操作差錯 的英文怎麼說

中文拼音 [cāozuòchācuò]
操作差錯 英文
bust
  • 操 : Ⅰ動詞1 （抓在手裡; 拿; 掌握） hold; grasp 2 （做; 從事） act; do; operate 3 （用某種語言、方言說...
  • 差 : 差Ⅰ名詞1 （不相同; 不相合） difference; dissimilarity 2 （差錯） mistake 3 [數學] （差數） differ...
  • 錯 : Ⅰ形容詞1 （錯誤; 不正確） wrong; mistaken; erroneous 2 （用於否定: 壞; 差） bad; poor 3 （交叉; ...
  • 操作 : 1 （按照一定的程序和技術要求進行活動） operate; manipulate; handle 2 （所進行的若干連續生產活動的...
  1. This scheme also works to prevent operation mistakes.

    這個安排也適用於防止操作差錯。
  2. Because of fault in operation and the precision of instrument, the defect error and accidental error are involved in the procession of data collection, the defect error that are brought by mistakes of people and influence of outside is large, the contingency error that are inevitably and randomicity is little

    在採集數據過程中，由於某些操作或儀器原因，往往使數據中包含人為錯誤，或外界干擾產生的量值較大的「過失誤差」以及不可避免的帶隨機性質且量值較小的「偶然誤差」 。
  3. The pointer offset value and sensor gain setting value selected by this operation are not initialized by setup reset or default set operation

    這里操作選定的指針偏差值和感應增益設定值不用「歸零設定」或「錯誤重調」來清除。
  4. Basic interoperability test is designed to check alarms on physical connections, the error rate of information delivery and the 2mbits cross - connect state when stm - 1 signals pass the transmission system. high - level interoperability test is to check the consistency of generated against readout overhead bytes, alarms and the performance monitoring as well as the synchronization, protection rotation, the interworking possibility of nm information and the o & m capability

    基本互通能力測試包括：檢查物理連接是否告警，檢查信息傳送有無差錯，交換機stm - 1經過傳輸系統進行2mbits交叉連接的測試；高層次互通能力測試包括：開銷位元組產生和讀出的一致性，告警一致性，性能監視一致性，同步，保護倒換，網管信息互通的可能性及維護操作能力的測試等。
  5. That test part of the software is primarily used to complete the test of some parameters, such as time base, time - expand, time interval, voltage interval, vertical, stable state, transient state and scanning linearity. the result of the test needs to be analyzed and judged. clear user interface and timely warnings for mistakes of testing process inside because of the user ' s fault operating make whole test process more easier than it did on a time

    該軟體的測試部分主要用於完成對示波器掃描時間系數、擴展掃描時間系數、 t時間測量、 v電壓測量、垂直偏轉系數、頻帶寬度、校準信號、脈沖瞬態響應、掃描線性誤差時等參數的測試檢定任務，並對測試結果進行及時的分析和判斷，由於界面清晰，而且對測試過程中由於用戶的誤操作都有及時的錯誤提示，使得整個測試過程簡單易行，對于用戶來講掌握起來也更為方便些。
  6. The chapter also dwells on the scheme of check - up system on effective management. the fourth chapter briefly states problems likely to occur in the scheme of check - up system on effective performance, ways to smooth implementation and questions for attention at the initial stage of reforms on effective performance of enterprises, as well as mistakes and problems likely to occur in future. student : directed by

    第四章就績效考核體系設計和實際操作中容易出現的問題進行簡單介紹，主要內容為績效考核方案設計中容易出現的問題和偏差，及企業績效管理改革初期順利實施的方法和應該注意的問題，並對未來實施中易犯錯誤和常見問題進行了論述。
  7. A operation performed to ensure that a new or changed program is errorfree and capable of performing its intended function

    一種操作，執行它以確保新的或經過修改的程序是無差錯的並可以執行其預定的功能。
  8. A operation performed to ensure that a new or changed program is error - free and capable of performing its intended function

    一種操作，執行它以確保新的或經過修改的程序是無差錯的並可以執行其預定的功能。
  9. For the convenience of operation, it is necessary to number 63 e1s. since there are no definite speculations about the corresponding relationship between the e1 numbers and the positions of the tributary channels in the optical circuit, vendors number the e1s on the basis of before and after multiplexing. hence two e1 numbering methods. while difference in numbering will not cause problems in interconnectivity of equipment, it will cause inconvenience of maintenance

    在使用中為了操作方便需要對63條e1進行編號，由於在itu - t的規范中，沒有具體對e1的編號和支路在光路中的位置的對應關系作明確的規定，所以不同設備供應商分別按照復用前和復用后兩種方式對e1進行編號，因此也就出現了兩種e1的編號方式，編號不一致不會造成設備對接問題，但是會造成維護的不方便，一旦分配電路時出現人為的差錯，糾正起來非常困難，因此在實施前統一不同交換機和傳輸設備的編號是十分重要的工作。
  10. The perfect quality management system can get your satisfaction smiles. eevery operating sequence has the strict norm. under the care of the professional, it can reduce the probability of mistakes and offer our good service

    完善的質量管理體，保證您的滿意微笑，每一個操作步驟都有嚴格的規范，由專人負責，保證將差錯的概率降到最低，提供滿意服務。
  11. This difference may be caused by rounding errors during insert, delete, or update actions on underlying tables

    這種差異可能是由對基礎表進行insert 、 delete或update操作時的舍入錯誤引起的。
分享友人
分享到 Line

分享到臉書