動機構的運動原理，證明了該結構的為非完整機構的條件，並總結出該結構的實際上為我們可以認為非完整傳動機構實質上就是一種變傳動的變速機構。
  19. Friction circle method

    摩擦圓法
  20. After the topological structure of machine system and the method of conversion of coordinate are introduced, 3d model of the manipulator had been set up in pro / e. in the process, several problems had been solved, such as simplification of part model, assembly, idealization of rub disc movement decomposition organization

    在介紹了軟體中機械繫統的拓撲結構和坐標變換的方法后，在pro e中建立了機械手的3d模型；解決了模型建立過程中的零件模型的簡化、零件的裝配、摩擦圓盤機構的理想化、模型中電動機的轉動方向等問題。
分享友人
分享到 Line

分享到臉書