摩擦熱 的英文怎麼說

中文拼音 [mócārè]
摩擦熱 英文
attritional heat
  • 摩 : 摩構詞成分。
  • 擦 : 動詞1 （摩擦） rub 2 （用布、 手巾等摩擦使干凈; 揩拭; 抹） wipe; scrub; clean 3 （塗抹; 搽） spre...
  • 摩擦 : 1 （互相接觸的兩物體作來回相對運動） rub; chafe 2 [物理學] （相互接觸的兩物體在接觸面上發生阻礙相...
  1. Ptfe has many excellent properties such as : bonzer self - lubrication ^ low fricatiom chemistry stabilization and thermal stabilization, but its wear resistance is very low to improve the wear resistance of ptfe a lot of researches have been down by means of adding fillers to it, there are still less report on nano - inorganic filler filled ptfe composites to change properties. in this paper, experimental study was made to question above problem

    Ptfe具有優異的自潤滑、低摩擦、化學穩定性和熱穩定性，但耐磨性較差，因而人們在利用不同種類的填料對ptfe進行填充改性，提高耐磨性方面作了大量研究工作，但在使用納米無機填料填充改性ptfe方面研究很少，因此本課題主要探討這一方面的問題。
  2. Semimetal non - asbestos environmental protection automobile brake shoe with stable friction indexes, contractible heat fade, excellent performance in high temperature, strong friction resistance, long working life and stable brake, small noise, fine energy absorption, no asbestos, no pollution, ect characteristics. complied with international standard, it s a ideal brake article for users

    本公司研製生產的半金屬無石棉環保型汽車剎車片，具有摩擦系數穩定，熱衰退縮小，高溫段穩定性能好，耐磨性強，使用壽命長，制動平穩，制動時噪音小，能量吸收效果好，無石棉，對環保無污染等特點，符合國際規范，是廣大用戶的理想的剎車製品。
  3. This depends on the estimation of the temperatures generated by frictional heat.

    它取決于摩擦熱所引起的溫度估算。
  4. On the basic theory of transfer heat, tribology of rolling bearings and rotor dynamics, taking gdz48a electrospindle as an example, the paper puts forward the spindle bearing ' s quasi - dynamics analysis model with the influences of the friction heat and preloadings analyzes the friction moment, velocities, contact loads, friction heat and stiffness and studies the influences of the friction heat, structure and application parameters on the speed and dynamics

    本文以傳熱學、滾動軸承摩擦學和轉子動力學為理論基礎，以gdz48a型電主軸為例，建立了考慮摩擦熱和預緊方式影響的主軸軸承擬動力學分析模型，分析了軸承的摩擦力矩、運動、載荷和剛度，研究了軸承的熱特性、設計和應用參數對速度和動力學性能的影響，並進行了試驗驗證。
  5. The heat expansion coefficient of casting nylon materials is about 10 times larger than steel, so the internal dia shrinks caused by the expansion. it will influence the connection gap of the abrasive surface

    鑄型尼材料的熱膨脹系數約比鋼材大10倍左右，所以軸套在運行時由於摩擦熱所造成的膨脹變形使內徑縮小，影響摩擦面的配合間隙。
  6. ( 2 ) it is found that distilled water as lubricant can markedly reduce the accumulation of friction heat and temperature rise on the frictional surfaces of polymer. so the heat fatigue and adhesive wear decrease. moreover, a lubricating film forms on the interface between the counterpart and polymer when distilled water acts as polar lubricant

    （ 2 ）潤滑劑水的存在，可大幅度降低聚合物磨損表面的摩擦熱積累及溫升，從而減少了基體的熱疲勞磨損和粘著磨損，同時，水作為一種極性潤滑劑，在摩擦界面上能形成一層潤滑膜，對摩擦表面起了一定的隔離作用。
  7. The limit using temperature of mc nylon is 120, the gear can t work correctly if the temperature exceeds 120

    Mc尼的使用溫度極限約120 ，當摩擦熱引起的溫度上升超過此極限時，輪將無
  8. In theory and practice, it is important to build up the heat transfer equations, compute the friction heat and temperature and determine the influences on the speed and dynamics

