摩擦損失系數 的英文怎麼說

中文拼音 [mócāsǔnshīxìshǔ]
摩擦損失系數 英文
friction lo coefficient
  • 摩 : 摩構詞成分。
  • 擦 : 動詞1 （摩擦） rub 2 （用布、 手巾等摩擦使干凈; 揩拭; 抹） wipe; scrub; clean 3 （塗抹; 搽） spre...
  • 損 : Ⅰ動詞1 （減少） decrease; lose 2 （損害） harm; damage 3 [方言] （用尖刻的話挖苦人） speak sarcas...
  • 系 : 系動詞（打結; 扣） tie; fasten; do up; button up
  • 數 : 數副詞（屢次） frequently; repeatedly
  • 摩擦 : 1 （互相接觸的兩物體作來回相對運動） rub; chafe 2 [物理學] （相互接觸的兩物體在接觸面上發生阻礙相...
  • 損失 : 1. （失去） lose 2. （失去的東西） loss; wastage
  • 系數 : [數學] coefficient; ratio; modulus; quotient; factor
  1. In order to improve the prediction accuracy, the sensitivities of pipe friction coefficients, pressure loss coefficients in bents, wall temperatures and heat transfer coefficients in pipes and cylinders on the volume efficiency are investigated

    為提高充氣效率的計算精度，由模擬計算和相關試驗，分析了管道的摩擦系數、彎管的壓力損失系數、進氣管壁和氣缸壁溫度及其傳熱系數對充氣效率的影響程度。
  2. The results show that the heat transfer in intake manifold and cylinder has obvious effects on the volume efficiency, while the pipe friction coefficients and bent pressure loss coefficients have less effect

    結果表明，進氣管和氣缸的傳熱對充氣效率的影響較顯著，而管道摩擦系數和彎管壓力損失系數對充氣效率的影響較小。
  3. In the third chapter, the mathematical models of project system have been established, and simulation has been done on the simulink enviroment of matlab software kits. the simulation focus on the effects of main parameters on the dynamic characteristics of speed control system, and the main parameters include viscosity damp coefficient and friction torque of electrical motor shaft, internal leakage coefficient of pump / motor of hydraulic circuits, gas volume of pressure accumulator, viscosity damp coefficient of cylinder piston and different running building floors, etc. at last, theoretical research effects of the flow and pressure pulsation of pump / motor on car speed and oil volume leakage theory are discussed. the fourth chapter of this thesis concerns the research on the key items about hydraulic power control system according to the ens 1 - 2 and other hydraulic elevator standards

    論文第三章針對組成系統的各個模塊進行了機理建模，並且通過matlab軟體中的simulink圖形化模擬環境進行了本課題系統的模擬研究，主要針對影響系統特性的主要參數變化，動態分析系統的輸出特性，在上下行工況中，分析了電機軸系粘性阻尼系數、軸系摩擦力矩、主迴路蓄能器迴路液壓泵馬達內泄漏系數、蓄能器氣體容積、液壓缸柱塞粘性阻尼摩擦系數以及不同運行樓層工況等參數對系統特性的影響；最後對軸向柱塞泵馬達的流量壓力脈動對電梯轎廂速度的影響和蓄能器內油液體積損失機理進行了理論研究。
  4. In this paper, ptfe and ptfe composited with sicp, sicw, mos2p and sicp + mos2p with various ratios respectively have been obtained by compression molding. under the condition of dry friction, a systematic study has been done on the weight loss and the friction coefficient of composites and the relations between the properties and content of the filling, the load and the sliding velocity

    在干摩擦滑動磨損條件下，對ptfe材料及其復合材料的磨損失重、摩擦系數及磨損機理進行了研究，同時對其與磨損外部條件（載荷、滑動速度）和材料的內部因素（填料的含量、粒徑、種類）的關系進行了較為系統的研究。
  5. At first, the soft of bridge structure, gqjs, is used to calculate the structure of prestressed concrete continuous beam bridge and the deformation and stress of the concrete box beam are given out ; then by measuring and analyzing the datum of the stress in the prestressed steel rope and the stress of section in the concrete box beam, this article presents two ways to identify the reasonable friction deviation factor k between longitudinal prestressed tendons and the wall of duct ( indirectly and directly ), and discover the regular pattern of prestressed friction loss

    首先運用橋梁結構分析專用軟體gqjs對預應力混凝土連續梁橋進行結構計算，得到了各施工工況下混凝土箱梁的撓度和截面應力；然後給出了識別引起結構預應力損失的孔道偏差系數k的兩種方法（間接法和直接法） 。通過對測得的預應力索沿程應力和混凝土箱梁截面應力數據的分析處理，得到了合理的預應力孔道摩擦偏差系數及預應力摩阻損失規律。
分享友人
分享到 Line

分享到臉書