    建立熱傳遞方程，計算軸承的摩擦熱和溫度分佈，研究軸承的熱特性，及其對速度和動力學性能的影響是一個具有理論和實際意義的重要課題。
  9. The processes of hot - spots formations of cracks friction in solid propellants under normal pressure and shear stress, are analyzed numerically

    對壓力和剪力作用下丁羥推進劑（ htpb ）和高能推進劑（ nepe ）裂紋摩擦熱點形成過程進行了數值計算。
  10. When the loading is constant, the abrasion heat rises as the rotating speed rises

    法正常工作如負載不變時，摩擦熱隨著輪轉速的增高而增大，極限情況下甚至
  11. Feasibility analysis on usage of friction heat to transport crude oil in buried hot oil pipeline

    埋地熱油管道利用摩擦熱進行原油輸送的可行性分析
  12. Influence of thermal bow on the stability of rubbing bearing - rotor system

    摩擦熱彎曲對轉子穩定性的影響
  13. Environment temperature doesn t include the heat rising caused by abrasion heat generated by running

    環境溫度不包括由於運轉而產生的摩擦熱使軸套溫度的升高。
  14. The result shows that it is mainly caused by the martensite with high hardness produced after rail absorbing frictional heat

    斷裂的主要原因是鋼軌在吸收摩擦熱后產生了高硬度的馬氏體。
  15. The friction heat in spindle bearings has obvious influences on the speed and dynamics, and is an important reason to limit machining tools for higher speed and precision

    主軸軸承的摩擦熱顯著影響主軸單元的速度和動力學性能，是制約提高加工效率和精度的主要因素。
  16. The biggest fuel savings achieved by a full hybrid vehicle derives from regenerative braking, a technology that captures as electrical power much of the energy normally lost as frictional heat

    高量級混合車最大的省油關鍵來自再生制動（煞車）技術，這種技術可捕集摩擦熱（通常幾乎散失掉的能量）並轉變成電力。
  17. In chapter 3, it systematically analyzes the bi - dimensioned instantaneous temperature range state of piston, cylinder liner and piston rings when diesel engine type 4135 is considered under the normal friction heat

    第3章系統地分析了4135柴油機在考慮摩擦熱的正常工況下活塞、缸套和活塞環各部分二維瞬態溫度的分佈和狀態。
  18. Many kinds of the heat sources ( frictional heat, cutting heat, ambient temperature, etc ) in machining system produce a kind of temperature distribution. this temperature distribution induces thermal deformation between machine tools, tool, work - piece and work holding fixture. this deformation affects the relative displacement between the work piece and the cutter, causes the manufacturing errors, and influences the machining accuracy of the work - piece

    在機械加工中，工藝系統在各種熱源（摩擦熱、切削熱、環境溫度、熱輻射等）的作用下，產生溫度場，致使機床、刀具、工件、夾具等產生熱變形，從而影響工件與刀具間的相對位移，造成加工誤差，進而影響零件的加工精度。
  19. 6 ) minimum preload analyses of spindle bearings : the paper puts forward the principles and computations of the minimum preload through an example. 7 ) speed experiment of spindle bearings : the paper testy studies the influences of ( lie structure and lubrication parameters on the speed. from the results of analysis, computation and testing, the results show : 1 ) the friction heat and preloadings of spindle bearings obvious influences the speed and dynamics

    本文全面揭示了主軸軸承的熱特性、設計和應用參數對速度和動力學性能的影l狗，不僅為主軸單元和主軸軸承的設計與應用提供了理論與試驗依據，而且提出了考慮摩擦熱和預緊方式影響的高速軸承擬動力學分析方法，具有重要的理論和應用價值。
  20. The results show that ignoring change of friction heat flow intensity will bring large deviation to temperature field simulation

    結果表明：如果忽略制動過程中摩擦熱流強度的變化，會給溫度場模擬帶來較大的偏差。
分享友人
分享到 Line

分享到臉書